Icom Iç-V88 Operating Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Transceiver
  5. Ic-V88
  6. Operating manual

Icom Iç-V88 Operating Manual

Vhf transceiver/uhf transceiver
Hide thumbs Also See for Iç-V88:
Table of Contents

Advertisement

Quick Links

OPERATING GUIDE
VHF TRANSCEIVER
Iç-V88
UHF TRANSCEIVER
Iç-U88

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Iç-V88 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Icom Iç-V88

Summary of Contents for Icom Iç-V88

  • Page 1 OPERATING GUIDE VHF TRANSCEIVER Iç-V88 UHF TRANSCEIVER Iç-U88...

  • Page 2: Table Of Contents

    D Selecting the RX and TX tones ........8 D Editing the channel name...........10 D Other settings .............11 Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/ or other countries.

  • Page 3: Accessories

    Section ACCESSORIES Accessory attachments Antenna Connect the supplied or an optional antenna to the an- tenna connector. CAUTION: • NEVER carry the transceiver by holding only the antenna. • DO NOT connect any antenna other than those listed in OPTIONS in INSTRUCTIONS w that is provided with the transceiver.

  • Page 4: D Jack Cover

    ACCESSORIES Accessory attachments (Continued) Jack cover To attach the jack cover: q Place the jack cover over the speaker-microphone jack. w Insert and tighten the screws. CAUTION: The transceiver meets IP67 requirements for dust-tight and waterproof protection, only when the jack cover or the optional HM-168LWP speaker is attached.

  • Page 5: Programmable Key Functions

    Section PROGRAMMABLE KEY FUNCTIONS Programmable key functions If you use the CS-V88 (purchase cLOning sOftware separately), you can assign the functions described below to [P0], [P1], [P2], [P3], [TOP], [UP], and [DOWN]. NOTE: About the default settings of these keys, see the in- struction manual that is provided with the transceiv- CH UP/DOWN MEMORY CHANNELS 1, 2, 3, 4...

  • Page 6: Programmable Key Functions

    PROGRAMMABLE KEY FUNCTIONS Programmable key functions (Continued) DTMF AUTODIAL SHIFT Push to enter the DTMF number selection mode, 1. Push to turn ON the Shift mode key functions. ➥ then select a DTMF number by pushing [CH Up] or • “SHIFT ON” is briefly displayed. 2.

  • Page 7: Mdc 1200 System Operation

    An additional feature of the MDC 1200 system included eration. in Icom transceivers is called aliasing. Each transceiv- er on the system has a unique ID number. Aliasing is a substitute for this ID number and you can give an alphanumeric name for each station ID.

  • Page 8: User Set Mode

    Section USER SET MODE User Set mode The User Set mode enables you to change various set- tings. You can “customize” the transceiver operation to suit your preferences and operating style. Entering the User Set mode: [P0] to enter the User Set mode. Hold down ➥...

  • Page 9: Front Panel Programming

    Section FRONT PANEL PROGRAMMING Front Panel Programming mode The following settings can be changed in the Front Panel Programming mode without a PC. This is a con- venient function to immediately change some settings when you operate the transceiver in the field. •...

  • Page 10: D Editing The Receive (Rx) And Transmit (Tx) Frequencies

    FRONT PANEL PROGRAMMING Front Panel Programming mode (Continued) Editing the Receive (RX) and Transmit (TX) Selecting the RX and TX tones frequencies These instructions are the same to select both the RX and TX tones. These instructions are the same to edit both the RX and TX frequency.
  • Page 11 FRONT PANEL PROGRAMMING Front Panel Programming mode Setting the CTCSS tone frequency: Selecting the RX and TX tones (Continued) [UP] or [DOWN] When CTCSS tone is selected, push to select the frequency. [P2] to select the CTCSS tone frequency, or Push DTCS code screen, or to turn OFF the CTCSS tone frequency.

  • Page 12: D Editing The Channel Name

    FRONT PANEL PROGRAMMING Front Panel Programming mode (Continued) Editing the channel name When using the 10-key pad: You can display the name instead of the channel number. Repeatedly pushing [2], for example, first selects the ➥ number “2.” Continuing to push it selects upper case While any of the TX tones are displayed, as described letters “A,”...

  • Page 13: D Other Settings

    FRONT PANEL PROGRAMMING Front Panel Programming mode (Continued) Other settings To clear the RX frequency memory: To deactivate the channel: Select an RX frequency as described on page 8. Select a desired zone and a channel, as described on page 7. LED: Green [P2] to clear the memory.
  • Page 14 A-7140-3EX-q 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan © 2014 Icom Inc.

This manual is also suitable for:

Iç-u88

Table of Contents

Save PDF