Page 1 Table of Contents Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD Rear seat controls Rear seat entertainment system Navigation system Climate Controls Rear passenger climate control Rear window defroster Lights Headlamps...
Page 2: Table Of Contents
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Air suspension Transmission operation Vehicle loading Trailer towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing...
Page 3: Table Of Contents
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications Accessories Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 4: Introduction
State of California to cause cancer and birth defects or other reproductive harm. CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
Page 6 Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Page 7 Introduction Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF. Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Your vehicle is not equipped with a snowplowing package.
Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
Page 9 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 10: Instrument Cluster
Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 Instrument Cluster or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing dealership.
Page 12 Instrument Cluster Engine coolant temperature: Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Refer to Engine coolant in the Maintenance and Specifications chapter. Never remove the coolant recovery cap while the engine is running or hot.
Page 13 Instrument Cluster O/D off: Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter. If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur. AdvanceTrac (if equipped): Illuminates when the AdvanceTrac system is active.
Page 14: Gauges
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
Page 15 Instrument Cluster Trip odometer: Registers the kilometers (miles) of individual journeys. Press and release the message center INFO button until “TRIP” appears in the display (this represents the trip mode). Press and hold the RESET button for three seconds to reset. Tachometer: Indicates the engine speed in revolutions per minute.
Page 16: Entertainment Systems
Entertainment Systems Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bass output.
Page 17 Entertainment Systems right and left speakers. Press BAL then press SEL to shift sound to the left or right FADE: Allows you to shift speaker sound between the front and rear speakers. Press FADE then press SEL to shift the sound to the rear or the front 5.
Page 18 Entertainment Systems FF (Fast Forward): Works in tape and CD modes. In the tape mode, tape direction automatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 10. MUTE: Press to mute the playing media.
Page 19 Entertainment Systems 11. AUTOSET: Press to set first six strong stations into AM, FM1 or FM2 memory buttons; press again to return to the original preset stations. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 20 Entertainment Systems control for five seconds (with the radio on). Press SEL to increase /decrease volume compensation levels. The selected level will appear in the display. 17. TAPE: Press to begin tape play. Press during fast forward or rewind to stop fast forward or rewind function.
Page 21 TEXT: TEXT is only available when equipped with Satellite radio. Your Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Lincoln dealer. Detailed Satellite instructions are included with the dealer installed kit.
Page 22 Entertainment Systems 4. Mute: Press to MUTE playing media; press again to return to playing media 5. Eject: Press to eject a CD. Press and hold to eject all loaded discs. 6. Bass: Press BASS; then press to decrease/increase the bass output. Treble: Press TREB;...
Page 23 11. SAT (if equipped): Your Audiophile radio comes equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your Lincoln dealer. Detailed satellite instructions are included with the dealer installed kit. 12. AM/FM: Press to select AM/FM frequency band.
Page 24 CAT: CAT is only available when equipped with Satellite Radio. Your Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Lincoln dealer. Detailed Satellite instructions are included with the dealer installed kit.
Page 25: Rear Seat Controls
Entertainment Systems REAR SEAT RADIO CONTROLS (IF EQUIPPED) If your vehicle is equipped with a - VOLUME + front row console, then it is also MODE equipped with rear seat radio controls. This feature allows front and middle seat passengers to listen SEEK MEMORY to different media sources (radio,...
Page 26 Entertainment Systems • Dual Play mode may also be activated by pressing memory presets 2 and 4 simultaneously on the front audio controls. The rear speakers mute and rear seat passengers have audio (for their selected media) available through their headphones. To adjust the volume The volume control allows the rear seat passengers to adjust the volume level of the audio system.
Page 27 Entertainment Systems The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones. SINGLE PLAY illuminates in the radio display and the fade control is enabled, signaling that Dual Play mode has been deactivated.
Page 28 Entertainment Systems Seek function • In radio mode, press to find - VOLUME + MODE the next listenable station down the frequency band. • In radio mode, press to find SEEK MEMORY the next listenable station up the frequency band. •...
Page 29 Entertainment Systems CASSETTE/PLAYER CARE • Use only cassettes that are 90 minutes long or less. • Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. •...
Page 30 Entertainment Systems AUDIO SYSTEM WARRANTY AND SERVICE Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. Whenever a warning is received, the radio volume will be lowered to a volume that will allow the tones to be heard. The radio volume will return to the previous level after the warning goes away.
Page 31 Entertainment Systems 2. PLAY/PAUSE control Press to playback or pause the DVD. 3. DIM control Adjust to increase (+) or decrease (-) the amount of brightness on the screen. 4. ENTER control Press to select the function pointed to within the active menu. May also be used by some user interactive discs during movie play.
Page 32 Entertainment Systems • Press the PREV control to move the cursor one position downward NEXT PREV • Press the REV control to move the cursor left one position NEXT PREV • Press the FWD control to move the cursor right one position NEXT PREV Next/Previous control...
Page 33 Entertainment Systems CD play mode Press NEXT during CD play to advance to the next track. If you NEXT press NEXT during the last track, PREV the system will wrap around to the first track and begin play. Slow play mode To enter slow play mode, press the PLAY/PAUSE control.
Page 34 Entertainment Systems Remote control SEEK DISP MODE MEMORY 1. REWIND control Press to reverse the direction of the DVD movie. 2. FAST FORWARD control Press to advance the direction of the DVD movie. 3. PLAY/STOP control Press to play or stop the DVD movie. 4.
Page 35 Entertainment Systems In stop mode, press to change to a different playing media (e.g. AM, FM, CD . . . ) 8. VOLUME control Press to increase (+) or decrease (-) volume level. Battery replacement Batteries are supplied with the remote control unit.
Page 36 Entertainment Systems To install the batteries, lightly press down on the top of the left earpiece and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct (+) and (-) orientation.
Page 37 Entertainment Systems Liquid Crystal Display (LCD) flip-down screen The screen rotates down to view and into the housing to store when not in use. Be sure the screen is latched into the housing when being stored. 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen. 2.
Page 38 Entertainment Systems Rear Seat Entertainment DVD System protection circuits High temperature sensor circuit • Excessively high temperatures may cause damage to the DVD player. • When the temperature of the DVD player becomes too hot, the high temperature sensor circuit stops machine operation. DVD/CD HOT will illuminate in the radio display.
Page 39 Entertainment Systems Inserting a CD/DVD Inserting a CD/DVD into the DVD player automatically turns the power ON and playback should begin. The counter is automatically reset to 0:00:00. Removing a CD/DVD 1. Press the STOP/EJECT control to stop playback. 2. Press the STOP/EJECT control again to eject the CD/DVD. If the CD/DVD is not removed within the allotted time, the system will pull the CD/DVD back into the system for safety purposes.
Page 40 Do not attempt to service, repair or modify the Rear Seat Entertainment DVD System. See your Ford or Lincoln Mercury dealer. Do not insert foreign objects into the DVD compartment. The front glass on the liquid crystal display (LCD) flip-down screen may break when hit with a hard surface.
Page 41 Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 42 Entertainment Systems Care and service of the DVD player Environmental extremes DVD players that are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability. To avoid these outcomes, whenever possible avoid exposing your DVD player to: •...
