Download  Print this page

GE Interlogix 0150-0265A User Manual

Probridge gateway.
Hide thumbs

Advertisement

0150-0265A
ProBridge Gateway
PORT 1
RS-232 / RS-485
e
Kalatel Pro Bridge
SW1
1
2
3
4
5
6
7
8
O
F
F
O
N
PORT 0
RS-485
SW4
PORT 0
PORT 1
SW2
SW3
1
2
3
4
5
6
7
8
O
1
2
3
4
5
6
7
8
O
1
2
3
4
5
6
7
8
O
F
F
F
F
F
F
O
O
O
N
N
N

Advertisement

Table of Contents

   Related Manuals for GE Interlogix 0150-0265A

   Summary of Contents for GE Interlogix 0150-0265A

  • Page 1 0150-0265A ProBridge Gateway PORT 1 PORT 0 RS-232 / RS-485 RS-485 Kalatel Pro Bridge PORT 0 PORT 1...
  • Page 2 © 2003 Kalatel, a GE Interlogix company All Rights Reserved. Any GE Interlogix, Kalatel division, software This equipment has been tested and supplied with GE Interlogix, Kalatel division, found to comply with the limits for a products is proprietary and furnished under...
  • Page 3: Table Of Contents

    5.1 P DVMR ....14 RIDGE TO RIPLEX ABLE 5.2 P PC/L ......14 RIDGE TO APTOP ABLE 5.3 P I/O J ......15 RIDGE TO UNCTION ............. 16 PECIFICATIONS ......... 17 ARRANTY AND ETURN NFORMATION 0150-0265A / August 2003...
  • Page 4: Before You Begin

    ** CAUTION: Improper use of this equipment can cause equipment damage. Note: Notes contain important information about a product or procedure. * This symbol indicates electrical warnings and cautions. ** This symbol indicates general warnings and cautions. 0150-0265A / August 2003...
  • Page 5: Overview

    Gateway to the KTD-405 Keyboard and the dome cameras through the I/O junction box. This cable is 6’ in length. (1) P/N 4010-0007: 12VDC 120VAC Power Supply or P/N 4010-0008: 12VDC 220VAC Power Supply. (1) P/N 0150-0265A: ProBridge Gateway User Manual. 1.1.1 NSTALLATION NVIRONMENT Power: Ensure that the installation site’s AC power is stable and within the rated...
  • Page 6: Power

    4310-0007: 120VAC Power Supply Power Supply Input Voltage: 120 Volt AC Tolerance: ±10% Frequency: 60 Hz Power Supply Output Voltage: 12 Volt DC Current: 110mA Power: 1.3 Watts Connector: 2.1mm female barrel. Center Positive 0150-0265A / August 2003...
  • Page 7: Pro Bridge Gateway Product Diagram

    BIAS 1 - Dipswitch 1-8 TERM 1 PORT 2 RS-232 SEL RS-232 12V DC RS-485 SEL Port 2 Power Supply RS232 Connector 12VDC Note: Port 0 and Port 1 have looping RJ45 connectors. 1.3.1 IPSWITCH OSITION EGEND 0150-0265A / August 2003...
  • Page 8: Programming Mode

    ProBridge Gateway for Programming DB9F RJ45 (Port 1) RS232 4310-0047B Cable BIAS 0 + BIAS 0 - TERM 0 BIAS 1 + BIAS 1 - TERM 1 PORT 2 RS-232 SEL RS-232 12V DC RS-485 SEL 0150-0265A / August 2003...
  • Page 9: Operating Mode

    RS485 BIAS 0 + BIAS 0 - TERM 0 BIAS 1 + BIAS 1 - TERM 1 4310-0034B Cable PORT 2 RS-232 SEL RS-232 12V DC RS-485 SEL RJ45 (Port 0) ProBridge Gateway RJ45 DVMRe Triplex 0150-0265A / August 2003...
  • Page 10: Operation

    Synchronization 0xFF Length 0x07 Message type 1 0x20 Digiplex message Message type 2 312 command code CMD312_SET_PRESET(Q) / CMD312_FIND_PRESET(E) Destination Mapped camera: 0x80-0xFD* 0x80 + camera # high byte Source 0x00-0xFD keypad address <= Impac Mux/DVMRe 0150-0265A / August 2003...
  • Page 11: Movement Speed

    Port 1: PTZ message at KTD405. Message type 1=0x09, Message type 2=0x14 Message format: Synchronization 0xFF Length 0x09 Message type 1 0x09 Telemetry message type 1 Message type 2 0x14 New PTZ packet Destination 0x00-0xFD Zone = Destination + 1 (Mapped camera) 0150-0265A / August 2003...
  • Page 12 Mapped camera: Camera (site) # low byte “Monitor “ value 0 (General command parameter) Checksum 2’s complement 4.1.3.3 M OUSE OMMAND Mapped address only. Nothing else has been changed. 4.1.3.4 A Not available at this time. 0150-0265A / August 2003...
  • Page 13: Message Translation From Kalatel Rs485 Network To Legacy (impac ) Rs485 Network

    NETWORK TO EGACY MPAC NETWORK All messages are passed through unchanged (transparent), with the exception of Kalatel Menu Mode messages, which are blocked. (Message types 0x08, 0x09, 0x10, 0x11, 0x12, 0x13 and 0x14 are passed through) 0150-0265A / August 2003...
  • Page 14: Cable Specifications

    Pin 2 ProBridge to the serial port of a PC or Pin 1 Pin 1 Laptop computer. RJ-45 DB-9F Connector Connector NOTE: This cable is used for Programming ProBridge via Windows HyperTerminal RJ-45 Connector DB9F Connector 0150-0265A / August 2003...
  • Page 15: Pro Bridge To I/o Junction Box

    Connector Type: RJ45, Flying Leads Pin 5 Pin 4 Cable Required: RS-485 Flying Leads Pin 3 Pin 2 Cable. Interconnects ProBridge with Pin 1 KTD-405 and Dome Cameras. RJ-45 Flying Connector Leads RJ45 Connector Flying Leads 0150-0265A / August 2003...
  • Page 16: Specifications

    Power Supply Voltage: 12 VDC Current: 110 mA Power: 1.5 W Note: All specifications are subject to change without notice. Kalatel believes that all specifications are correct, however no liability is assumed for omissions or errors. 0150-0265A / August 2003...
  • Page 17: Warranty And Return Information

    • Fewer than 45 days from purchase, GE Interlogix, Kalatel division, will replace the product with new equipment. • From 45 days to 1 year from purchase, GE Interlogix, Kalatel division, will replace the product with refurbished equipment. • From 1 year to 3 years from purchase, the product must be sent in for repair.

Comments to this Manuals

Symbols: 0
Latest comments: