Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch Professional GWS 600 Original Instructions Manual

OBJ_BUCH-2659-002.book Page 7 Thursday, October 20, 2016 4:31 PM
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.

Intended Use

The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Auxiliary handle (insulated gripping surface)
4 Combination spanner for M 14 grinder spindle*
5 Combination spanner for M 10 grinder spindle*
6 Grinder spindle
7 Protection guard for grinding
8 Locking screw for protection guard
9 Mounting flange with O-ring
10 Grinding wheel*
11 Clamping nut
12 Quick-clamping nut
13 Carbide grinding head*
14 Protection guard for cutting*
15 Cutting disc*
16 Hand guard*
17 Rubber sanding plate*
18 Sanding sheet*
19 Round nut*
20 Cup brush*
21 Cutting guide with dust extraction protection guard *
22 Diamond cutting disc*
23 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Angle Grinder
Article number
Rated power input
Output power
Rated speed
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools
Angle Grinder
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder
spindle
Weight according to
EPTA-Procedure 01:2014
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
Protection Guard for Grinding
Place the protection guard 7 on the spindle collar. Adapt the
position of the protection guard 7 to the requirements of the
work step. Lock protection guard 7 by tightening locking
screw 8 with combination spanner 4/5.
 Adjust the protection guard 7 in such a manner that
sparking is prevented in the direction of the operator.
Note: The encoding keys on the protection guard 7 ensure
*
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 14 is mounted in the same
manner as the protection guard for grinding 7.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 21 is
mounted in the same manner as the protection guard for
grinding 7.
Auxiliary Handle
 Operate your machine only with the auxiliary handle 3.
Screw the auxiliary handle 3 on the right or left of the machine
GWS 600
head depending on the working method.
0 601 375 0..
Hand Guard
W 670
 For operations with the rubber sanding plate 17 or with
W 400
the cup brush/wheel brush/flap disc, always mount the
-1
min 11000
hand guard 16.
The hand guard 16 is fastened with the auxiliary handle 3.
English | 7
GWS 600
mm 100
M 10
mm 17
kg 1.5
/II
1 609 92A 2V6 | (20.10.16)