Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 Contents Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 3 Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 4: Introduction
Introduction BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
Page 6 Introduction Vehicle Symbol Glossary Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...
Page 7 Instrumentation Instrument cluster Turn signal and (pg. 8) Gearshift (includes wiper/washer control overdrive button) (pg. 60) (pg. 141) Headlamp control (pg. 18) DOOR THEFT AJAR NAVIGATOR RANGE FUEL RPMX1000 km/h km/h SERVICE ENGINE SUSP SOON SELECT RESET P RN BRAKE INT 2 INT 1 RESUME...
Page 8: Instrumentation
Instrumentation Clock Electronic sound system (pg. 24) (pg. 25) BASS TREB FADE PUSH ON TAPE SEEK TUNE SCAN AUTO MUTE SIDE 1 . 2 COMP SHUFF A4WD AUTOMATIC OUTSIDE TEMP MAX A/C VENT PNL FLR FLOOR FLR DEF Radio controls (pg.
Page 9 Instrumentation WARNING LIGHTS AND CHIMES DOOR THEFT AJAR NAVIGATOR RANGE FUEL RPMX1000 km/h km/h SERVICE ENGINE SUSP SELECT SOON RESET P RN BRAKE Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in FUEL this chapter for more information).
Page 10 Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1.
Page 11 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON BRAKE position.
Page 12 Instrumentation High beams Illuminates when the high beam headlamps are turned on. SecuriLock anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily THEFT illuminates when the ignition is turned to ON/START. If the light fails to illuminate, continues to flash or remains on, have the system serviced.
Page 13 Instrumentation Four wheel drive low (if equipped) Momentarily illuminates when the ignition is turned to the START RANGE position. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) Momentarily illuminates when the ignition is turned to the ON position.
Page 14 Instrumentation For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.
Page 15 Instrumentation A minimum of 22.2 L (six gallons) must be added or removed from the fuel tank in order for the gauge to instantaneously update. If less than six gallons is the change, the gauge will take between five to twenty minutes to update.
Page 16 Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T” SELECT RESET P RN appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset.
Page 17 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately.
Page 18 Instrumentation Mode control Each press of the MODE control will display a different feature as follows: MODE Fuel range. This displays the RESET approximate number of kilometers (miles) left to drive before the fuel MILES tank is empty. The indicated TO EMPTY distance to empty may be inaccurate:...
Page 19: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate.
Page 20: Controls And Features
Controls and features Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Page 21 Controls and features AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF.
Page 22 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
Page 23 Controls and features To help avoid personal injury, always use caution when in reverse and when using the reverse sensing system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
Page 24 Controls and features disable the reverse sensing system only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. The system defaults to ON every time the reverse gear is selected. Press the control to disable or enable the system.
Page 25 Controls and features A second auxiliary power point is located on the lower rear side of the console. The power point is accessible from the rear seats. CLOCK Press H to set the hour. Press M to set the minute.
Page 26 Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette (CD Changer Compatible) BASS TREB FADE PUSH ON TAPE TUNE SEEK SCAN AUTO MUTE SIDE 1 . 2 COMP SHUFF Alpine Audio System with AM/FM Stereo Cassette (CD Changer Compatible) BASS TREB FADE...
Page 27 Controls and features Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
Page 28 Controls and features With the radio on, press and hold the volume control for five seconds, until the display reads SPEED VOL #, then press: PUSH ON • to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if...
Page 29 Controls and features • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD changer • Press to select the previous TUNE disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information.
Page 30 Controls and features Scan function The scan function works in radio, tape or CD mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Page 31 Controls and features Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Page 32 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL FADE control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Page 33 Controls and features • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in tape and CD modes (if equipped).
Page 34 Controls and features Compression feature Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. The effect of the feature varies with the music content. Shuffle feature The shuffle feature operates in CD SHUFF...
Page 35 Controls and features Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information.
Page 36 Controls and features • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz •...
