Troubleshooting - JVC KA-MR100G Instructions Manual

Others

Troubleshooting

Symptom
Power does not turn Power is supplied from the DC INPUT
on terminal of the camcorder.
Only the power of the camcorder is turned
AOnB.
Remaining battery level is insufficient.
Unable to record or The IEEE1394 cable is not connected.
play clip
The [INT/EXT] switch setting of the
KA-UM100G adapter is inappropriate.
The video formats of the camcorder and
memory recorder are not consistent with
each other.
The [IEEE1394] switch of the camcorder is
set to the ADVB end.
Recording does not The camcorder is set to the AVTRB mode.
start
The [1394 REC TRIGGER] item on the
OTHERS[2/2] menu screen of the
camcorder is set to AOFFB or ASERIESB.
The memory recorder is set to the playback
mode.
The write-protect of the SxS memory card
is enabled.
There is no space left on the SxS memory
card.
Unable to play clip The camcorder is set to the ACAMB mode.
The cassette tape is currently being played
back.
A clip without the check mark (v) is
selected.
The memory recorder is in the recording or
standby mode.
The clip may be damaged.
No response when a The [OPERATION] menu is set to ALOCKB. Change the [OPERATION] menu setting to AUNLOCKB.
button is pressed
A multiple number of buttons are pressed
at the same time, or the same button is hit
repeatedly.
Access lamp does not The SxS memory card is not completely
turn on inserted into the card slot.
The SxS memory card is inserted with the
label facing the opposite direction.
SxS memory card A SxS memory card that is formatted by
cannot be used another device is used.
A media that is not supported is inserted.
The clip is faulty.
Error message ADR-HD100 POWER ?B appears when the
appears on the memory recorder is not powered on or is
camcorder panel not connected.
display
AHDD NO 1394 SIGNALB appears if the
camcorder is set to the "CAM" mode when
the memory recorder is in playback mode.
AHDD SPACE LOWB appears when the
space on the SxS memory card is
insufficient or an SxS memory card is not
inserted.
15
Cause(s) Actions
Attach the battery. The power of the memory recorder
cannot be supplied from the DC INPUT terminal of the
camcorder.
It is necessary to turn on the power of the memory recorder
at the same time.
Charge the battery.
Connect a GY-HD200/HD250 series camcorder to the
KA-UM100G adapter using an IEEE1394 cable.
● Set to AEXTB during normal use. (When IEEE1394
connection is made internally without the use of an
external cable, set to AINTB.
● If the ANO SIGNALB message does not disappear even
if the setting is correct, set the switch again to select the
setting. If the message remains displayed, turn off and
on the power again.
Ensure that the video format of the camcorder and memory
recorder are consistent with each other.
Set the [IEEE1394] switch to the AHDVB end.
If the ANO SIGNALB message does not disappear even
after setting to AHDVB, set the switch again. If the message
remains displayed, turn off and on the power again.
Set to the ACAMB mode using the [CAM/VTR] button.
Set [1394 REC TRIGGER] to ASYNCROB or ASPLITB.
When this is set to ASERIESB, recording starts when the
remaining capacity of the cassette tape falls below three
minutes.
Press the [STOP] button to stop playback.
Set the write-protect switch to AOffB before recording or
deleting a clip.
Use an SxS memory card that has sufficient space.
Set to the AVTRB mode using the [CAM/VTR] button.
Stop playback of the cassette tape before playing back
data on the SxS memory card.
Set the camcorder and memory recorder according to the
video format displayed when a clip is selected.
Press the [STOP] button to stop playback.
Execute ARESTOREB using this memory recorder.
Insert a short pause between each button operation.
Make sure that the SxS memory card is fully inserted into
the slot.
Identify the face of the SxS memory card with the label,
and make sure that the card is correctly oriented before
inserting.
Execute AFORMATB using this memory recorder.
Replace it with a recommended SxS memory card.
Execute ARESTOREB or AFORMATB using this memory
recorder. If doing so does not eliminate the error, replace it
with a recommended SxS memory card.
Connect and turn on the power of the memory recorder.
Set the camcorder to the AVTRB mode.
Use an SxS memory card that has sufficient space.
Refer to
A Page 7
A Page 7
A Page 14
A Page 7
A Page 7
A Page 9
A Page 9
A Page 10
A Page 9
A Page 9
A Page 9
A Page 14
A Page 14
A Page 10
A Page 10
A Page 10
A Page 10
A Page 14
A Page 14
^
A Page 8
A Page 8
A Page 13
A Page 14
A Page 14
A Page 6
A Page 7
A Page 10
^