Page 43: Navigation System
Use of these products may damage your system. LINCOLN NAVIGATION SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Lincoln Navigation System which allows you to listen to the radio, play CDs and also navigate the vehicle using a navigation DVD.
Page 44 Entertainment Systems 1. VOL-PUSH: Press to turn the system ON/OFF. Turn to adjust the audio volume level. 2. AUDIO: Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP: Press to enter map mode and view your current vehicle position on the map.
Page 45 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock.
Page 46 Entertainment Systems To play a previously loaded CD: 1. Ensure that the vehicle ignition is on. 2. Press AUDIO. 3. Press CD to select a CD which is already loaded. (NO CD will appear in the display if there are no CDs loaded into the system). Use the controls (1–6) to select the desired CD.
Page 47 Voice activated commands (if equipped) Your Lincoln Navigation System (LNS) may be equipped with a voice activated feature which allows you to “speak” certain commands to the system. Speaking clearly will help to ensure that the system correctly responds to your commands.
Page 48 Entertainment Systems The voice activated command feature will not operate if a map DVD is not inserted into the navigation DVD unit. At any time, you may say these commands to change modes: • Radio • Audio on • AM •...
Page 49 Entertainment Systems While in navigation map mode, the following commands are available: • Zoom in • Zoom out • Minimum scale • Maximum scale • North up • Change North up • Heading up • Change heading up • Map direction •...
Page 50 Entertainment Systems • Italian food • Japanese restaurant • Japanese food • Mexican restaurant • Mexican food • Seafood restaurant • Seafood • Other restaurant • Other food • Shopping • Shopping mall • Grocery store • Airport • Bus station •...
Page 51 • Radio help • Disc help Audio mode Your Lincoln Navigation Audio System has many features including a full range of audio functions. To access these functions, press AUDIO on the main bezel. This will take you into audio mode.
Page 52 Entertainment Systems To adjust the navigation voice output level, select the NAV MENU button via the map screen. Speed compensated volume (SCV) With this feature, radio volume changes automatically with vehicle speed to compensate for road and wind noise. To engage the SCV feature: 1.
Page 53 Entertainment Systems The recommended level for the speed compensated volume is from level 1 through level 3. When activated, level 1 is the minimum setting and level 7 is the maximum setting. AM/FM select The AM/FM control works in radio, CD and navigation modes. AM/FM select in radio mode Press AM/FM1/FM2 to switch between AM/FM1/FM2 memory preset stations.
Page 54 Entertainment Systems Bass : Allows you to increase or decrease the audio system’s bass output. Treble : Allows you to raise or lower the audio system’s treble output. Fade : Allows you to adjust sound between the front and rear speakers.
Page 55 Entertainment Systems Setting memory preset stations The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). 1.
Page 56 Entertainment Systems Starting autoset memory preset 1. Select a frequency band using SOUND AM/FM1/FM2. SEEK TUNE SCAN PRESET SCAN AUTO SET TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3 107.9 2. Press AUTO SET. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Page 57 Entertainment Systems Radio data system (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations such as station call letters, program type, etc. When in FM mode, press RDS to activate/deactivate. Traffic function Select TRAFFIC for traffic SOUND information broadcast from certain...
Page 58 Entertainment Systems Ensure that the RDS function is turned on. Press PTY to turn the feature on/off. To set/change PTY: SOUND SEEK TUNE Ensure that the RDS function is AUTO SET turned on. SCAN PRESET SCAN Press SET PTY to select from the TRAFFIC SET PTY INFO...
Page 59 Entertainment Systems Satellite ready capability (if equipped) Your Lincoln navigation system may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Lincoln dealer. Detailed Satellite instructions are included with the dealer installed kit.
Page 60 Entertainment Systems Press CD. CD play will begin where it stopped last. Loading a CD: 1. Press CD OPEN CLOSE on the bezel. 2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number. The indicator light will blink slowly at first, then quickly, signaling the system is ready.
Page 61 Entertainment Systems Track Press to advance to the next/previous track. Rewind/fast forward in CD mode Press to reverse or advance ) in the current CD track. Scan feature in CD mode Press SCAN to hear a brief sampling of all tracks on the current CD. Press again to disengage and remain with the current track.
Page 62 Entertainment Systems Compression feature The compression feature works in CD mode and boosts more quiet music and lowers louder music to minimize the need for volume adjustments. When in CD or CDDJ mode, press COMPRESS to engage or disengage the compression feature. Pause In CD mode, press PAUSE to pause the current track.
Page 63 Entertainment Systems Once pressed, the current map display will appear on the screen showing the current vehicle location. Zoom control When ’Zoom’ is pressed, the scale indicator is shown on the screen. The scale markings are: 1/32, 1/16,1/4, 1/8, 1/2, 1, 2, 4, 8, 16, 32, 64, 128 miles.
Page 64 Entertainment Systems If home has been previously programmed in the “Nav Menu”, the home icon (house) will appear on the screen and is able to be selected as a destination. To delete POI icons from the map, touch the map again and press the POI off button.
Page 65 Entertainment Systems If the avoid point is enlarged to an avoid area, it will appear on the screen as a shaded box. Way point symbol — Indicates the location of a way point (locations you wish to visit in route to your ultimate destination) on the map.
Page 66 Entertainment Systems Once pressed, the Navigation Menu will display showing the following options: • Route Options/Preferences • Navigation Set Up • Display Options • Stored Locations • On Route Scroll • Voice Guidance/Volume Depending upon whether or not a route is active will determine if route options/route preferences is contained on the Navigation Menu.
Page 67 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Route preferences After entering a destination, the Route options will appear on the...
Page 68 Entertainment Systems Average speed settings Allows you to set approximate speeds you drive. These speeds enable the navigation system to aid in calculating timing for routes. Quick POI (Point of Interest) Allows you to change the Quick POI menu settings. Select the desired Quick POI (Gas, ATM, etc.) and then press ’List Categories’...
Page 69 Entertainment Systems Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map. Press “Position” to reposition the vehicle location. Press the screen to scroll the map to the desired location and press OK to confirm.
Page 70 Entertainment Systems • Time to destination (Show or Hide) Stored locations The Stored locations screen will allow you to choose from destinations that have been saved into the navigation system. In this screen, you can select from Memory Points, Special Memory Points, Home, Avoid Area, Destination and Way Point, or Previous Destination.
Page 71 Entertainment Systems On route scroll The system automatically scrolls through the entire planned navigation route either forwards or backwards. To activate, press the arrow buttons at the bottom left of the map screen. Voice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts.
Page 72 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock.
Page 73 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Destination entry Selecting a destination Press DEST to set a destination.
Page 74 Entertainment Systems Search area The mapped areas covered by your map DVD are reflected in the Search Area map that is displayed on the Destination Entry screen. Your navigation system uses a regional search area. This area is the area from which navigational directions will be used.
Page 75 Entertainment Systems Deleting previous destination • Press “Delete”. The list of previous destinations is displayed showing “Delete Previous Destination” at the top of the screen. • Select (touch) the entry to be deleted. The item details will be listed. • Press YES to confirm the deletion.
Page 76 Entertainment Systems Adding a memory point • Once in the Store Memory Point Menu, press ADD. • Select (touch) the desired menu item. • Enter/select any required details. The new point will be added to the stored list of memory points. To give the new memory point a name: •...