Page 37 Controls and features Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: • JAZZ CLUB—jazz club with clearly reflected sounds. • HALL—rectangular concert hall capacity of about 2 000 •...
Page 38 Controls and features To turn on the rear seat controls, SIDE 1-2 COMP SHUFFLE press the memory preset controls 3 and 5 at the same time. The will appear in the display. Pressing 3 and 5 at the same time again will turn the rear seat controls off.
Page 39 Controls and features Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or...
Page 40 Controls and features Seek function • In radio mode, press to find the next listenable station down - VOLUME + MODE the frequency band. • In radio mode, press to find SEEK MEMORY the next listenable station up the frequency band. •...
Page 41 Controls and features 1. Pull the lever to remove a CD tray from the magazine. 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
Page 42 Controls and features 5. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used.
Page 43 Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care •...
Page 44 Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 45: Automatic Operation
Controls and features Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed AUTO control. The EATC will only operate OUTSIDE TEMP AUTOMATIC when the vehicle is running. MAX A/C VENT PNL • FLR FLOOR FLR •...
Page 46 Controls and features Temperature selection The display window indicates the ˚ selected temperature, function AUTO (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer)
Page 47 Controls and features Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the AUTOMATIC thumbwheel or steering wheel control to cancel automatic fan speed operation.
Page 48 Controls and features • MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). To exit, press AUTOMATIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers.
Page 49 Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. OUTSIDE TEMP MAX A/C VENT PNL • FLR If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Page 50 Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 51 Controls and features Your climate controls will either be located on the rear of the center console, COOL WARM PANEL FLOOR - VOLUME + MODE SEEK MEMORY or located in the overhead console. COOL WARM PANEL FLOOR Turn the air distribution control to the desired airflow position. Turn the fan speed control to the desired position.
Page 52 Controls and features Your auxiliary A/C controls may be located in the floor console, or located in the overhead console.
Page 53 Controls and features In order for the auxiliary A/C-heater controls to function, the driver’s REAR auxiliary A/C-heater control must be set to REAR. COOL WARM PANEL FLOOR The instrument panel climate controls must be on in order for the AUTO auxiliary A/C-heater to operate.
Page 54 Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
Page 55 Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 56 Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater...
Page 57 Controls and features speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage.
Page 58 Controls and features To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or • Press and release CST/COAST to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or •...
Page 59 Controls and features To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Page 60 Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down.
Page 61 Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers.
Page 62 Controls and features Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears.
Page 63 Controls and features Radio control features • Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: NEXT • Press MEM/NEXT to select a preset station from memory. MODE In Tape mode: • Press MEM/NEXT to listen to the next selection on the tape. In CD mode: •...
Page 64 Controls and features Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.
Page 65 Controls and features One-touch moon roof (if equipped) • Press and release the rear portion of the moon roof control to open. • Press and hold (as desired) the front portion of the moon roof control to close. ROOF VENT VENT •...
Page 66 Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the compass module mounted on the center rear view mirror post. 3. Turn ignition to the ON position. 4.
Page 67 Controls and features 2. Press and hold the RESET button on the compass module until CAL indicator is displayed in the trip computer. 3. Release pressure from the RESET button. 4. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CAL indicator turns off.
Page 68 Controls and features Press the portion of the VENT control to close the power rear quarter windows. Interior Lamps Map lamps To turn on the map lamps, press the control next to each lamp. ROOF VENT VENT Rear dome lamp The dome lamp lights when: •...
Page 69 Controls and features Do not block the sensor on the backside of the inside rear view mirror since this may impair proper system performance. Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the AUTO vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when...
Page 70 Controls and features Programming 1. Prepare for programming the HomeLink Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink Universal Transceiver surface (located on your visor) while keeping the red light in...
Page 71 Controls and features To program your hand-held transmitters: • continue to hold the button on the HomeLink Universal Transceiver. • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLink Universal Transceiver Once programmed, the HomeLink Universal Transceiver can be used in...
Page 72 Controls and features 3. Press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door.
Page 73 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down •...
