Table of Contents
Advertisement
Make sure "REMOTE" in the SYSTEM Menu is set
to "ON" (
pg. 23) and the remote control is
pointed at the remote sensor
beam's approximate effective distance for indoor
use is 5m.
Slow-Motion Playback
To allow slow-speed search in either direction during
tape playback.
1
To change from normal to Slow-Motion Playback,
Y
press SLOW (9)
seconds. After approx. 5 minutes (approx. 20 seconds
with an 80-minute cassette) in Slow Rewind or approx.
5 minutes in Slow Forward, normal playback resumes.
To stop Slow-Motion Playback, press PLAY (4)
NOTES:
You can also engage Slow-Motion Playback from Still
Playback by pressing SLOW
2 seconds.
During Slow-Motion Playback, due to digital image
processing, the picture may take on a mosaic effect.
Y
After SLOW (9)
image may be displayed for a few seconds, followed by a
blue screen for a few seconds. This is not a malfunction.
There may be a small margin between the slow-motion
playback start point you chose and the actual start point
for Slow-Motion Playback.
During Slow-Motion Playback, there will be disturbances
in video and the picture may seem unstable, especially
with steady images. This is not a malfunction.
During Slow-Motion Playback, press PAUSE (6)
pause playback.
E
R
T
Y
U
I
O
P
Frame-By-Frame Playback
To allow frame-by-frame search during tape playback.
1
To change from normal to Frame-By-Frame
Playback, press SLOW (0)
Y
SLOW (9)
repeatedly for reverse. Each time it is
pressed, the frame is played back.
NOTE:
You can also engage Frame-By-Frame Playback from Still
Playback by pressing SLOW (
EN
28
USING THE REMOTE CONTROL UNIT
1
. The transmitted
f
or (0)
more than approx. 2
Y f
more than approx.
f
or (0)
is pressed and held, the still
W
a
s
d
6
f
0
9
g
4
2
3
h
w
5
e
j
k
T
l
W
;
f
repeatedly for forward or
Y
f
9
)
or (0)
repeatedly.
Playback Special Effects
To allow you to add creative effects to the playback
image.
1
To start playback, press PLAY (4)
2
Point the remote control at the camcorder's remote
sensor and press EFFECT
EFFECT Select Menu appears.
3
Move the highlight bar to the desired effect by
pressing EFFECT
and after 2 seconds the menu disappears.
To deactivate the selected effect, press ON/OFF
on the remote control. Pressing it again re-activates
the selected effect.
To change the selected effect, repeat from step 2
above.
h
.
NOTE:
The effects that can be used during playback are Classic
Film, Monotone, Sepia and Strobe. The effects work the
same in playback as they did in recording. Refer to page 16
for more information.
To magnify the recorded image up to 44X at any time
during playback.
1
Press PLAY (4)
2
Press the Zoom Button T
control. Make sure the remote control is pointed at the
T
camcorder's remote sensor. Pressing T
to
3
You can move the image on screen around to find a
particular portion of the picture. While holding down
P
, press * (Left)
SHIFT
and
(Down)
&
To end zoom, press and hold W
returns to normal. Or, press STOP (5)
press PLAY (4)
NOTES:
Zoom can also be used during slow-motion and still
playback.
Due to ditital image processing, the quality of the image
may suffer.
Normal playback
h
d
. The PLAYBACK
d
. The selected function is activated
Playback Zoom
h
to find the scene of interest.
l
;
or W
U
g
, T(Right)
O
.
;
until magnification
h
.
l
Press T
To move image, press T
(Right)
SHIFT
.
s
on the remote
l
zooms in.
T
,
(Up)
^
O
and then
g
while keeping
P
held down.
Hide quick links:
Advertisement
Table of Contents