Page 77 Entertainment Systems Choosing from the icon list After choosing ICON to edit, 15 normal and three audible icons will be displayed. Press the icon you wish to use. The normal icons will be displayed on the map to indicate the map location identified with that icon.
Page 78 Entertainment Systems Home To set home for the first time: • Press MAP. • Press “Nav. Menu”. • Press “Stored Locations.” • Press “Home”. • Press “Add”. Set home by selecting the correct address, POI, Previous destination, or selecting from the map. To view home, press the home icon (house) on the Destination Entry screen.
Page 79 Entertainment Systems Adding a home location • Select the desired menu item you SET HOME wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). • Enter the required details. • Press OK to set the home position.
Page 80 Entertainment Systems Freeway Entrance/Exit Select “Freeway Entrance/Exit” from the second page of the Destination Entry menu. Follow these steps: 1. Enter freeway name— Enter the freeway name using the keyboard. Press “List” to select a freeway from those displayed. To enter numbers in the freeway name, press “Sym”.
Page 81 Entertainment Systems Special memory points There are five possible memory points that you can set. To set a memory point: • Press MAP. • Press “Nav Menu”. • Press “Stored locations”. • Press “Special Memory Point”. • Select “Add” and input destination. •...
Page 82 Entertainment Systems Adding (storing) a destination or way point • Once a destination is entered, press ADD to store the location. The Store Dest. & Way Point menu is displayed. • Select whether you want to store an Address, Point of Interest or Previous Destination.
Page 83 Entertainment Systems Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display.
Page 84 Entertainment Systems Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “Next”...
Page 85 Entertainment Systems Route interruptions In the course of your destination, you may decide to temporarily leave your planned route for gas, food, etc. If you turn off the ignition, the option to continue the route guidance will be displayed when the ignition is turned on again.
Page 86 Entertainment Systems Listing areas to avoid You can list all areas noted as “avoid”. • Press “Nav Menu”. • Press “Stored locations”. • Press “Avoid area”. • Press LIST to view all previously stored selections. • Select the desired one. The map screen will be displayed, showing the location and address of the selected area.
Page 87 To access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
Page 88 English, French, or Spanish. DVD interaction (if equipped) Your vehicle may be equipped with a DVD player. Your Lincoln Navigation System (LNS) will interact with your DVD player, providing you access and messages to the status of the system.
Page 89 Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion. Give full attention to driving and to the road.
Page 90 Ford or Lincoln Dealer. Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 91 Entertainment Systems Accordingly, the database may contain inaccurate or incomplete information due to the passage of time, changing circumstances, and due to the nature of the sources used. The database does not include or reflect information on neighborhood safety, law enforcement, emergency assistance, construction work, road or lane closures, vehicle or speed restrictions, road slope or grade, bridge height, weight or other limits, road or traffic conditions,...
Page 92 Entertainment Systems Limited GPS reception System performance may be adversely affected if GPS reception is interrupted or interference occurs over a distance of several miles. The following are possible causes for GPS reception being interrupted. If the vehicle is: • in multi-story parking garages •...
Page 93 Entertainment Systems The navigation system utilizes a database stored in a special format on a DVD. It is recommended always to use the latest update of this map DVD. • The navigation system will only work with DVDs specifically intended for your navigation system.
Page 94: Climate Controls
Climate Controls Climate Controls DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM DUAL AUTO 1. A/C control: Uses outside air to cool the vehicle. Press to turn on/off in all modes except 2. Recirculation control: Used to manually enable or disable the operation of recirculated air in all modes except Defrost.
Page 95 Climate Controls control of their individual temperature settings (dual zone control). Press to enable dual zone mode, press again to return to single zone. : Distributes outside air through the windshield defroster vents. : Distributes outside air through the windshield defroster vents and floor vents.
Page 96 Climate Controls Manual override controls: Allows you to manually determine where airflow is directed. To return to fully automatic control, press AUTO. OPERATING TIPS • To reduce fog build up on the windshield during humid weather, place the air flow selector in the position.
Page 97 Climate Controls AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with auxiliary climate controls. These allow the front or rear seat passengers to control airflow direction, temperature and fan level of the rear compartment to quickly heat or cool the vehicle.
Page 98: Rear Window Defroster
Climate Controls Rear auxiliary controls (if equipped): Once the front auxiliary control is set to REAR, the rear seat passengers may use the rear auxiliary controls in the floor console to make the desired adjustments. 1. Temperature control: Determines temperature levels. If the main climate control system is cooling in MAX A/C or mode,...
Page 99: Lights
Lights Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Foglamp control The headlamp control also operates the foglamps. The foglamps can be turned on when the headlamp control is in the positions and the high beams are...
Page 100 Lights Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Page 101 Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to prevent the interior lights from illuminating...
Page 102: Turn Signal Control
Lights 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line.
Page 103: Bulb Replacement
Lights INTERIOR LAMPS Front row map lights (if equipped) To turn on the map lights, press the rear edge of the light. Rear dome lamp The dome lamp lights when: • any door is opened (and switch is in middle position). •...
Page 104 Lights Function Number of bulbs Trade number Headlamps 9006 (low-beams) Headlamps (hi-beam) 9005 Front park/turn lamps 3157 AK (amber) Front sidemarker 194 AK (amber) Foglamps Dome/map lamps Turn/tail/brake lamps 3157K Approach lamps Mirror turn signal 906 (amber) lamps Liftgate lamp Backup lamp 3157K License lamp...
Page 105 Lights Replacing headlamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the hood. 3. At the back of the headlamp lens, remove the three headlamp assembly retainers bolts. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors.
Page 106 Lights Replacing HID headlamp bulbs (if equipped) The low beam headlamps on your vehicle use a “high intensity discharge” source. These lamps operate at a high voltage. The bulb is NOT replaceable. When the bulb is burned out, the lamp assembly must be replaced by your dealer or a qualified technician.
Page 107 Lights 1. Make sure the headlamp switch is in the OFF position. 2. Disconnect the electrical connector from the foglamp bulb. 3. Rotate the foglamp bulb counterclockwise and remove from the foglamp (the rear side of the foglamp is shown). 4.
Page 108 Lights Replacing back-up lamp bulbs The back-up lamp bulbs are located behind the liftgate trim panels. To change the back-up lamp bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the liftgate trim panel by removing the retaining nuts to expose the bulb socket.
Page 109 Lights 3. Pull the lamp assembly straight out (it will snap out of a plastic retaining grommet). 4. Turn the wire harness counterclockwise to remove it from the lamp. 5. Pull out the bulb and replace it with a new one. 6.
Page 110 Lights High-mount brakelamp To change the high-mount brakelamp bulbs: 1. Remove the two screws holding the lamp assembly in place. 2. Pull the lamp assembly straight out. 3. Remove the wire harness. 4. Depress the four tabs that hold the light assembly on, one at a time, and pull the black bulb carrier away from the lamp.
Page 111 Lights Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly.
Page 112: Driver Controls
Driver Controls Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the INT1 speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed.
Page 113 Driver Controls Changing the wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm. 2. To remove, press the retaining clip (A) to disengage the wiper blade, then pull the blade down toward the windshield to remove it...
