Step 1 Remove Packaging; Step 2. Move Refrigerator Into House; Step 3 Install Water Line - GE Side by Side Refrigerators Installation Instructions Manual

STEP 1 REMOVE PACKAGING

WARNING
The refrigerator is much heavier at the top than at the
truck, handle from the side only.
AVERTISSEMENT
Le réfrigérateur est beaucoup plus lourd en haut qu'en
bas. Il faut être prudent lors des déplacements. Si un
diable est utilisé, il faut soulever le réfrigérateur sur le
côté seulement.
• Carefully cut banding at the top and bottom, remove
the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE CABINET DOWN
IN ORDER TO REMOVE THE SKID!
• The unit is secured to the
skid with 4 slotted tie-
down straps. Remove the
six 7/16" bolts from the
base channels in the tie-
downs.
• Remove the six 7/16" bolts
securing the straps to the
skid.
NOTE: DO NOT ATTEMPT TO
ROLL UNIT OFF SKID.
• The support blocks on the
bottom of the refrigeration
case must be removed before the refrigerator is taken
off the skid or damage will occur. Carefully tilt the
refrigerator and slide the blocks out from beneath.
• Remove the toekick and set aside for final installation.
• Lift the refrigerator off the skid with an appliance dolly.
Handle from the sides.
STEP 2 MOVE THE REFRIGERATOR
INTO THE HOUSE
• Re-use the corner posts from the packaging to protect
stainless steel models. Run the appliance dolly straps
over the posts and under the handles.
• Leave the protective film on the refrigerator until
installation is complete.IMPORTANT: Never lift the
refrigerator by the handle or push against the grill
panel; this could cause damage or misalignment.
• Avoid laying the unit on its back or side to prevent
sealed system restrictions.
Installation Instructions
Tip Over Hazard.
Risque de basculement
Remove
Tie Downs

STEP 3 INSTALL WATER LINE

• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and
120 p.s.i.
• Route 1/4" OD copper or GE SmartConnect
tubing between house cold water line and the water
connection location.
• The tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate the bend leading into the water line
connection.
NOTE: The only GE approved plastic tubing is supplied
in the GE SmartConnect
not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
GE SmartConnect Refrigerator Tubing Kits are
™
available in the following lengths:
2' (.6 m) WX08X10002
6' (1.8 m) WX08X10006
15' (4.6 m) WX08X10015
25' (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
16
plastic
™
Floor
Cold Water Line
Refrigerator Tubing kits. Do
™