Table of Contents
Advertisement
Quick Links
Introduction
ZiLOG's Ethernet Smart Cable (ESC), ZENETSC0100ZACG, allows you to connect the
®
Z8 Encore!
, Z8 Encore! XP
ZiLOG Developer Studio II (ZDS II) host-system using an Ethernet connection.
This user manual provides instructions for installing ESC hardware. Instructions are also
provided for Ethernet-equipped host PCs that are not network-connected. Once the ESC is
connected, proceed with debugging as described in the development kit documentation.
Kit Contents
For details on kit contents, refer to Ethernet Smart Cable Packing List (PAK0019).
Software and Hardware Requirements
The software and hardware requirements are described below:
•
A host PC with ZDS II v4.10.0 or later for Z8 Encore!, eZ80Acclaim!, or ZNEO. For
ZDS II host system requirements, refer to the development kit Quick Start Guide. You
can download the latest version of ZDS II from www.zilog.com.
Note:
If you are using ZDS II—eZ80Acclaim! versions earlier than 4.10.0, see
Using ESC on ZDS II—eZ80Acclaim! Versions Earlier than 4.10.0
on page 12.
•
An available 10/100 Mbps Ethernet connection.
Supported Target Environments
The supported target environments are described in the table below.
Development Board
Z8 Encore!
ZNEO
Copyright © 2007 by ZiLOG, Inc. All rights reserved.
Ethernet Smart Cable
User Manual
®
™
, ZNEO
, or eZ80Acclaim!
System Clock
Minimum Maximum
32 kHz
20 MHz
10 kHz
20 MHz
www.zilog.com
UM020702-0107
®
development board to a
Power Supply
Minimum Maximum
2.7 V
3.6 V
2.7 V
3.6 V
Current*
2 mA
2 mA
Advertisement
Table of Contents
Related Manuals for ZiLOG ZENETSC0100ZACG
Summary of Contents for ZiLOG ZENETSC0100ZACG
-
Page 1: Kit Contents
Ethernet Smart Cable User Manual UM020702-0107 Introduction ZiLOG’s Ethernet Smart Cable (ESC), ZENETSC0100ZACG, allows you to connect the ® ® ® ™ Z8 Encore! , Z8 Encore! XP , ZNEO , or eZ80Acclaim! development board to a ZiLOG Developer Studio II (ZDS II) host-system using an Ethernet connection. -
Page 2: Installing The Ethernet Smart Cable
Ethernet Smart Cable User Manual Page 2 System Clock Power Supply Current* Development Board Minimum Maximum Minimum Maximum eZ80Acclaim! 5 MHz 50 MHz 3.0 V 3.6 V 2 mA *Add this current for ESC requirement on your target's power supply. Installing the Ethernet Smart Cable The ESC is optimized for use on an Ethernet network in which a Dynamic Host Configuration Protocol (DHCP) server assigns IP addresses. - Page 3 Ethernet Smart Cable User Manual Page 3 The green PWR and RUN LEDs illuminate. The green link LED on the ESC RJ-45 cable illuminates (see Figure 1), indicating a live Ethernet connection. The green activity LED on the ESC RJ-45 connector flickers, indicating network activity. DBG Connector Ethernet Connector RUN LED...
- Page 4 Ethernet Smart Cable User Manual Page 4 9. Click the OK button in the Project Settings window. Your project is now configured to run with the newly installed ESC. Now connect the target board to the ESC as described in Connecting to the Target Board on page 11.
- Page 5 Ethernet Smart Cable User Manual Page 5 Figure 2. The Network Dialog UM020702-0107 Installing the Ethernet Smart Cable...
- Page 6 Ethernet Smart Cable User Manual Page 6 5. In the panel labeled LAN or High-Speed Internet, double-click the Local Area Connection icon. The Local Area Connection Status dialog box appears, as displayed in Figure Figure 3. The Local Area Connection Status Dialog Installing the Ethernet Smart Cable UM020702-0107...
- Page 7 Ethernet Smart Cable User Manual Page 7 6. In the Local Area Connection Status dialog box, click the Properties button. The Local Area Connection Properties dialog box appears, as displayed in Figure Figure 4. The Local Area Connection Properties Dialog 7.
- Page 8 Ethernet Smart Cable User Manual Page 8 Figure 5. The Internet Protocol Properties Dialog 8. Enter an IP address of and a subnet mask of . These 192.168.1.21 255.255.255.0 values place the PC on the same network as the ESC, and do not conflict with the IP address of the ESC.
- Page 9 Ethernet Smart Cable User Manual Page 9 Follow the steps below to change the ESC default settings: 1. Obtain the ESC IP address. 2. Open your web browser to the IP address located in step 1. The ESC home web page appears (see Figure The Settings tab provides access to ESC network settings.
- Page 10 Ethernet Smart Cable User Manual Page 10 Figure 7. Ethernet Smart Cable Password Web Page 3. Once the configuration in the Settings tab are changed, click the Submit button. A message acknowledging that changes have been made appears beneath the web page. 4.
-
Page 11: Connecting To The Target Board
ESC to your target board, refer to either eZ80Acclaim! Design for Debug Technical Note (TN0035) or Z8 Encore! Design for Debug Technical Note (TN0036). Troubleshooting Tips If a hardware failure is suspected, contact a local ZiLOG representative for assistance. Before submitting a problem report to ZiLOG Customer Support, follow the instructions below:... - Page 12 Follow the procedure below to obtain the IP address of the ESC when configured for DHCP: 1. Download the ESC Scan utility installation file from http://www.zilog.com/software/ zds2.asp under the miscellaneous section. 2. Run the installation file to install it to your local drive.
-
Page 13: Customer Support
For answers to technical questions about the product, documentation, or any other issues with ZiLOG’s offerings, please visit ZiLOG’s Knowledge Base at http://www.zilog.com/kb. For any comments, detail technical questions, or reporting problems, please visit ZiLOG’s Technical Support at http://support.zilog.com. UM020702-0107... - Page 14 ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized.
Need help?
Do you have a question about the ZENETSC0100ZACG and is the answer not in the manual?
Questions and answers