Partner K950 CHAIN Operator's Manual
  1. Manuals
  2. Brands
  3. Partner Manuals
  4. Chainsaw
  5. K950 Active
  6. Operator's manual

Partner K950 CHAIN Operator's Manual

Cut-off saw
Hide thumbs Also See for K950 CHAIN:
Table of Contents

Advertisement

Quick Links

Enlarged version

K950 CHAIN

Operator's manual
Read these instructions carefully and
make sure you understand them
before using the machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K950 CHAIN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Partner K950 CHAIN

Summary of Contents for Partner K950 CHAIN

  • Page 1: K950 Chain

    K950 CHAIN Operator’s manual Read these instructions carefully and make sure you understand them before using the machine.

  • Page 2: Symbol Explanation

    Avoid breathing petrol fumes and exhaust gases. Provide for good ventilation. Warning Sparks from the cut-off saw can cause fire in combustible materials such as: petrol (gas), wood, dry grass etc. Noise emission to the environment according to the European Community’s...

  • Page 3: Table Of Contents

    Setting the idling speed is described in the Operator’s Manual. Adjust the speed according to these instructions. Do not use the cut-off saw if the idling speed is not correctly adjusted! • Let your Partner dealer check the cut-off saw and carry out essential adjustments and repairs.

  • Page 4: Safety Instructions

    WARNING! Incorrect or careless use of a cut-off saw can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand this manual. PERSONAL PROTECTIVE EQUIPMENT WARNING! When using a cut-off saw, approved protective equipment must be used.

  • Page 5: Control, Maintenance And Service Of The Machine's Safety Equipment

    WARNING! All service and repairs to the cut- off saw require special training. This applies especially to the cut-off saw’s safety equipment. If the cut-off saw does not meet any of the controls listed below you should contact your service workshop.

  • Page 6: Throttle Lock

    • Do not lend the cut-off saw to anyone without providing this Operator’s Manual. Ensure the person using the cut-off saw understands the information in this Operator’s Manual. Storage • Store the cut-off saw under lock and key so that it’s out of reach for children and unauthorised persons.

  • Page 7: Fuel Safety

    • Store the cut-off saw and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.

  • Page 8: Using

    Never start the saw without the complete bar and chain fitted. Wet cutting The diamond chain saw must always be run with water cooling. Dry cutting causes immediate overheating and bar and chain failure with a risk of personal injury. In addition to cooling the bar and chain, the flow of water pushes particles away from the bar and the drive links.
  • Page 9 Start by making a 10 centimetre deep cut in the wall using the lower part of the tip of the bar. Straighten up the saw at the same time as the tip of the bar is inserted in the slot. Raising and lowering the saw at the same time as it is pressed into the wall provides an effective method of cutting to the full depth.

  • Page 10: Water Cooling

    Partner’s cut-off saws are robust and durable. However, as they are used for high speed operations all servicing should be carried out on time and as specified, so that the cut-off saw always works effectively and safely. Read this Operator’s Manual to determine which service routines you can carry out and ensure that all other service work is carried out by an authorised service workshop.

  • Page 11: Cutting Equipment

    These safety features must be checked before work starts. Never use the saw if any of the following parts are damaged or missing: – Cover over drive gear – Damaged or missing hand guard –...

  • Page 12: What Is What

    What is what on the machine? Cylinder cover Muffler Fuel tank Starter throttle catch Choke Throttle trigger lockout Stop switch Bar and chain Water hose, quick connection 10. Chain tensioning handle 11. Counter screw 12. Throttle control – English WHAT IS WHAT? 13.

  • Page 13: Assembly

    How to tension the chain Untensioned chain. Start with opening the adjust screw cover. Pull the handle backwards. Continue to move the handle down-wards until you start to tension the chain. Hold the bar upwards as you move the handle forward. Tighten the adjust screw.

  • Page 14: How To Change The Clamping Force Of The Bar

    How to change the clamping force of the bar Check weather the handle feel loose. Turn the outer handle clockwise as far as possible and make a mark in the top position of the centre nut. Turn the outher handle anticlock- wise to remove it.

  • Page 15: Fuel Handling

    Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly before filling the saw’s fuel tank. • Do not mix more than max. one month’s supply of fuel. • If the power cutter is not used for some time the fuel tank should be emptied and cleaned.

  • Page 16: Start And Stop

    – English START AND STOP Wet cutting The diamond chain saw must always be run with water cooling. Dry cutting causes immediate overheating and bar and chain failure with a risk of personal injury. In addition to cooling the bar and chain, the flow of water pushes particles away from the bar and the drive links.

  • Page 17: Carburetor

    Recommended idling speed: 2 500 rpm. Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the chain stops. Do not use the cut-off saw until it has been properly adjusted or repaired. MAINTENANCE English –...

  • Page 18: Fuel Filter

    Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. • The filter cannot be cleaned but must be replaced with a new filter when it blocked.

  • Page 19: Starter

    Starter WARNING! • The recoil spring sits in its tensioned posi tion in the starter housing and can with careless handling fly out and cause personal injury. • When replacing the recoil spring or the starter cord great care should be exercised. Always wear protective glasses.

  • Page 20: Ignition System

    Ignition system IMPORTANT INFORMATION! This cut-off saw has a green coloured ignition system with integrated speed governor (order no. 506 02 73-04). The machine may only be used with such a green coloured ignition system to prevent the risk of over revving.

  • Page 21: Daily Maintenance

    Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Check that throttle components work correctly from a safety view point (throttle and starter throttle catch). 2. Clean the main filter. 3.

  • Page 22: Technical Data

    1/2 idling and 1/2 max speed. Cutting equipment Bar and chain Max. speed 14" 28 m/s at 10 000 rpm ´®z*xw6¶6Q¨ – English TECHNICAL DATA K950 Chain 93,6/5,7 ∅ 56/2,2" 38/1,5" 2 500 rpm 9 800 ± 300 Champion RCJ-7Y 0,5 (.020") Tillotson...

  • Page 23: Eu Declaration Of Conformity

    Partner Industrial Products, SE-433 81 Partille, Sweden, tel: +46-31949000, declare under sole responsibility that the cut-off saw Partner K950 Chain from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
  • Page 24 108 88 72-26 ´®z*xw6¶6Q¨ 2002W44...

Table of Contents