Page 74 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
Page 75 Controls and features POWER SIDE VIEW MIRRORS The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. MIRRORS 2.
Page 76 Controls and features Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Page 77 Controls and features CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment • Cupholders • Coin holder slots • Tissue box holder • Compact disc changer (if equipped) • Cellular phone (if equipped) Use only soft cups in the cupholder.
Page 78 Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 79 Controls and features SECURILOCK PASSIVE ANTI-THEFT SYSTEM Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to your dealership for key reprogramming.
Page 80 Controls and features Theft indicator The theft indicator in the instrument cluster will operate as follows: • When the ignition is OFF, the theft indicator will flash briefly every two seconds to indicate the anti-theft system is protecting your vehicle. •...
Page 81 Controls and features 4. Turn the ignition to OFF and remove the second coded key from the ignition. 5. Within 10 seconds of turning the ignition to OFF, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second).
Page 82 Controls and features Unlocking the doors Press this control to unlock the driver door. The interior lamps and running board lamps will illuminate. The memory mirrors/seat will also be moved to position 1, 2 or 3 depending upon which remote entry transmitter (1, 2 or 3) is used.
Page 83 Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Page 84 Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: •...
Page 85 Controls and features Illuminated entry The illuminated entry system will turn on the interior lights when the remote transmitter unlock control is pressed. The illuminated entry system will turn off the interior lights if the ignition switch is turned to the ON position, or if the remote transmitter lock control is pressed, or after 25 seconds of illumination.
Page 86 Controls and features 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6.
Page 87 Controls and features 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to OFF. The horn will chirp once to confirm the procedure is complete.
Page 88 Controls and features If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control within five seconds of step one. 7 8 9 0 3. Press 7/8 control and 9/0 control at the same time within five seconds of step 2.
Page 89: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 90: Seating And Safety Restraints
Seating and safety restraints Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 91 Seating and safety restraints Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Page 92 Seating and safety restraints Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to three programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat to the desired position using the seat controls.
Page 93 Seating and safety restraints CLIMATE CONTROL SEATS (if equipped) To operate the climate control seats the engine must be running. • Slide the control to to heat the seatback and the seat cushion. • Slide the control to to cool the seatback and the seat cushion.
Page 94 Seating and safety restraints • There is a filter located under both front seats and can be accessed from the second row seat. Move the front seat all the way forward and up to ease access.
Page 95 Seating and safety restraints To remove climate control seat air filter: • Remove key from ignition. • Push on the outside rigid edge of the air filter at the center and rotate downward once tab is released. Remove filter. To install climate control seat air filter: •...
Page 96 Seating and safety restraints Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that the headrest is in the down position and no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
Page 97 Seating and safety restraints Returning the seat to upright Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1. Rotate the closeout panel onto the seatback and press the black control (adjacent to the green control) to lock.
Page 98 Seating and safety restraints the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter. The third row seat may be removed from the vehicle for additional cargo space. Accessing the third row seat Your vehicle is equipped with an easy entry second row seat feature which allows ready access to the...
Page 99 Seating and safety restraints Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor.
Page 100 Seating and safety restraints • Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. • The seatback will latch into place. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches.
Page 101 Seating and safety restraints • When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor. 3. Locate the seat belt anchor tongue in the plastic housing on the floor. 4.
Page 102 Seating and safety restraints 5. Lift latch up and out of floor tub to upright position using the strap on the latch. 6. Pull down support bar and push into floor latch. To return seat to seating position: 1. Hold seat and pull support bar from floor latch. 2.
Page 103 Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided.
Page 104 Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 105 Seating and safety restraints When to use the automatic locking mode • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
Page 106 Seating and safety restraints How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Page 107 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 108 Seating and safety restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button down and slide the height adjuster down.
Page 109 Seating and safety restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition switch illuminates1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds. The driver’s safety belt is buckled The safety belt warning light and while the indicator light is...
Page 110 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... Crashes are rare 36 700 crashes occur every day. The more we events drive, the more we are exposed to rare events, even for good drivers.