Page 114 Driver Controls TILT STEERING Push the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to the desired position. While holding the steering wheel, pull the lever up to its original position to lock the steering column.
Page 115 Driver Controls Forward storage bin and conversation mirror (if equipped) The storage compartment may be used to store two pairs of sunglasses or similar objects. Press the release control to open the storage compartment. The door will open slightly and can be moved to full open.
Page 116 Driver Controls Do not let children play with the moon roof. They may seriously hurt themselves. Power quarter rear windows • Without a moon roof • With a moon roof Press the portion of the VENT control to open the power rear quarter windows.
Page 117 Driver Controls Power liftgate control (if equipped) Without a moon roof With a moon roof Press and release the top portion of the control to open the power liftgate. Press and release the top portion of the control again to close the power liftgate.
Page 118 Driver Controls AUXILIARY POWER POINT Power points are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power points can cause damage not covered by your warranty. An auxiliary power point is located by the passenger’s ankle near the floor in the front console bin.
Page 119: Power Windows
Driver Controls A third auxiliary power point is located on the right rear quarter panel. The power point is accessible from the liftgate. POWER WINDOWS When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Page 120 Driver Controls The following views are the driver’s side switches: Normal operation • Push down (to the first detent) and hold the top portion of the switch to open. • Pull up (to the first detent) and hold the top portion of the switch to close.
Page 121 Driver Controls One touch up or down (if equipped) This feature is present on the driver’s window only. To operate ONE TOUCH DOWN: • Press the switch completely down to the second detent and release quickly. The driver’s window will open fully.
Page 122: Mirrors
Driver Controls Security Override If during a bounce-back condition, the switch is released to the neutral position, then held in the one touch up position within two seconds after the window reaches the bounce-back position, the window will travel up with no bounce-back protection. If the switch is released before the window reaches fully closed or the ignition is turned OFF (without accessory delay being active), the window will stop.
Page 123 Driver Controls Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up.
Page 124 Driver Controls Reverse tilt down mirrors The side mirrors tilt down when the vehicle is put in R (Reverse). Refer to the Message Center in the Driver Controls chapter to turn this feature ON or OFF. Signal indicator mirrors When the turn signal is activated, the lower portion of the mirror housing will blink.
Page 125 Driver Controls POWER ADJUSTABLE FOOT PEDALS The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. •...
Page 126: Speed Control
Driver Controls • When this feature is disabled, the running boards will immediately move to the stowed position regardless of the position of the doors. • When this feature is enabled, the running boards will immediately move to the correct position based on the position of the doors. Bounce-back: •...
Page 127 Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release 2. Accelerate to the desired speed. 3. Press the SET + control and release it.
Page 128 Driver Controls Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 48 km/h (30 mph). Increasing speed while using speed control There are two ways to set a higher speed:...
Page 129 Driver Controls • Depress the brake pedal or press CNCL (Cancel) until the desired vehicle speed is reached, press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or press CNCL (Cancel).
Page 130 Driver Controls In AM, FM1, or FM2 mode: • Press MEM to select preset stations within the selected radio band. In Tape mode: • Press MEM to select the next selection on the tape. In CD mode: • Press MEM to select the next selection on the CD.
Page 131 Driver Controls Press FAN + or - to adjust fan speed. Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press to select: •...
Page 132 Driver Controls Navigation control features Press and hold VOICE briefly until the voice icon appears on the Navigation display to use the Navigation voice command. Press RPT (REPEAT) control to hear previous command repeated from the navigation system. Climate control features Press TEMP + or - to adjust temperature.
Page 133 Driver Controls When programming your HomeLink Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S.
Page 134 Driver Controls 3. Simultaneously press and hold both the HomeLink and hand-held transmitter button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming”...
Page 135 Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink to accept the signal from the hand-held transmitter. After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling”...
Page 136: Message Center
Driver Controls Erasing HomeLink buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Page 137 Driver Controls Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy •...
Page 138 Driver Controls degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2.
Page 139 Driver Controls 8. Press the RESET control to start the compass calibration function. 9. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWLY TO CALIBRATE display changes to CALIBRATION COMPLETED. It will take up to five circles to complete calibration.
Page 140 Driver Controls Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3.
Page 141 Driver Controls • Power Deployable Running Boards (if equipped) • Language Autolocks This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode.
Page 142 Driver Controls 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select a new Autolamp delay value. Reverse Sensing System This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected.
Page 143 Driver Controls “RUNNING BOARDS MANUAL” will be displayed when the power function is disabled. 3. Select this function from the SETUP control for the current display mode. 4. Press the RESET control to manually set the power running boards in the OUT (deployed) position with the doors closed. When IN is selected the running boards resume to the automatic mode.
Page 144 Driver Controls System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds.
Page 145 Driver Controls This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Status Check park assist Warning displays when R (reverse) gear is selected. PRNDL error no park assist AdvTrac ON Displays for 4 seconds AdvTrac OFF Power liftgate off Door ajar...
Page 146 Driver Controls ADVTRAC ON. Displayed when the AdvanceTrac is ON. ADVTRAC OFF. Displayed when the AdvanceTrac is OFF. POWER LIFTGATE OFF. Displayed when the Power liftgate is turned OFF. DOOR AJAR. Displayed when a door is not completely closed. LIFTGATE AJAR. Displayed when the liftgate or liftgate glass is not completely closed.
Page 147 Driver Controls CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible.
Page 148 Driver Controls DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Charging system • Door sensor • Washer fluid • Brake fluid • Compass • Outside temperature • Engine sensor Contact your dealer as soon as possible if these messages occur on a regular basis.
Page 149 Driver Controls A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.
Page 150 Driver Controls Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is raised the liftgate could be damaged against a low ceiling. To open the liftgate from the Overhead console: Refer to Overhead controls in this section.
Page 151 Driver Controls Resetting the power liftgate: The power liftgate may not operate under these conditions. If any of these conditions occur, the power liftgate must be reset. • a low voltage or dead battery • disconnected battery • the liftgate has been left open, or in the partially latched position, for more than six (6) hours.
Page 152 Driver Controls LUGGAGE RACK The rear cross-bar can be adjusted to fit the item being carried. The front cross-bar does not move. To adjust cross-bar position: 1. Loosen the thumbscrews at both ends of the rear cross-bar. 2. Slide the cross-bar to the desired location.
Page 153: Locks And Security
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency.
Page 154 Locks and Security Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 155 Locks and Security • 4–button remote • 5–button remote Press the control a second time within three seconds to unlock all doors and liftgate. Locking the doors/liftgate Press this control to lock all doors and liftgate. To confirm all doors are closed and locked, press the control a second time within three seconds and the horn will chirp.
Page 156 Locks and Security • 5–button remote If any of the doors or liftgate are ajar, the horn will make two quick chirps, reminding you to properly close all doors. Unlocking the liftgate window Press the control to unlatch the liftgate window. •...
Page 157 Locks and Security Opening the power liftgate (if equipped) Press the control twice to fully unlatch and open the liftgate. Make sure all persons are clear of the liftgate area before using power liftgate control. In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an obstacle, Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate.
Page 158 Locks and Security • 4–button remote • 5–button remote To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the control will automatically move the seat, rearview mirrors, and adjustable pedals to the desired memory position (the memory position corresponds to the transmitter being used).
