Toshiba Qosmio F40 Maintenance Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Qosmio F40
  6. Maintenance manual
Toshiba Qosmio F40 Maintenance Manual

Toshiba Qosmio F40 Maintenance Manual

Hide thumbs Also See for Qosmio F40:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Toshiba Personal Computer
Qosmio F40/F45
(PQF43x)
(PQF44x)
(PQF46x)
(PQF47x)
Maintenance Manual
TOSHIBA CORPORATION
S/ No
Qosmio F40/F45 Maintenance Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Qosmio F40

Summary of Contents for Toshiba Qosmio F40

  • Page 1 Toshiba Personal Computer Qosmio F40/F45 (PQF43x) (PQF44x) (PQF46x) (PQF47x) Maintenance Manual TOSHIBA CORPORATION S/ No Qosmio F40/F45 Maintenance Manual...
  • Page 2 The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Qosmio F40/F45 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.
  • Page 3 Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Qosmio F40/F45, referred to as Qosmio F40/F45 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
  • Page 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Qosmio F40/F45 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
  • Page 5 Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the XXXXX that appears on its display is presented in the type face below: Format complete System transferred Qosmio F40/F45 Maintenance Manual...
  • Page 6 Chapter 1 Hardware Overview...
  • Page 7 1 Hardware Overview 1.1 Features Qosmio F40/F45 Maintenance Manual...

  • Page 8: Table Of Contents

    DVD Super Multi (+-R Double Layer)............... 23 HD DVD-ROM......................25 HD DVD-R ......................... 26 Power Supply ......................27 Batteries ........................28 1.1.1 Main Battery..................28 1.1.2 Battery Charging Control ..............28 1.1.3 RTC Battery ..................29 Qosmio F40/F45 Maintenance Manual...
  • Page 9 Table 1-2 DVD Super Multi Drive Specifications ............23 Table 1-3 HD DVD-ROM Drive Specifications ............. 25 Table 1-4 HD DVD-R Drive Specifications..............26 Table 1-5 Battery Specifications ..................28 Table 1-6 Quick/Normal Charging Time ................ 29 Qosmio F40/F45 Maintenance Manual...

  • Page 10: Features

    1 Hardware Overview Features The Toshiba Qosmio F40/F45 a full size notebook PC based on the Core2 Duo Processor and Celeron M Processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time.
  • Page 11 The LCD displays available come with one of following two types: 15.4” WXGA CSV 1-Lamp 200nits color display, resolution 1280×800 15.4” WXGA CSV 2-Lamps 500nits color display, resolution 1280×800 Keyboard The keyboard supports 30 kinds of country keyboards. Qosmio F40/F45 Maintenance Manual...
  • Page 12 A PC Card slot is provided to hold PC Card Standard Type II (5.0 mm) card, capable of using a variety of PC Cards including 16-bit Multiple Function PC Cards and 32- bit Card Bus Cards. PC card HDD boot does not be supported. Qosmio F40/F45 Maintenance Manual...
  • Page 13 This slot is for your memory card requirements to provide memory card read on your computer. Toshiba Pointing Device Toshiba Pointing Device has one kind of Synaptic Touchpad. Sound System The Realtek ALC888 integrated audio controller supports multimedia. The sound...
  • Page 14 It also accelerates application loading and run time through intelligent file caching. The computer has 512 MB or 1 GB sizes of Robson card modules. Qosmio F40/F45 Maintenance Manual...

  • Page 15: Figure 1-1A Id Parts Description Placement Part A

    1 Hardware Overview 1.1 Features Figures 1-1A/1-1B/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively. Figure 1-1A ID Parts Description Placement Part A Qosmio F40/F45 Maintenance Manual...
  • Page 16 1.1 Features 1 Hardware Overview Figure 1-2B ID Parts Description Placement Part B Qosmio F40/F45 Maintenance Manual...
  • Page 17 1 Hardware Overview 1.1 Features Figure 1-3 Computer Block Diagram Qosmio F40/F45 Maintenance Manual...
  • Page 18 1.1 Features 1 Hardware Overview Figure 1-4 System Board Configurations Qosmio F40/F45 Maintenance Manual...