Page 111 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Page 112 Seating and safety restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
Page 113 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity.
Page 114 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer.
Page 115 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 116 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 117 Seating and safety restraints The RCM (restraints control module) monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 118 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Page 119 Seating and safety restraints by the collision will be inflated, even if the respective seat is not occupied. The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 120 Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
Page 121 Seating and safety restraints Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
Page 122 Seating and safety restraints Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 123 Seating and safety restraints Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 124 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 125 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 126 Seating and safety restraints 5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the buckle while pushing down with your knee on the child seat.
Page 127 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln/Mercury dealer. All second row and third row passenger side seating positions (if equipped) have a fabric strap installed near the bottom of the rear face of the seatback.
Page 128 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 129 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the gearshift is in P (Park). 4. Make sure the parking brake is set. 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 130: Starting The Engine
Starting DOOR THEFT AJAR NAVIGATOR RANGE FUEL RPMX1000 km/h km/h SERVICE ENGINE SUSP SELECT SOON RESET P RN BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Page 131 Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
Page 132 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 133 Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 134: Driving
Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock BRAKE brake system is disabled and normal...
Page 135 Driving Parking brake with auto-release Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and BRAKE remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 136 Driving If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy.
Page 137 Driving Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Page 138 Driving The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Page 139 Driving To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 140 Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1.
Page 141 Driving Driving with a 4–speed automatic transmission Your vehicle’s automatic transmission is equipped with a special shift strategy that insures maximum heater performance during cold weather operation. When ambient temperature is –5° C (23° F) or below and the engine coolant temperature is below 38°...
Page 142 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 143 Driving Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide...
Page 144 Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired.
Page 145 Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
Page 146 Driving Shifting to A4WD Move the 4WD control back to A4WD at a stop or at speeds up to A4WD 88 km/h (55 mph). Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road.
Page 147 Driving Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain.
Page 148 Driving reduces strain on the engine and the possibility of stalling. When descending a steep hill, avoid sudden braking. Shift to a lower gear when added engine braking is desired. When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load.
Page 149 Driving Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc.
Page 150 Driving Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations.
Page 151 Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo.
Page 152 Driving GCWR (Gross Combined Weight Rating)/Trailer weights Rear axle Maximum GCWR - Trailer weight range Engine ratio kg (lbs.) (0-maximum) - kg (lbs.) 4x2 with 17 inch wheels 6 577 0-4 037 5.4L-4V 3.73 (14 500) (0-8 900) 4x4 with 17 inch wheels 6 350 0-3 674 5.4L-4V...
Page 153 Driving Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle.
Page 154 Driving If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications.
Page 155 Driving Recreational towing (all wheels on the ground) An example of recreational towing would be towing your vehicle behind a Motorhome. Follow these guidelines if you have the need for recreational towing your vehicle with all four wheels on the ground. These guidelines are designed to ensure that your transmission is not damaged.
Page 156 Driving Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper.
Page 157: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, it is found in the Roadside Assistance book in the glove compartment.
Page 158: Roadside Emergencies
In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–894–2582).
Page 159 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 160 Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard...
Page 161 Roadside emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Audio Clock, Overhead Trip Computer, Electronic Automatic Temperature Control (EATC), Powertrain Control Module (PCM), Cluster, Navigation Cigar Lighter, OBD-II Scan Tool Connector...
Page 162 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Cluster, Overhead Trip Computer, Compass, Steering Sensor, Brake Shift Interlock Solenoid, Air Suspension Module, GEM Module, Heated Mirror, Rear Defroster, Reverse Sensing System, Automatic Park Brake Release Aux A/C Blower Relay, Console Blower Remote Entry Module, Cell Phone, Clock, GEM Module, Navigation —...
Page 163 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Starter Relay, Fuse 20, Digital Transmission Range Selector Air Bag Module, EATC, EATC Blower Relay, Feeds Fuse 7 Electrochromic Mirror, Aux A/C, Heated Seats, Trailer Tow Battery Charge, Turn/Hazard Flasher, Console Blower Door Actuator, 4x4 Clutch Relay, 4 Wheel Anti-Lock Brake System (4WABS) Module...
