Download Print this page

Haier HSU18VHK-W Installation Manual

Haier easy series 18/24k (208-230/1/60) split systems air conditioner installation manual
Hide thumbs

Advertisement

Installation Manual of Easy Series 18/24K (208-230/1/60)
Preparation
Necessary Tools for Installation
● Drill
● Nipper
● Saw
● Hole 2 3/4
● Vacuum pump
Gas leakage detector or
soap-and-water solution
● Torque wrench
(17mm,22mm,26mm)
● Pipe cutter
● Flaring tool
● Knife
● Measuring tape
● Reamer
Drawing for the installation of indoor and outdoor units
Procedure for Selecting the Location
Choose a place solid enough to bear the weight and vibration of the unit,where the operation noise will not be amplified
Choose a location where the hot air discharged from the unit or the operation noise,will not cause a nuisance to the neighbors
of the user.
Avoid places near a bedroom and the like,so that the operation noise will cause no trouble.
There must be sufficient space for carrying the unit into and out of the site.
There must be sufficient space for air passage and no no obstructions aroud the air inlet and air outlet.
The site must be free from the possibility of flammable gas leakage in a nearby place.
Locate the unit so that the noise and discharged hot air will not annoy the neighbors.
Install units,power cords and inter-unit cables at least 10ft away from televison and radio sets,This is prevent interference to
images and sounds.(Noise may be heard even if they are more than 10ft away depending on radio wave conditions.)
In coastal areas or other places with salty atmosphere of sulfate gas,corrosion may shorten the life of the air condition.
Since drain flows out of the outdoor unit,do not place under the unit anything which must be kept away from moisture.
NOTE: Cannot be installed hanging from ceiling or stacked.

Advertisement

loading

  Also See for Haier HSU18VHK-W

  Related Manuals for Haier HSU18VHK-W

  Summary of Contents for Haier HSU18VHK-W

  • Page 1 Installation Manual of Easy Series 18/24K (208-230/1/60) Preparation Necessary Tools for Installation Procedure for Selecting the Location ● Drill ● Choose a place solid enough to bear the weight and vibration of the unit,where the operation noise will not be amplified ●...
  • Page 2: Indoor Unit

    1. Insert the drain hose into the dent of heat insulation materials of indoor unit. Accessory parts 2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them. Remote controller (1) Drain hose (1) 3.
  • Page 3: Outdoor Unit

    50 g/m. cable Outdoor unit Connection Take off the panel(top), by removing the 5 screws. 2 Wire with ground 12AWG HSU18VHK-W Power cable: 2 Wire with ground 12AWG Remove the plugs on the conduit plate. Power cable: HSU24VHK-W Temporarily mount the conduit tubes on the conduit plate.
  • Page 4 No gas leakage? On Drainage In case of gas leakage, tighten parts of pipe connection. If leakage stops, Please install the drain hose so as to be downward slope without fail. then proceed step 6. If leak continues, remove the refrigerant used for the Please don’t do the drainage as shown below.
  • Page 5: Fuente De Alimentación

    Manual de instalación de aparato de aire acondicionado Preparación Herramientas necesarias para realizar la instalación Selección del lugar de instalación Unidad interior – Elija una ubicación que sea Martillo Llave dinamométrica (17 mm, 22 mm, 26 mm) Firme y que no provoque vibraciones, que pueda soportar la unidad adecuadamente. Alicate Que no se vea afectada por calor o vapor generado en las cercanías y donde las Sierra para metales...
  • Page 6: Unidad Interior

    1. Pase la manguera aislante a través del hueco de los materiales de aislamiento de Accesorios calor de la unidad interior. 2. Inserte los cables eléctricos de interior / exterior a través de la parte trasera de la unidad interior y tire de ellos desde la parte delantera. A continuación, conéctelos. 3.
  • Page 7: Unidad Exterior

    En caso de que la longitud del tubo B sea superior a 10m, deberá cargarse el refrigerante a razón de 50 g/m. Unidad exterior 2 hilos con toma de tierra 14AWG HSU18VHK-W Cable de alimentación: 2 hilos con toma de tierra 14AWG HSU24VHK-W Cable de alimentación: Conexión...
  • Page 8 5. ¿No existen fugas de gas? 1. Cortar el tubo 2. Eliminar las rebabas Cuchilla de conicidad En caso de que exista una fuga de gas, apriete las conexiones de los tubos. Si la fuga se detiene, proceda al paso 6. 3.
  • Page 9 Manuel d'installation d'un climatiseur de pièce Préparation Outillage requis pour l'installation Sélection de l'emplacement pour l'installation Unité intérieure – Sélectionnez un emplacement qui soit Marteau Clé dynamométrique (17 mm, 22 mm, 26 mm) Solide sans vibration et offrant un support Pince N'est pas affecté...
  • Page 10: Unité Intérieure

    dans thermique Accessoires le joint évasé avec de réfrigérante et Télécommande (1) Tuyau de vidange (1) la pièce de avec des thermique et avec du ruban adhésif. Batterie sèche AAA (2) Coussinet (4) C ble électrique des unités intérieures/e érieures Plaque de Coude de vidange (1) Tuyauterie...
  • Page 11: Unité Extérieure

    Longueur max: Bmax=25m Unité intérieure Si la longueur du tuyau B dépasse les 10m, le réfrigérant doit être chargé à 50 g/m. fils avec terre, 14AWG HSU18VHK-W Câble d’alimentation : fils avec terre, 14AWG HSU24VHK-W Câble d’alimentation : Raccordement HSU18VCK-W Câble d’alimentation :...
  • Page 12 5. Pas de fuite de gaz? Correct Incorrect En cas de fuite de gaz, resserrez les pièces de connexion du tuyau. Lorsque la fuite est maîtrisée, passez à l'étape 6 Evasement endommagé Fissure Partiel Vers extérieur Vidange 6. Détachez le tuyau de charge de d'entretien, ouvrez la vanne à...

This manual is also suitable for:

Hsu24vhk-wHsu18vck-wHsu24vck-w