  • Page 19: System Unit Components

    1 Hardware Overview System Unit Components System Unit Components Figure 1-4 is Block Diagram of the System Unit Qosmio F40/F45 Maintenance Manual...
  • Page 20 1.2 System Unit Components 1 Hardware Overview Figure 1-5 System Unit Block Diagram Qosmio F40/F45 Maintenance Manual...
  • Page 21 − 12.71Kb used for ACPI − 30.03Kb used for CPU update module − 64.03Kb used for Intel VGA BIOS − 55.28Kb used for Finger Printer ROM − 51.44Kb used for string data − 39.13Kb used for nVidia G84 Qosmio F40/F45 Maintenance Manual...
  • Page 22 − Intel Matrix Storage Technology − PCI Interface − IDE Interface − Low Pin Count (LPC) Interface − Serial Peripheral Interface (SPI) − Compatibility Modules − Advanced Programmable Interrupt Controller (APIC) − Universal Serial Bus (USB) Controller Qosmio F40/F45 Maintenance Manual...
  • Page 23 2 stereo ADCs support 16/20/24-bit PCM format. All DACs support 44.1 k/48 k/96 k/192 kHz sample rate. All ADCs support 44.1 k/48 k/96 k sample rate. Qosmio F40/F45 Maintenance Manual...
  • Page 24 − I2C communication control Battery EEPROM 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack. − Storing records of battery use Clock Generator SLG8SP510 − Generating the clock signal required for the system Qosmio F40/F45 Maintenance Manual...
  • Page 25 − IEEE 802.11ag − IEEE 802.11agn Data Rate − IEEE 802.11g: Standard 54M bps − IEEE 802.11ag: Standard 54M bps − IEEE 802.11agn: Standard 130M bps Frequency Channel − IEEE802.11a: 2.4GHz − IEEE802.11ag: 2.4GHz / 5.4GHz Qosmio F40/F45 Maintenance Manual...
  • Page 26 1.2 System Unit Components 1 Hardware Overview − IEEE802.11agn: 2.4GHz / 5.4GHz Qosmio F40/F45 Maintenance Manual...

  • Page 27: Inch Hdd

    300 GB Rotational Speed 4200 rpm 5400 rpm 4200 rpm 4200 rpm 4200 rpm (RPM) Height 12.5 mm 9.5 mm 9.5 mm 12.5 mm 12.5 mm User Data Sectors 312,581,808 390,721,968 488,397,168 586,072,368 Bytes / Sector Qosmio F40/F45 Maintenance Manual...

  • Page 28: Dvd Super Multi (+-R Double Layer)

    Access Time (ms) Average Random Access Data Buffer Size (Mbytes) DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+R, DVD+-R (Double Layer), DVD+RW. Formats Supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (Multi- Session), Video CD, CD-Extra (CD+), CD-Text. Qosmio F40/F45 Maintenance Manual...
  • Page 29 1 Hardware Overview HD DVD-ROM Qosmio F40/F45 Maintenance Manual...

  • Page 30: Hd Dvd-Rom

    DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+-R, DVD+-R (Double Layer), DVD+RW, HD DVD-ROM Formats Supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROM XA, Photo CD (Multi- Session), HS CD-RW,US CD-RW, Video CD, CD-Extra (CD+), CD-Text, CD-MIDI, CD-I, CD-I Bridge. Qosmio F40/F45 Maintenance Manual...

  • Page 31: Hd Dvd-R

    DVD+-R, DVD+-R (Double Layer), DVD+RW, HD DVD-ROM, HD DVD-R, HD DVD-R (Double Layer). Formats Supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROM XA, Photo CD (Multi- Session), HS CD-RW,US CD-RW, Video CD, CD-Extra (CD+), CD-Text, CD-MIDI, CD-I, CD-I Bridge. Qosmio F40/F45 Maintenance Manual...

  • Page 32: Power Supply

    Monitors the voltage output to the system block (load/logic circuit side). Monitors the voltage, over voltage, input/output current of the battery pack. Monitors the internal temperature of the battery pack. Monitors the supply voltage from the AC adapter. Qosmio F40/F45 Maintenance Manual...

  • Page 33: Batteries

    8769L controls the charge on/off state and detects a full charge. Battery Charge When the AC adapter is attached, the battery is charged by off-state charge when the system is powered off or by on-state charge when it is powered on. Qosmio F40/F45 Maintenance Manual...