Page 159 Locks and Security • 5–button remote Activating the memory feature To activate this feature: 1. Position the seat, rearview mirror, and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to which you would like to associate with Driver 1 or Driver 2 positions.
Page 160 Locks and Security Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. The typical operating range for your remote entry transmitter is approximately 10 meters (33 feet). A decrease in the operating range could be caused by: •...
Page 161 Locks and Security Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: •...
Page 162 Locks and Security Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Unlock all doors using the power door lock/unlock control.
Page 163 Locks and Security • the engine is running and • you shift into any gear putting the vehicle in motion. Relock The autolock feature repeats when: • any door (except the drivers) is opened then closed while the engine is running, and •...
Page 164 Locks and Security • on the owner’s wallet card in the glove compartment, • at your dealer, • or on the module located under the right-hand side of the instrument panel, adjacent to the passenger compartment fuse panel. Note: The 5–digit code (e.g. 12345) will be in large, BOLD numbers on the module label.
Page 165 Locks and Security Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code.
Page 166 Locks and Security SECURILOCK PASSIVE ANTI-THEFT SYSTEM SecuriLock passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems.
Page 167 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Lincoln coded key. If your keys are lost or stolen you will need to do the following: •...
Page 168 Locks and Security 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least three seconds, but no more than ten seconds). 2.
Page 169: Seating And Safety Restraints
Seating and Safety Restraints Seating and Safety Restraints SEATING Front row adjustable head restraints Your vehicle’s seats are equipped with four-way adjustable head restraints. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 170 Seating and Safety Restraints Adjusting the front power seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 171 Seating and Safety Restraints Press the control to recline the seatback forward or rearward. Memory seats/rearview mirrors/adjustable pedals This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the driver door.
Page 172 Seating and Safety Restraints • Push the icon on the button to activate cooled seats. A blue light illuminates on the button. Push the icon again to disengage. • Push the icon on the button to activate heated seats. A red light illuminates on the button.
Page 173 Seating and Safety Restraints • There is a filter located under both front seats. • It can be accessed from the second row seat. Move the front seat all the way forward and up to ease access. To remove climate controlled seat air filter: •...
Page 174 Seating and Safety Restraints • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 175 Seating and Safety Restraints Adjusting the 2nd row outboard seat for E-Z Entry The 2nd row outboard seats allow for easier entry and exit to and from the 3rd row seat. To enter the 3rd row seat: 1. Locate the handle on the side of the seat, lifting it to release the seatback.
Page 176 Seating and Safety Restraints 3. To return the seat to a seating position, push down on the seat until the seat is latched to the floor. 4. With the seat in the flat back position, lift up on the lever located on the side of the seat cushion.
Page 177 Seating and Safety Restraints 1. Locate the handle on the side of the seat, lifting it to release the seatback. 2. Ensure that the seat back is locked in the down position by applying pressure to the seat back. 3. Locate the latch strap at the front of the seat and pull to release the seat into a kneel down load floor position.
Page 178 Seating and Safety Restraints The rear latch hooks must be properly engaged with the floor striker. Position the rear legs of the seat over the floor strikers and engage. 2. With the seat in the flat back position, lift up on the lever located on the side of the seat cushion.
Page 179 Seating and Safety Restraints 2. With the latch released the seatback can be lowered into the load floor position. 3. To return the seat to the upright position, lift the seatback until the latch is fully engaged. Adjusting the second row 20% seat (if equipped) Lift the handle to move the seat forward or backward.
Page 180 Seating and Safety Restraints Reclining the second row 40% seatback Locate the release handle located on the outboard side of the seat cushion and lift gently to allow the seatback to be adjusted to the desired location. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Page 181 Seating and Safety Restraints The head restraints can be moved up and down. Push control to lower head restraint. Folding down the third row seat to the load floor To prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position.
Page 182 Seating and Safety Restraints Pull up on the handle located behind the seatback while pushing the seatback forward and down into the seat cushion. To return the seatback to its original position lift the seatback until it latches into place. Third row power folding seat (if equipped) The control buttons are located on the right-hand rear quarter trim panel (accessible from the liftgate area).
Page 183: Safety Restraints
Seating and Safety Restraints Push the top of the control button to return the seatback to its original position. The power folding seats are designed to stall within 1–10 seconds of encountering an obstruction when opening or closing. Should this occur, remove the obstruction and wait approximately 1–4 minutes for the seat motor to reset.
Page 184 Seating and Safety Restraints • Restraint system warning light and back-up tone. • The electrical wiring for the air bags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, and indicator lights. How does the personal safety system work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions.
Page 185 Seating and Safety Restraints Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System to tailor the air bag deployment and safety belt pretensioner activation depending upon safety belt usage.
Page 186 Seating and Safety Restraints If any of these things happen, even intermittently, have the Personal Safety System serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 187 Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
Page 188 Seating and Safety Restraints movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
Page 189 Seating and Safety Restraints How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return to the vehicle sensitive (emergency) locking mode. After any vehicle collision, the combination lap and shoulder belt system at all passenger seating positions must be checked by a qualified technician to verify that the “automatic locking retractor”...
Page 190 Seating and Safety Restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, right front passenger and second row outboard passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 191 Seating and Safety Restraints Conditions of operation If... Then... The driver safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds.
Page 192 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36 700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers.
Page 193 Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 194 Seating and Safety Restraints 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. • After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.
Page 195: Air Bags
Seating and Safety Restraints safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Page 196 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection to an occupant in the center front seating position.
Page 197 Seating and Safety Restraints Children and air bags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Page 198 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 199 Seating and Safety Restraints impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 200 Do not attempt to service, repair, or modify the Safety Canopy system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 201 Seating and Safety Restraints • Two crash sensors mounted in the front doors (one on each side). • Two crash sensors located at the c-pillar behind the rear doors (one on each side). • Rollover sensor in the restraints control module (RCM). The Safety Canopy system, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact...
Page 202 Seating and Safety Restraints Several Safety Canopy system components get hot after inflation. Do not touch them after inflation. If the Safety Canopy system has deployed, the Safety Canopy will not function again unless replaced. The Safety Canopy system (including the A, B and C pillar trim) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
Page 203: Child Restraints
Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by law to use safety restraints for children in the U.S.
Page 204 Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury.
Page 205 Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top...
Page 206 Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child.
Page 207 Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Air bag supplemental restraint system (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).
Page 208 Seating and Safety Restraints Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 209 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 210 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 211 Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Page 212 Seating and Safety Restraints • outboard seating positions • center seating position (if equipped) 3. Route the child safety seat tether strap under the head restraint (outboard seats) and over the back of the seat. 4. Grasp the tether strap and position it to the seat frame.
Page 213 Seating and Safety Restraints 5. Rotate the tether strap, and clip the tether strap to the anchor on the seat frame. 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Third row seating position 1.
Page 214 Seating and Safety Restraints • You may need to pull back the top of the hinged panel along the bottom of the seat back to access the tether anchor. 4. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly...
Page 215 Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol: Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Page 216 Seating and Safety Restraints Attach LATCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it.
Page 217: Driving
Driving Driving STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
Page 218 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 219 Driving 5. Turn the key to 3 (ON) without turning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Page 220 Driving fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. Using the engine block heater (if equipped) If your vehicle is factory-equipped with an engine block heater, a rubber cap/plug assembly will be...
