Table of Contents
Advertisement
OBJ_BUCH-1845-002.book Page 14 Friday, June 14, 2013 12:48 PM
14 | English
3 Thumbwheel for speed preselection
4 On/Off switch
5 Auxiliary handle (insulated gripping surface)
6 Dust cover
7 Feather key
8 Locking screw
9 Tool bit*
10 Spindle extension
11 Guide roller
12 Wing nuts
13 Handle (insulated gripping surface)
14 Allen key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Satin-Finisher
Article number
Rated power input
No-load speed
Max. outer diameter of
application tool
Max. width of application tool
Mounting hole diameter
Speed preselection
Soft start
Constant electronic control
Restarting Protection
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 89 dB(A); Sound power level
100 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
2
a
=5.0 m/s
, K=1.5 m/s
.
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
3 609 929 C51 | (14.6.13)
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9
D-70745 Leinfelden-Echterdingen
Henk Becker
GSI 14 CE
Executive Vice President
3 601 HB1 0..
Engineering
W
1400
-1
min
750 – 3000
mm
115
Robert Bosch GmbH, Power Tools Division
mm
100
D-70745 Leinfelden-Echterdingen
08.06.2013
mm
19
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust/Chip Extraction
kg
3.4
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
/II
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Mounting the Auxiliary Handle and Dust Cover
(see figure A)
Only work with the auxiliary handle 5 mounted.
– Loosen screw 2 of the dust cover 6 using the provided Al-
len key 14.
– Place dust guard 6 onto the spindle flange. Move dust cov-
er 6 accordingly to suit your working conditions and work-
ing position.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools
Advertisement
Table of Contents