  • Page 34: Rtc Battery

    The current in the battery charging circuit drops below the predetermined value. The charging time exceeds the fixed limit. 1.1.3 RTC Battery The RTC battery provides power to keep the current date, time and other system information in memory while the computer is turned off. Qosmio F40/F45 Maintenance Manual...
  • Page 35 2 Troubleshooting 概要 Chapter 2 Troubleshooting Qosmio F40/F45 Maintenance Manual...

  • Page 36: System Board Configurations

    Procedure 1 ODD Cleaning Check ............... 2-18 Procedure 2 Test Program Check ..............2-18 Procedure 3 Connector Check and Replacement Check....... 2-18 LAN........................2-20 Procedure 1 Test Program Check ..............2-20 Procedure 2 Connector Check and Replacement Check....... 2-20 2-ii Qosmio F40/F45 Maintenance Manual...
  • Page 37 IEEE 1394 Test ....................2-24 Procedure 1 Test Program Check ..............2-24 Procedure 2 Connector Check ..............2-24 2.14 Cooling Module....................2-25 Procedure 1 Test Program Check ..............2-25 Procedure 2 Connector Check and Replacement Check....... 2-25 Qosmio F40/F45 Maintenance Manual 2-iii...

  • Page 38: Figure

    2 Troubleshooting Figures Figure 2-1 Basic flowchart(1/2)..................2-3 Tables Table 2-1 HDD error code and status................2-13 2-iv Qosmio F40/F45 Maintenance Manual...

  • Page 39: Outline

    2. Phillips screwdrivers (2 mm, 2.5 mm) 3. Cleaning disk kit (for ODD drive cleaning) 4. Bootable CD 5. Multi-meter 6. External monitor 7. Headphone 8. Microphone 9. A-BEX TEST DVD 10. Music CD 11. DVD TSD-1 (TOSHIBA EMI DVD Test Media) Qosmio F40/F45 Maintenance Manual...

  • Page 40: Basic Flowchart

    Make sure the Windows® Vista Home Premium has been installed on the HDD. Any other operating system can cause the computer to malfunction. Make sure any piece of optional equipment has been installed. Qosmio F40/F45 Maintenance Manual...
  • Page 41 Message "In Touch with Tomorrow Toshiba" displayed procedure in Section 2.7 See the previous page to "Password=" displayed ?? delete the password. Follow the HDD diagnostic OS started ?? procedure in Section 2.5 Figure 2-1 Basic Flowchart (1/2) Qosmio F40/F45 Maintenance Manual...
  • Page 42 Perform the continuous test to check if the error is intermittent. Identify the test resulting in the Any error detected by the error and perform the appropriate diagnostic program ?? diagnostic procedures The system is normal. Figure 2-1 Basic Flowchart (2/2) Qosmio F40/F45 Maintenance Manual...
  • Page 43 10. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting procedures in section 2.13. 11. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.14. Qosmio F40/F45 Maintenance Manual...

  • Page 44: Power Supply

    Battery LED Battery LED Power supply status On in Amber Battery being charged On in Blue Battery fully charged, with AC adapter connected Blinking in Amber Battery low *1 while driving the computer (at equal intervals) Else Qosmio F40/F45 Maintenance Manual...
  • Page 45 Make sure the DC IN LED goes on in Blue. If it does not, go to Procedure 2. Check 2 Make sure the Battery LED goes on in Amber or Blue. If it does not, go to Procedure 3. Qosmio F40/F45 Maintenance Manual...

  • Page 46: System Board

    Check 2. Check 2 Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3. Check 3 Replace the CPU with a new one. Qosmio F40/F45 Maintenance Manual...

  • Page 47: Procedure 1 Message Check

    The error message appears when either data stored in RAM to be resumed is lost because the battery has been exhausted or the system board is faulty. If any other error message displays, perform Check 3. Check 3 Resume failure and press any key to continue. Qosmio F40/F45 Maintenance Manual...

  • Page 48: Procedure 2 Test Program Check

    Procedure 3 Replacement Check The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one. 2-10 Qosmio F40/F45 Maintenance Manual...