Page 221: Brakes
Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least 2.5 cm (one inch) or adjust the heating or air conditioning to bring in fresh air.
Page 222 Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. Using ABS • In an emergency or when maximum efficiency from the four-wheel ABS is required, apply continuous force on the brake.
Page 223 Driving Parking brake with auto-release (if equipped) Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 224 Driving If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy.
Page 225: Air Suspension
Driving AIR SUSPENSION SYSTEM The air suspension system is designed to improve ride comfort, vehicle handling and general vehicle performance by adjusting the vehicle’s ride height according to vehicle speed, weight added to or removed from the vehicle and four-wheel drive (if equipped) operation. Normal vehicle operation does not require any action by the driver.
Page 226 Driving On vehicles equipped with air suspension, turn the air suspension and the ignition switch off prior to jacking, hoisting or towing your vehicle. To remove the second panel, press the tab down to unlock the access panel. 2004 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus) I n f o r ma t i o n P r o v i d e d b y :...
Page 227 Driving Press the bottom portion of the switch to turn off the air suspension. LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited slip axle functions like a standard rear axle.
Page 228 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 229 Driving Roll Stability Control enhances your vehicle’s stability during maneuvers that require all available tire traction, like in wet/snowy/icy road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall vehicle traction, and have better control of the vehicle. The Roll Stability Control system helps the driver maintain steering control if the vehicle begins to slide excessively left or right or spin out.
Page 230 Driving The Roll Stability Control button allows the driver to control the availability of the Roll Stability Control system. The Roll Stability Control system status is indicated by a warning indicator light with a “sliding car” icon in the instrument cluster that will flash when the system is activated and an indicator light in the control button that will illuminate when the system is turned off.
Page 231: Transmission Operation
Driving Do not alter or modify your vehicle’s suspension or steering; the resulting changes to the vehicle’s handling can adversely affect the Roll Stability Control system. Also, do not install a stereo loudspeaker near the front center console or under either front seat.
Page 232 Driving 2. Using a smooth, non-metallic tool (such as a plastic screwdriver, or equivalent) between the shift lever boot and the plastic bezel, pry the bezel assembly away from its locking tabs. Use caution not to damage the plastic bezel assembly or shift lever boot when prying the bezel assembly from the locking tabs.
Page 233 Driving 4. Press and hold the white button located along side the shifter housing assembly (as shown in the illustration). Press the gearshift lever release on the shifter knob and move the gearshift lever back to N (Neutral) (two places rearward from P [Park]).
Page 234 Driving be slightly delayed. Once the engine coolant temperature reaches 71° C (160° F) the normal shift strategy will resume. This is normal operation and will not affect the function or the durability of the transmission. If the normal shift strategy does not resume once the engine coolant temperature reaches the normal operating temperature, or if the downshifts and other throttle conditions do not function normally, see your dealer or a qualified service technician as soon...
Page 235 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 236 Driving (Overdrive) can be deactivated by pressing the transmission control switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate in the instrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch (TCS) on the end of the gearshift lever with the gearshift in the position.
Page 237 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Page 238 Driving throttle conditions do not function normally, see your dealer or a qualified service technician as soon as possible. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting from forward and reverse gears, stopping between shifts in a steady pattern.
Page 239 Driving The system is not effective at speeds greater than 10 km/h (6 mph) and may not detect certain angular or moving objects. The system detects obstacles up to a maximum range of six meters (20 ft.) behind the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone...
Page 240 Driving CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW) is selected while the vehicle is moving, the system will not engage.
Page 241 Driving Positions of the Control Trac system The Control Trac system functions in four modes: • 2H (2WD HIGH) delivers power to the rear wheels only. This is appropriate for normal on-road driving on dry pavement. • A4WD (4X4 AUTO) provides electronic control four-wheel drive with power delivered to all four wheels, as required, for...
Page 242 Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
Page 243 Driving Shifting from 2H, A4WD or 4H to 4L 1. Bring the vehicle to a stop and keep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4L position. Note: Some noise may be heard as the system shifts or engages. Shifting from 4L to 4H, A4WD or 2H 1.
Page 244 Driving The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside.
Page 245 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 246 Driving called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surface to return the vehicle to a safe direction of travel. •...
Page 247 Driving momentary clunk and ratcheting sounds. This is the front drivetrain coming up to speed and engaging the front wheels, and is not cause for concern. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail.
Page 248 Driving slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water, their fluids should be checked and changed, if necessary.
Page 249 Driving Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control. Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating.
Page 250 Changing the Tires in the Roadside emergencies chapter). If you have questions regarding tire replacement, see an authorized Ford or Lincoln/Mercury dealer. If you nevertheless decide to equip your four–wheel drive for off-road use with tires larger than what Ford Motor Company recommends, you should not use these tires for highway driving.
Page 251 Driving Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare).
Page 252: Vehicle Loading
Driving If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Page 253 Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. •...
Page 254: Trailer Towing
Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
Page 255 The kit containing a electrical jumper and trailer tow electrical instructions may be purchased from any Ford, Lincoln, or Mercury dealership (Part number 4L1Z-14A348-AA) Note: Before towing a trailer, make sure the trailer brakes (if equipped) and lamps are properly connected and functional.
Page 256 Driving Trailer weight Rear axle Maximum GCWR - range (0 - Engine ratio kg (lbs.) maximum) kg (lbs.) 5.4L with standard 5397 (11900) 0–2721 (0–6000) trailer tow package 5.4L with optional 6576 (14500) 0–3900 (0–8600) trailer tow package 5.4L with standard 5533 (12200) 0–2721 (0–6000)
Page 257 Driving Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control, vehicle rollover and personal injury. INTEGRATED HITCH RATING The standard integrated hitch has two ratings depending on mode of operation: •...
Page 258 Driving Trailer hitch cover Your vehicle is equipped with a removable trailer hitch trim cover. To remove the trim cover: 1. Loosen the two push pins in the bottom of the cover by turning them counterclockwise with a flathead screwdriver or similar object. 2.
Page 259 Driving (Overdrive) for 10 seconds, then return the gearshift lever to P (Park) and release the brake. With the ignition still in the ON position, and all doors closed, allow the vehicle to stand (without passengers) for several minutes so that it can level. 2.
Page 260 Driving Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. •...
Page 261 Driving When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper. • do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper.
Page 262: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Owner Information Guide in the glove compartment.
Page 263: Fuel Pump Shut-Off Switch
If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Page 264 Roadside Emergencies The fuel pump shut-off switch is located in the left rear quarter trim panel, near the liftgate. The switch is located behind two access panels; the second panel has a tab that needs to be pushed down to remove the access panel door.
Page 265: Fuses And Relays
Roadside Emergencies The fuel pump shut-off switch has a red reset button on top of it and is located beneath the air suspension switch (if equipped). If the vehicle is not equipped with air suspension, the fuel pump shut-off switch’s red reset button will still be visible behind this access panel.
Page 266 Roadside Emergencies Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Cartridge Fuse Mini...
Page 267 Roadside Emergencies To remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. To reinstall it, line up the tabs with the grooves on the panel, then push it shut.
