Audio Dubbing; Insert Editing - JVC GR-D20 Instructions Manual

Audio Dubbing

The audio track can be customized only when recorded
in the 12-bit mode ( pg. 21).
NOTES:
Audio Dubbing is not possible on a tape recorded in
16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
To perform Audio Dubbing while watching on the
television, make connections (
1
Play back the tape to locate the point where editing
will start, then press PAUSE (6)
2
While holding A.DUB (e)
T
press PAUSE (6) . "6e"
only) appear.
3
h
Press PLAY (4) , then begin "narrating".
Speak into the microphone.
• To pause dubbing, press PAUSE (6)
4
To end Audio Dubbing, press PAUSE (6)
O
STOP (5) .
To hear the dubbed sound during playback . . .
..... set "12BIT MODE" to "SOUND 2" or "MIX" in the
Menu Screen ( pg. 25).
NOTES:
Sound is not heard from the speaker during Audio
Dubbing.
When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
If feedback or howling occurs during TV playback, move
the camcorder's microphone away from the TV, or turn
down the TV's volume.
If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (
To perform Audio Dubbing with a video unit connected to
the camcorder's AV connector, first set "S/AV INPUT" to
"ON" in the Menu Screen (GR-D50/D30 only,
"AUX" appears instead of "MIC".
Stereo microphone
pg. 15).
T
.
j
on the remote control,
y
and "MIC" (GR-D50/D30
T
.
T
, then
pg. 44).
pg. 24).

Insert Editing

You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
NOTES:
Before performing the following steps, make sure that
"TIME CODE" is set to "ON" in the Menu Screen
( pg. 24, 25).
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
To perform Insert Editing while watching in the television,
make connections ( pg. 15).
1
Play back the tape, locate the Edit-Out point and
T
press PAUSE (6) . Confirm the time code at this
point ( pg. 24, 25).
2
U
Press REW (2) until the Edit-In point is located,
T
then press PAUSE (6)
3
Press and hold INSERT (w)
control, then press PAUSE (6)
Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.
4
Press START/STOP
• Confirm the insert at the time code you checked in
step 1.
• To pause editing, press START/STOP
again to resume editing.
5
To end Insert Editing, press START/STOP
O
STOP (5) .
NOTES:
Programme AE with special effects (
used to spice up the scenes being edited during Insert
Editing.
During Insert Editing, the date and time information
changes.
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops ( pg. 44).
E
R
T
Y
9
U
2
I
O
P
USING THE REMOTE CONTROL UNIT
.
I
on the remote
T &
. "6w" and the
a
to begin editing.
a
. Press it
a
pg. 16) can be
W
a
s
d
6
f
0
g
4
3
h
w 5 e
j
k
T
l
W
;
, then
EN
29