  • Page 49: Hdd

    Type FDISK and press the Enter key. Choose “Display partition Check 2 information” from the FDISK menu. If drive C is listed, perform Check 3. If drive C is not listed, return to the FDISK menu and choose the option to Qosmio F40/F45 Maintenance Manual 2-11...
  • Page 50 Enter FORMAT C:/S/U to format the HDD and transfer system files. If the following message appears on the display, the HDD has been formatted. Format complete If you cannot format the HDD using the test program, go to Procedure 4. 2-12 Qosmio F40/F45 Maintenance Manual...
  • Page 51 Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed Disk dos not support SMART Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error Qosmio F40/F45 Maintenance Manual 2-13...
  • Page 52 The System board may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 4. Check 4 The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. 2-14 Qosmio F40/F45 Maintenance Manual...

  • Page 53: Keyboard

    Chapter 4. If the problem persists, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Qosmio F40/F45 Maintenance Manual 2-15...

  • Page 54: Display

    Procedure 3. If there is still an error, perform Check 2. Check 2 The LCD/FL cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 3. 2-16 Qosmio F40/F45 Maintenance Manual...
  • Page 55 The CPU may be faulty. Replace it with a new one following the instructions in Chapter 4. Check 10 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 10. Qosmio F40/F45 Maintenance Manual 2-17...

  • Page 56: Odd (Optical Disk Drive)

    CD in the computer's CD, turn on the computer and run the test. Then insert a test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3 for information on how to perform the test.
  • Page 57 Chapter 4. If the problem persist, perform Check 6. Check 6 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. Qosmio F40/F45 Maintenance Manual 2-19...

  • Page 58: Lan

    Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-20 Qosmio F40/F45 Maintenance Manual...

  • Page 59: Sd/Sd-Io/Ms/Ms Pro/Mmc/Xd Card

    Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Qosmio F40/F45 Maintenance Manual 2-21...

  • Page 60: Finger Print (Optional)

    If the Finger Print is still not functioning properly, perform Check Check 2 The system board may be defective. Replace the system board with a new one following the steps described in Chapter 4. Then go through procedure 1 again. 2-22 Qosmio F40/F45 Maintenance Manual...

  • Page 61: Audio Test

    Chapter 4. If the problem persist, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Qosmio F40/F45 Maintenance Manual 2-23...

  • Page 62: Ieee 1394 Test

    Chapter 4. If the problem persists, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-24 Qosmio F40/F45 Maintenance Manual...

  • Page 63: Cooling Module

    Chapter 4. If the problem persists, perform Check 4. Check 4 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Qosmio F40/F45 Maintenance Manual 2-25...
  • Page 64 Chapter 3 Diagnostic Programs...
  • Page 65 Save Batch Parameters ................21 3.3.6 LOG Parameters Setting................ 22 3.3.7 Specify LOG Viewer................23 3.3.8 Display LOG File .................. 23 3.3.9 LOG Viewer ..................24 3.3.10 LOG File Sample................... 25 Subtests ........................27 System Test......................... 30 QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 66 3 Diagnostic Programs Memory Test....................... 34 Storage ........................40 Video........................... 44 Communication (COMM) ..................53 3.10 Peripheral ........................54 3.11 Error Codes and description..................58 3.12 Quick Test Item List ....................63 QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 68: General

    Video Test Communication Test Peripheral Test Keyboard Layout Test Hot Key Test Audio Play Test Audio Record Test DMI Read DMI Write Finger Printer Detect Test Finger Printer Scan Test Finger Printer Information Clear System Information QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 69 A Service Diagnostic BOOT CD A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) A CD-ROM Driver (for CD-ROM test)

  • Page 70: Quick Start

    Please see the following example-- Mouse test. Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the menu, then press Space key to select it. (When it is being selected, there is a X marked in the QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 71 Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally. The test result will be displayed in the following screen: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 72 CPU Speed Test (Step by Step): Select test item: Select System—CPU—CPU Speed, then, press the Enter key. Parameters Setting Choose the OK button after you set the proper parameters in the following window. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 73 As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 74: Keyboard Layout Test

    It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it must press the ‘Enter’ key at the same time. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 75: Hotkey Test

    Pass; otherwise Fail. The test will repeat for four times. When the test is completed, a file named autest.log will be saved in the defined location. 3.2.7 DMI Read Read the information from the system’s SMBIOS and display it in the screen as follows: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 76: Dmi Write

