Related Manuals for ZiLOG UM018112-0908
Summary of Contents for ZiLOG UM018112-0908
-
Page 1: Usb Smart Cable
USB Smart Cable User Manual UM018112-0908 ® Copyright ©2008 by Zilog , Inc. All rights reserved. www.zilog.com... -
Page 2: Revision History
USB Smart Cable Firmware Compatibility. Updated Installing the USB Smart Cable and Driver December Added ZLF645, Windows Vista- 2007 32, and USB Smart Cable firmware compatibility information. Put contents into the latest template. Changed ZiLOG to Zilog UM018112-0908 Revision History... -
Page 3: Table Of Contents
Customer Support........8 UM018112-0908... -
Page 4: Usb Smart Cable
, Z8 Encore! XP , ZNEO , or eZ80Acclaim! development board to a high-speed or full-speed USB port on Zilog Developer Studio II (ZDS II) host system. This user manual provides instructions for installing USB Smart Cable hardware and the associated drivers. When the USB Smart Cable is con- nected and the driver installed, you can proceed with debugging as described in the development kit documentation. - Page 5 Table 2. USB Smart Cable Firmware Compatibility CPU Family Firmware ® ® ® ® Z8 Encore! , Z8 Encore! XP , ZNEO , eZ80Acclaim! ZLF645 ® ® ® ® Z8 Encore! , Z8 Encore! XP , ZNEO , eZ80Acclaim! ZLF645 UM018112-0908 USB Smart Cable...
-
Page 6: Installing The Usb Smart Cable And Driver
CD-ROM provided. The installation procedure depends on your Windows operating system version. Note: Zilog no longer includes CD-ROMs with USB Smart Cable kits built August 2006 or later. Windows Vista-32/64 1. Connect the USB Smart Cable to the host PC. The Found New Hardware dialog box is displayed. -
Page 7: Windows Xp
1. Connect the USB Smart Cable to the host PC for the first time. The Found New Hardware Wizard should activate automatically. 2. In the Wizard, click Next. 3. Select Search for a suitable driver for my device (Recommended); then click Next. UM018112-0908 USB Smart Cable... -
Page 8: Windows 98 Se
4. Select Specify a location. Browse one of the following to the driver directory: <ZDS II Installation Directory> \device drivers\USB\x32 <ZDS II Installation CD>\Device Drivers\USB\x32 5. Click Next, and then click Next again after the appropriate driver is found. 6. Click Finish to complete the installation. UM018112-0908 USB Smart Cable... -
Page 9: Connecting To The Target Board
For further information on connecting the USB Smart Cable to your target board, refer to either eZ80Acclaim! Design for Debug Technical Note ® (TN0035) or Z8 Encore! Design for Debug Technical Note (TN0036). Figure 1. Connecting the Six-Conductor Ribbon Cable to the USB Smart Cable UM018112-0908 USB Smart Cable... -
Page 10: Troubleshooting Tips
USB Smart Cable User Manual Troubleshooting Tips If a hardware failure is suspected, contact a local Zilog representative for assistance. Before submitting a problem report to Zilog Customer Sup- port, follow the instructions in this section. USB Smart Cable Not Recognized Disconnect all other USB devices (including keyboard and mouse if you can use PS2 ports instead). -
Page 11: Customer Support
User Manual Customer Support For answers to technical questions about the product, documentation, or any other issues with Zilog’s offerings, visit Zilog’s Knowledge Base at http://www.zilog.com/kb. For any comments, detail technical questions, or reporting problems, visit Zilog’s Technical Support at http://support.zilog.com. - Page 12 Document Disclaimer ©2008 by Zilog, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT.
Need help?
Do you have a question about the UM018112-0908 and is the answer not in the manual?
Questions and answers