JVC GET0602-001A Instruction Manual page 143

KW-AVX726/KW-AVX724/
KW-AVX626/KW-AVX624
Installation/Connection Manual
GET0605-010A
[A/UI]
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving. It may lead to carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to look around carefully or you may be involved in
a traffic accident.
• If the parking brake is not engaged, "Parking Brake" appears on the monitor, and no playback picture
will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake system built
in the car.
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
Main unit
Flat head screws (M5 × 8 mm)
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Do the required electrical connections.
• See pages 2 – 4.
4
Install this unit using the screws removed in step
The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.
Mounting bracket removed from the car
Supplied screws
Select the appropriate
type fitting to your
audio system space.
Note : When installing the unit on the mounting bracket, make sure to use the supplied
screws (M5 × 8 mm). If longer screws are used, they could damage the unit.
Power cord
Round head screws (M5 × 8 mm)
1
.
Mounting bracket removed from the car
Screws removed from the car in step
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with maximum power of more than 50 W (both at the rear and
at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change <Amplifier Gain> setting to prevent the speakers from
being damaged (see page 18 of the INSTRUCTIONS).
• To prevent short circuits, cover the
terminals of the UNUSED leads with
insulating tape.
• The heat sink becomes very hot after use.
Be careful not to touch it when removing
this unit.
Plate for use with a Nissan car
Remote controller
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used,
parts could become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
Supplied screws
1
If necessary, restore the protruding tabs.
1
0109DTSMDTJEIN
© 2009 Victor Company of Japan, Limited
Heat sink
Crimp connector
Batteries
When installing the unit in a Nissan car
Plate for use with a Nissan car
Required space for installation and the
monitor ejection
20
Dashboard
160 91.3
Install the unit at an angle of less than 30˚, taking it into
account that the monitor would eject when in use.
30˚
EN
Unit: mm