Playing Video Images Recorded In The Memory Recorder - JVC KA-MR100G Instructions Manual

Playing Video Images
Recorded in the Memory
Recorder
To play back video images recorded by the memory
recorder, select a clip from the clip selection screen on the
LCD panel of the memory recorder. The selected video clip
is played back on the LCD monitor and viewfinder of the
camcorder.
:
Memo
● Before playing back video images recorded by the memory
recorder, stop the playback of the cassette tape in the
camcorder.
● Images on the LCD monitor and viewfinder of the
camcorder may be distorted when in the Still and Fast
forward/Fast reverse modes.
Settings Prior to Playback
Before playing, it is necessary to configure the camcorder
and memory recorder settings.
Camcorder settings
1 Set to the AVTRB mode using the [CAM/VTR]
button
2 Set the [IEEE1394] switch to the AHDVB end
Memory recorder settings
For procedures to set the menu screen, refer to page 11.
1 Set the video format
● Set the RESOLUTION and FRAME/RATE under the
[SYSTEM] settings on the menu screen. (A Page 12)
Note:
● Set according to the format settings of the camcorder.
Playback cannot be executed if the camcorder and
memory recorder settings are different from each other.
Playing a Clip from the SxS Memory
Card
If the memory recorder is in the standby mode, press the
[STOP] button on the recorder to switch to the stop mode.
[PREV]
button
[REV]
button
<LCD Panel>
Normal playback
1 Press the [PLAY/STILL] button
:
Memo
● Playable clips are indicated by a check mark (
front of their names.
● The clip indicated by the cursor (
ALCD Panel DisplaysB (A Page 5)
[PLAY/STILL] button
[FWD] button
[STOP] button
[NEXT]button
<Buttons to use>
) at the
) is the selected clip.
2 Press the [NEXT] or [PREV] button to select a
clip to play
● Select a clip that has a check mark.
● To play back a clip without a check mark, it is necessary to
configure the camcorder and memory recorder according
to the video format settings, which are displayed when the
clip is selected.
3 Press the [PLAY/STILL] button to start playback
● The video clip is played back on the LCD monitor and
viewfinder of the camcorder.
● The progress bar on the LCD panel of the memory
recorder moves to indicate the current playback position.
● Press the [PLAY/STILL] button during playback to switch
to the still mode. Press the button again to resume
playback.
:
Memo
● When multiple video clips are stored in the SxS memory
card, the playable clips are played back continuously in
sequence. Playback switches to the still mode at the end
of the last clip.
4 Press the [STOP] button to stop playback of the
clip
The LCD panel display switches to the status screen.
Fast forward/Fast reverse
Fast forwards or fast reverses the selected clip. It will switch
to still mode at the end or beginning of the selected clip. To
switch to the still mode during fast forward or fast reverse,
press the [PLAY/STILL] button.
Pressing the [FWD] button in the still mode,
during playback or fast reverse
Switches to the low speed fast forward (F1) mode. Press the
[FWD] button again to switch to the high speed fast forward
(F2) mode.
Pressing the [REV] button in the still mode,
during playback or fast forward
Switches to the low speed fast reverse (R1) mode. Press the
[REV] button again to switch to the high speed fast reverse
(R2) mode.
Skip
Skips to the next or previous playable clip.
Pressing the [NEXT] button in the still mode or
during fast reverse
Doing so switches automatically to the still mode after
skipping to the beginning of the next clip. Pressing the button
twice switches to the still mode after skipping to the
beginning of the second clip from the current one.
Pressing the [PREV] button in the still mode or
during fast reverse
Pressing this button during playback of the clip switches
automatically to the still mode after skipping to the beginning
of the selected clip. Pressing the button again skips to the
beginning of the previous clip and remains in the still mode.
Pressing the [NEXT] button during playback or
fast forward
Pressing the button starts playback automatically from the
beginning of the next clip. Pressing the button twice starts
playback from the beginning of the second clip from the
current one.
Pressing the [PREV] button during playback or
fast forward
Pressing this button during playback of the clip starts
playback automatically from the beginning of the selected
clip. Pressing the button at the beginning of the clip starts
playback from the beginning of the previous clip.
10