Page 164 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 165 Roadside emergencies The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 20A * Power Point 30A* Powertrain Control Module 30A* Headlamps/Autolamps 20A* Console Powerpoint 20A* Trailer Tow Backup/Park Lamps 15A* Parklamps/Autolamps, Feeds Passenger Compartment Fuse 18 20A* Horn...
Page 166 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 30A** 4x4 Shift Motor & Clutch 40A** Climate Control Front Blower — Not Used 30A** Passenger Power Seat, Passenger Seat Lumbar 30A** Trailer Tow Electric Brake 50A** Air Suspension Compressor 30A** Heated Seats/CCS 40A**...
Page 167 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating — Powertrain Control Module Relay — Not Used — Powertrain Control Module Diode — A/C Clutch Diode — Automatic Park Brake Release Diode Delayed Accessory (Power Windows, Flip Windows, Radio, Moonroof) —...
Page 168 Roadside emergencies Removing the jack handle 1. Open the hood. 2. Unsnap the end of the handle that is retained by the clip on the top of the windshield washer bottle. 3. Unsnap the shaft of the handle from the two retaining clips attached to the top of the radiator shroud.
Page 169 Roadside emergencies Stowing the spare tire 1. Lay the tire on the ground with the outboard side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle.
Page 170 Roadside emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine OFF. 3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations.
Page 171 Roadside emergencies 7. Turn OFF the air suspension switch. 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the...
Page 172 Roadside emergencies • Front (4x4) • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
Page 173 Roadside emergencies 12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Stow the flat tire. Refer to Stowing the spare tire. 14. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive.
Page 174 Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4.
Page 175 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 176 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 177 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 178 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 179: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 180 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.
Page 181 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V V8 engine 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8.
Page 182 Maintenance and care 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5.
Page 183 Maintenance and care • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1.
Page 184 Maintenance and care Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide.
Page 185 Maintenance and care If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry, this may cause the brakes to fail.
Page 186 Maintenance and care ENGINE COOLANT Checking engine coolant Your engine’s cooling system has been factory-filled with a 50/50 mixture of distilled water and Ford G05 Engine Coolant (yellow in color) per ford specification WSS-M97B51–A1. A 50/50 mixture of distilled water and Ford G05 Engine Coolant provides: •...
Page 187 Maintenance and care • Refer to the scheduled maintenance guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Page 188 Maintenance and care Do not put engine coolant in the windshield washer fluid reservoir. If engine coolant is sprayed onto the windshield, it could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir, until the coolant is at the “cold fill level”...
Page 189 Maintenance and care Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A. Use of a recycled engine coolant which does not meet the Ford specification may harm engine and cooling system components.
Page 190 Maintenance and care • decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
Page 191 Maintenance and care Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution.
Page 192 Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and...
Page 193 Maintenance and care 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7.
Page 194 Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter.
Page 195 Maintenance and care If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water.
Page 196 Maintenance and care Battery posts, terminals and related accessories contain lead and lead compunds. Wash hands after handling. Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance.
Page 197 Maintenance and care AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers in the Capacities and specifications chapter.
Page 198 Maintenance and care 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated.
Page 199 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
Page 200 Maintenance and care U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Page 201 Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure •...
Page 202 Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Page 203 Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains: •...
Page 204 Maintenance and care Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle.
Page 205 Maintenance and care splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling.
Page 206 Maintenance and care octane ratings may degrade performance. We do not recommend the use of gasolines labeled as “Premium” in high altitude areas that are sold with octane ratings of less than 91. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.
Page 207 Maintenance and care Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine.
Page 208 Maintenance and care If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Page 209 Maintenance and care For consistent results when filling the fuel tank: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling (more than three clicks would overfill the tank).