Page 268 Roadside Emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 10A* Run/Accessory - Instrument cluster, Front wiper motor, Rear wiper motor, Tire Pressure Monitor System (TPMS) module 20A* Brake On/Off (stoplamp) switch, Turn signal/Hazard flasher, AdvanceTrac stoplamps relay, Stoplamps, Center High-Mounted Stoplamp (CHMSL), Turn...
Page 269 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 7.5A* Brake On/Off (stoplamp) switch, Powertrain Control Module (PCM) (keep alive power), EATC control head, Body Security Module (BSM) (keep alive power), Speed control deactivation switch, Speed control servo, SecuriLock LED, 3rd row seat relay coils, Power liftgate module, Clock, Brake Shift Interlock (BSI) solenoid...
Page 270 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 10A* Rear window defroster relay coil, A/C refrigerant containment switch, A/C compressor thermistor, DEATC control head, DEATC solenoids, DEATC blower controller, Trailer tow battery charge relay coil 10A* Daytime Running Lamps (DRL) ignition relay coil, Digital Transmission Range Sensor (DTRS back-up lamps), Trailer tow back-up...
Page 271 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 10A* Moonroof switch illumination, Flip window switch, Flip window relays, Flip window motors, Electronic Hidden Antenna Module (EHAM) antenna amplifier (navigation radio), Radio (delayed accessory feed), Left front window motor, Navigation radio amplifier 10A* RH low beam...
Page 272 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 20A* HEGO sensors, EGR vacuum regulator (EVR) solenoid, Intake Manifold Tuning valve (IMTV) solenoid, Canister vent solenoid, Vapor Management valve (VMV) solenoid, A/C compressor clutch relay coil 20A* PCM, Idle Air Control (IAC) solenoid, Mass Air Flow (MAF) sensor, Fuel injectors, Fuel pump relay, Fuel pump shut-off switch, Fuel...
Page 273 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 30A** Auxiliary A/C blower relay, Auxiliary A/C blower motor 30A** Passenger seat motor switch, Passenger seat lumbar switch and motor 30A** Driver seat lumbar switch and motor, Memory module, Power memory mirrors, Adjustable pedals switch and motor 30A** Power running boards...
Page 274 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Rear window Fuse 8 (heated mirrors), Rear window defrost relay defroster, Heated outside mirrors, Rear window defroster indicator (climate control head) Trailer tow Trailer tow 7–wire connector (battery battery charge) charge relay...
Page 275 Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires.
Page 276 Roadside Emergencies Removing the jack and tools 1. Open the liftgate, then locate the access panel on the floor behind the 3rd row seat. Unlatch and remove the panel. 2. Remove the jack and tools assembly tray from the compartment by turning the wing-nut counterclockwise to relieve tension against the jack assembly tray.
Page 277 Roadside Emergencies On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet (located in the rear floor compartment behind the 3rd row seat with the jack tray tools assembly kit) for detailed tire change instructions.
Page 278 Roadside Emergencies 3. Obtain the spare tire and jack from their storage locations. Turn off the air suspension switch (the air suspension switch is located behind two trim panels on the left rear quarter trim panel. Refer to Air Suspension System in the Driving section for more information.).
Page 279 Roadside Emergencies When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). To prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite wheel is blocked.
Page 280 Roadside Emergencies • Never use the front or rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Page 281 Roadside Emergencies 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center. After doing so, pull on the cable to align the components at the end of the cable. 3. Assemble the jack handle and winch extension (as shown in illustration), then insert the winch extension through the access hole...
Page 282: Jump Starting
Roadside Emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Page 283 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 284 Roadside Emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 2004 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus) I n f o r ma t i o n P r o v i d e d b y :...
Page 285 Roadside Emergencies 4. Make the final connection of the negative (-) cable to the jump starting stud located in the rear of the engine compartment, near the battery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 286 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 287 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 288: Wrecker Towing
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 289 Roadside Emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. With a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle can be towed (all wheels on the ground) under the following conditions: Special Conditions: •...
Page 290: Customer Assistance
Customer Assistance Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
Page 291 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 292 • Protection against covered repair costs after your Bumper-to-Bumper Warranty expires. You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs.
Page 293 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
Page 294 Customer Assistance from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form.
Page 295 Customer Assistance Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board.
Page 296 Customer Assistance In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final; the arbitrator’s award is binding both to you and Ford of Canada.
Page 297 Customer Assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com.
Page 298: Reporting Safety Defects (U.s. Only)
Customer Assistance 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company...
Page 299: Cleaning
Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 300 Cleaning • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained body-side cladding, roof racks, bumper step surfaces, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.
Page 301 Cleaning • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Page 302 Cleaning • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth.
Page 303 Cleaning CLEANING THE CLIMATE CONTROLLED SEATS (IF EQUIPPED) Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Clean the seat with a damp cloth, using a mild soap and water solution, if necessary. LEATHER SEATS Your leather seating surfaces have a clear, protective coating over the leather.
Page 304 Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 305: Maintenance And Specifications
Maintenance and Specifications Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 306 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the front of the hood, just above the passenger side headlamp.
Page 307: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V V8 engine 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8.
Page 308: Engine Oil
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter.
Page 309 Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable.
Page 310 Maintenance and Specifications Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening.
Page 311: Battery
Maintenance and Specifications that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery...
Page 312 Maintenance and Specifications Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 313 Maintenance and Specifications 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 314 Maintenance and Specifications • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range”...
Page 315 Maintenance and Specifications Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container.
Page 316 Maintenance and Specifications To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1.
Page 317 Maintenance and Specifications Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 318 Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The and the symbol will illuminate. • The “Service Engine Soon” indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 319 Maintenance and Specifications 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Page 320 Maintenance and Specifications • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. •...
Page 321 Maintenance and Specifications Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops.
Page 322 Maintenance and Specifications Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty. Octane recommendations Your vehicle is designed to use “Premium”...
Page 323 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. •...
Page 324 Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Page 325 Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 326 Maintenance and Specifications • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving.
Page 327 Maintenance and Specifications • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system.
Page 328 Maintenance and Specifications detected a malfunction. Temporary malfunctions may cause your Check Engine/Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3.
Page 329 Maintenance and Specifications 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times.
Page 330 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
Page 331 Maintenance and Specifications You can check the fluid without driving if the ambient temperature is above 10°C (50°F). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C COLD...
Page 332: Air Filter(S)
Maintenance and Specifications DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance guide for maintenance intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element.
Page 333 Maintenance and Specifications 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated.
Page 334 Maintenance and Specifications government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Page 335 Maintenance and Specifications • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacturer. • Inflation pressure: A measure of the amount of air in a tire. •...
Page 336 Maintenance and Specifications Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different than this example.) 1.
Page 337 Maintenance and Specifications Letter rating Speed rating - km/h (mph) 159 km/h (99 mph) 171 km/h (106 mph) 180 km/h (112 mph) 190 km/h (118 mph) 200 km/h (124 mph) 210 km/h (130 mph) 240 km/h (149 mph) 270 km/h (168 mph) 299 km/h (186 mph) Note: For tires with a maximum speed capability over 240 km/h (149 mph), tire manufacturers sometimes use the letters ZR.
Page 338 Maintenance and Specifications 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 ⁄...