Page 210 Maintenance and care Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 211 Maintenance and care • Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy.
Page 212 Maintenance and care • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system.
Page 213 Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: •...
Page 214 Maintenance and care 3. At the back of the headlamp, remove the headlamp assembly retainers by pushing rearward and pulling up. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors. 5. Rotate the bulb cover counterclockwise and remove. 6.
Page 215 Maintenance and care 8. Without turning, carefully pull the bulb out of the headlamp assembly. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 216 Maintenance and care 5. Release clip and disconnect the electrical connector from the bulb socket. 6. Rotate the bulb socket counterclockwise and remove. 7. Pull the bulb straight out of the socket and push in the new bulb. 8. To complete installation of the parking lamp/turn signal assembly, follow the removal procedures in reverse order.
Page 217 Maintenance and care Replacing tail lamp bulbs 1. Open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly. 3. Carefully pry the lamp assembly away from the vehicle to expose the bulb socket. 4.
Page 218 Maintenance and care 3. Rotate the bulb socket counterclockwise counterclockwise and remove. 4. Pull bulb straight out of socket and push in the new bulb. 5. To complete installation, follow the removal procedure in reverse order. Replacing license plate lamp bulbs To change the license plate bulbs: 1.
Page 219 Maintenance and care Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
Page 220 Maintenance and care AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant.
Page 221 Maintenance and care Turning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown. Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the bubble level and the vertical adjustment screw.
Page 222 Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
Page 223 Maintenance and care recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line.
Page 224 Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning.
Page 225 Maintenance and care hot wax treatments used by commercial car washes. Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches.
Page 226 Maintenance and care the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label. Regular cleaning of your leather upholstery helps maintain its resiliency and color.
Page 227: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS Component 5.4L 4V V8 engine Air filter element FA-1634 Battery (standard) BXT-65-650 Fuel filter FG-986B Oil filter FL-820-S PCV valve EV-233 Spark plugs* AWSF-32P * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Page 228: Capacities And Specifications
Capacities and specifications Fluid Ford Part Application Capacity Name Engine coolant Premium Engine without aux rear 24.1L Coolant heat (25.5 quarts) with aux rear 26.4L heat (27.9 quarts) Front axle Motorcraft SAE 4 x 4 vehicles 1.8-2.0L lubricant 75W-90 (3.5-3.7 pints) Premium 4x4 Front Axle Lubricant...
Page 229 Capacities and specifications amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range. Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.
Page 230 Capacities and specifications Ford part Ford part Ford Item name number specification Engine coolant Ford Premium E2FZ-19549-AA ESE-M97B44-A Engine Coolant (in Canada, Motorcraft CXC-10) Engine oil Motorcraft SAE XO-5W-30-QSP WSS-M2C153-G 5W-30 Super with API Premium Motor Certification Mark 4x4 front wheel High E8TZ-19590-A ESA-M1C198-A...
Page 231 Capacities and specifications Ford part Ford part Ford Item name number specification Windshield Ultra-clear C9AZ-19550-AC ESR-M17P5-A washer fluid Windshield Washer Concentrate Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
Page 232 Capacities and specifications ENGINE DATA Engine 5.4L 4V V8 engine Cubic inches Required fuel 91 octane Firing order 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system Coil on plug Compression ratio 9.5:1 VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in) 4x4 mm (in) (1) Overall length 5 202.0...
Page 233 Capacities and specifications...
Page 234: Certification Label
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. Administration Regulations require DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG that a Certification Label be affixed FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL to a vehicle and prescribe where the MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE Certification Label may be located.
Page 235: Customer Assistance
• protection against repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs.
Page 236: Customer Assistance
Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership.
Page 237 Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
Page 238 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
Page 239 • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 240 Customer assistance • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review.
Page 241 Customer assistance You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Page 242 Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
Page 243 FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 244 Customer assistance Comfort and convenience Cabin air filter Cargo nets (Floor mount) Cargo organizers Cargo trays Engine block heaters Tire step Travel equipment Ashtray, rear seat Automatic headlamp system with DRL Daytime running lights (DRL) Factory luggage rack Factory luggage rack adaptors Heavy-duty battery Raised cross bars Raised cross bar adaptors...
Page 245 Customer assistance Lubricants and oils Molded vinyl floor mats Rear air deflectors Side window air deflectors Spare tire lock Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
Page 246 Customer assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio: Make checks payable to: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST, for credit card holders only Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to...
Page 247: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 248 Index Auxiliary power point ....23 Axle Accessory delay ......73 lubricant specifications ..228, 231 Air bag supplemental refill capacities ......226 restraint system ....112, 116 traction lok ......137 and child safety seats ....114 description ......112, 116 disposal ......116, 119 driver air bag ....114, 117 Battery ........193 indicator light .....9, 116, 118 acid, treating emergencies ..193...
Page 249: Index
Index Cellular telephone (see your Cruise control Cellular Phone Guide) ....76 (see Speed control) ....54 Certification Label ....233 Customer Assistance ....156 Ford accessories for your Child safety restraints ....120 vehicle ........241 child safety belts ....120 Ford Extended Child safety seats ....120–121 Service Plan ......234 in front seat ......122 Getting assistance outside...
Page 250 Index description ......143 driving off road .......145 Emergencies, roadside electronic shift ....21, 144 jump-starting ......172 indicator light ......12 preparing to drive your Emission control system ..210 vehicle ........138 Engine ........231 Fuel ..........202 check engine/service calculating fuel economy ..207 engine soon light ......8 cap ...........206 cleaning ........222 capacity ........226...
Page 251 Index odometer ........15 speedometer ......14 tachometer ........15 Ignition .........53, 231 trip odometer ......15 Infant seats GAWR (see Safety seats) .....120–121 (Gross Axle Weight Rating) ..148 Inspection/maintenance calculating .......150 (I/M) testing ......211 definition .........148 Instrument panel driving with a heavy load ..148 cleaning ........224 location ........148 cluster ........8, 224...
Page 252 Index interior lamps ....67, 218 Mirrors .........68 replacing bulbs ..212, 214–217 automatic dimming rearview mirror ........67 Lane change indicator fold away ........75 (see Turn signal) ......53 heated ........75 Liftgate ........77 programmable memory ....84 side view mirrors (power) ..74 Lights, warning and indicator ..8 air bag ..........9 Moon roof ........64 air suspension ......137...
Page 253 Index SecuriLock passive anti-theft system ....78–79 Radio ..........25 Servicing your vehicle ....178 Relays ........158, 166 Snowplowing .........3 Remote entry system ...80–81 Spark plugs, illuminated entry ......84 specifications .....226, 231 locking/unlocking doors ...81 Special notice ........3 panic alarm .......81 ambulance conversions ....3 replacement/additional utility-type vehicles ....3 transmitters .......83...
Page 254 Index Transmission ......139 fluid, checking and adding (automatic) ......191 Warning chimes .....12–13 fluid, refill capacities ....226 Warning lights (see Lights) ..8 lubricant specifications ..228, 231 Washer fluid ......184 Trip odometer ......15 Water, Driving through .....147 Turn signal ......10, 53 Windows power .........72 rear wiper/washer .....60 Vehicle dimensions ....231...
Page 256: Filling Station Information
Filling station information Item Information Required fuel-5.4L 4V V8 engine Unleaded fuel only - 91 octane Fuel tank capacity 113.6L (30 gallons) Tire size and pressure Refer to the Certification Label inside of driver’s door. Hood release Pull handle under the left side of the instrument panel.
Page 257 Filling station information an automatic transmission application requiring MERCON may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage. Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.

This manual is also suitable for:

Navigator 2001

Lincoln Navigator 2000 Owner's Manual

Quick Links

Related Manuals for Lincoln Navigator 2000

Summary of Contents for Lincoln Navigator 2000

This manual is also suitable for:

Table of Contents