Page 339 Maintenance and Specifications Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information than those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks.
Page 340 Maintenance and Specifications Information on “T” type tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different than this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light...
Page 341 Maintenance and Specifications Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns. Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or blowout , with unexpected loss of vehicle control and increased risk of injury.
Page 342 Maintenance and Specifications 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts, bulges or other irregularities.
Page 343 Maintenance and Specifications • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) 2004 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus) I n f o r ma t i o n P r o v i d e d b y :...
Page 344 Maintenance and Specifications • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a reputable repair facility to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 345 Maintenance and Specifications the tread is worn down to 4mm (1/16th of an inch). When you see these “wear bars”, the tire is worn out and should be replaced. Inspect your tires frequently for any of the following conditions and replace them if one or more of the following conditions exist: •...
Page 346 Maintenance and Specifications closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving or you suspect your tire or vehicle has been damaged, immediately reduce your speed.
Page 347: Changing Tires
Maintenance and Specifications is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair of fix as necessary. If all tires appear to be inflated, carefully drive the vehicle to the nearest location where air can be added to the tires.
Page 348: Part Numbers
Maintenance and Specifications SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Page 349: Refill Capacities
Maintenance and Specifications Component 5.4L 4V V8 engine Spark plugs* AGSF-32PM * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft High Fill to line on Performance reservoir DOT 3 Motor...
Page 350 Maintenance and Specifications Fluid Ford Part Application Capacity Name Front axle Motorcraft SAE 4 x 4 vehicles 1.8-2.0L (3.5-3.7 lubricant 75W-90 Fuel pints) Efficient High Performance Synthetic Rear Axle Lubricant Rear axle Motorcraft SAE Conventional 2.13L (4.5 pints) lubricant 75W-90 Fuel differential Efficient High (9.75 inch axle)
Page 351: Lubricant Specifications
Maintenance and Specifications an automatic transmission application requiring MERCON may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage. Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.
Page 352 Maintenance and Specifications Ford part Ford part Ford Item name number specification Brake fluid Motorcraft High PM-1 ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Driveshaft, slip Premium Long XG-1-C or ESA-M1C75–B spline, double Life Grease XG-1-K Cardan joint center ball Engine coolant...
Page 353 Maintenance and Specifications Ford part Ford part Ford Item name number specification Rear axle Motorcraft SAE XY-75W90–QFEHP meets API GL-5 75W-90 Fuel Efficient High Performance Synthetic Rear Axle Lube Motorcraft SAE XY-75W140–QL WSL-M2C192-A 75W-140 High Performance Synthetic Rear Axle Lube Front axle Motorcraft SAE XY-75W90–QFEHP meets API GL-5...
Page 354 Maintenance and Specifications MERCON and MERCON V type fluids are not interchangeable. DO NOT mix MERCON and MERCON V. Use of a transmission fluid that indicates dual usage (MERCON and MERCON V) in an automatic transmission application requiring MERCON may cause transmission damage.
Page 355 Maintenance and Specifications 2004 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus) I n f o r ma t i o n P r o v i d e d b y :...
Page 356 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 357 Maintenance and Specifications Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certification label which is located on the door pillar. The following table tells you which transmission or transaxle each code represents. Truck application: Code Transmission Description Manual transmission Manual 5–speed overdrive (Mazda R2) Manual 5–speed overdrive (Close ratio)
Page 358 Maintenance and Specifications Code Transmission Description Automatic 5–speed overdrive (5R55S) Passenger car application: Code Transmission/Transaxle Description Front wheel drive manual transaxle 5–speed overdrive (MTX75) 5–speed overdrive (M5) Front wheel drive automatic transaxle 4–speed overdrive (4FE) 3–speed (Mazda) 4–speed overdrive (AX4S) 4–speed overdrive (4F20E) 4–speed overdrive (4F50N) 4–speed overdrive (CD4E)
Page 359: Accessories
Not all accessories are available for all models. Following is a list of several Lincoln Genuine Accessory products. Not all accessories are available for all models. To find out what accessories are available for your vehicle, please contact your dealer or visit our online store at: www.lincolnaccessories.com.
Page 360: Rear Seat Entertainment System
Accessories Lifestyle Bike racks Cargo organization and management Engine block heaters and blankets Rear seat entertainment systems Trailer hitches, wiring harnesses and accessories Peace of mind Airbag anti-theft locks First aid and safety kits Full vehicle covers Locking gas cap Remote start Vehicle security systems For maximum vehicle performance, keep the following information in...
Page 361: Index
Index Index acid, treating emergencies ..311 jumping a disabled battery ..282 maintenance-free ....311 ABS (see Brakes) .....221 replacement, specifications ...348 Accessory delay ......122 servicing ........311 Air bag supplemental restraint BeltMinder .........191 system ........195, 199 and child safety seats ....197 Brakes ........221 description ......195, 199 anti-lock ......221–222 disposal ........202...
Page 362 Index safety belts ......302 washing ........299 Daytime running lamps waxing ........299 (see Lamps) ......100 wheels ........300 wiper blades ......301 Defrost rear window ......98 Clock ..........117 Dipstick Compass, electronic automatic transmission set zone adjustment ....138 fluid ..........330 Console ........148 engine oil .........308 overhead ......114–116 Doors rear ..........149...
Page 363 Index change oil soon warning, quality ........322 message center .......308 running out of fuel ....322 checking and adding ....308 safety information relating to dipstick ........308 automotive fuels .....319 filter, specifications ..310, 348 Fuses ........265–266 recommendations ....310 refill capacities ......349 specifications ....351, 354 Exhaust fumes ......220 Garage Door Opener (see Homelink wireless control...
Page 364 Index HomeLink universal bulb replacement specifications chart ....103 transceiver (see Garage door daytime running light .....100 opener) ........136 fog lamps ........99 Homelink wireless control headlamps .........99 headlamps, flash to pass ..100 system ........132 instrument panel, dimming ...101 Hood ..........306 interior lamps ....103–104 replacing bulbs ....103, 105–108, 110 Lane change indicator...
Page 365 Index side view mirrors (power) ..124 Preparing to drive your vehicle ........227 Motorcraft parts ....323, 348 Radio ........16, 21 Navigation system .......43 Rear window defroster ....98 cd functions ......59 Relays ........265 destination mode ......71 DVD location ......92 Remote entry system ..154, 157 map mode .........62 illuminated entry ....162 quick start .........45...
Page 366 Index climate control ......171 recreational towing ....261 memory seat ....158, 171 trailer towing ......254 wrecker ........288 SecuriLock passive anti-theft system ....166–167 Transmission ......231 Servicing your vehicle ....305 brake-shift interlock (BSI) ..231 Snowplowing .........7 fluid, checking and adding (automatic) ......330 Spare tire (see Changing the Tire) ...........275 fluid, refill capacities ....349 lubricant...
Page 367 I n f o r ma t i o n P r o v i d e d b y :...
Page 368 I n f o r ma t i o n P r o v i d e d b y :...

This manual is also suitable for:

Navigator 2003

Lincoln Navigator 2004 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Quick Links

Table of Contents

Related Manuals for Lincoln Navigator 2004

Summary of Contents for Lincoln Navigator 2004

This manual is also suitable for:

Table of Contents