    1 line before user’s editing. User can modify the line and press Enter to confirm the current edition and attribute’s value in the 2 continue editing the next attribute. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 77: Finger Printer Detect Test

    FAIL if it always fails. Note: Because, execution of this test vanishes all fingerprint data. When you perform this test, please make it only failure of a fingerprint sensor. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 78: Finger Printer Information Clear

    The name of the program is marked on the top of the screen. At the bottom, the function keys are listed for user operation. During the detection, keyboard operation is invalid. When the detection is finished, the hardware components information will be displayed as follows: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 79: View Logs

    Press ESC to exit this program. 3.2.13 View Logs User can enter one choice to view a log file in the screen as follows. 3.2.14 Exit to Free DOS Select this item to exit to Free DOS. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 80: The Diagnostics Screen Explanation

    Detailed error report could be viewed with Logview.exe. When pressing ESC key during the test process, a User Break Windows will be popped up for the user to select. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 81 Current Time(C. TIME): Current system time, e.g. ‘C.TIME:2006-07-05 09:21:27’ in the above screen; Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining test time at the same location as Current TIME (C. TIME) in the above screen; QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 82 Wait On Error: Display ‘WAIT’ as shown in the above screen when ‘Wait On Error’ is enabled; Pause Enable: Display ‘PAUSE’ when “Pause Enable” is enabled; Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually interrupt the test process. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 83: Options

    Execute all selected test items in this editor. The hot key is F8. If “Interactive” option in batch parameters has not been selected, a warning message would be shown as below: • Edit Batch Parameters QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 84: Batch Parameters Configuration

    • Exit to DOS Exit the Service Diagnostics Editor and back to DOS. 3.3.2 Batch Parameters Configuration The batch parameters configuration screen can be accessed through Service Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH PARAMETERS: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 85 When the option here is enabled, it would affect all the test items while the same option in “Item Parameters Configuration” only affect that test item. Monitor Battery Life Monitor the remaining battery capacity (percent). QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 86: Item's Parameters Configuration

    3.3.3 Item’s Parameters Configuration The test items’ parameters configuration screen can be accessed through Service Diagnostics/Options -> Edit Batch Parameters -> Item’s Parameters-> System- >CPU-> Basic Functionality: Repeat count • Repeat times of the test item. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 87: Load Batch Parameters

    3.3.4 Load Batch Parameters Batch parameter is saved in the script file whose extension name is INI (*.INI). Below is the screen shot of “Load Batch Parameters”. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 88: Save Batch Parameters

    In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 89: Log Parameters Setting

    Log Test End Time If selecting this parameter, the end time of the test will be recorded. Log Errors Only If selecting this parameter, errors will be recorded only when the test fails. Log Errors Only with Time QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 90: Specify Log Viewer

    You can specify the Log file viewer in the Specify Log Viewer screen. The default viewing program of Service Diagnostics is LogView.exe. 3.3.8 Display LOG File You can specify the Log file for viewing in the Display Error Log File screen. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 91: Log Viewer

    In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: ↑, ↓ • Scroll a line backward or forward on the screen. Page Up, Page Down • QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 92: Log File Sample

    The following section is a sample of log file: DIAG REPORT <Module Name>: Service Diagnostic Ver 1.00 ... Memory Tester Build Date 2006.01.10 [Walk High] Begin Time: Wed Jul 05 10:45:36 2006 QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 93 [MSTPad] Begin Time: Wed Jul 05 10:48:54 2006 Touch Pad Test : FAIL ITEM TEST FAIL Function ID :502 Error Code :50202 Error Message :Touch Pad Test Fail End Time: Wed Jul 05 10:49:16 2006 QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 94: Subtests

    [XWRCycle] 02 Read Cycle Test [XRCycle] 05 Walking 1's Test [WalkHigh] 06 Walking 0's Test [WalkLow] 07 Memory Address [Address] 08 Refresh Test [Refresh] 09 Cache Memory [CacheOne] 10 Random Memory 01 Randomize Test [Random] QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 95 VESA 800x600x64K Mode [V800600_16] VESA 800x600x32K Mode [V800600_24] VESA 800x600x16K Mode [V800600_32] VESA 800x600x32bit Mode 1024X768 Video Modes VESA 1024x768x256 Mode [V1024768_15] VESA 1024x768x64K Mode [V1024768_16] VESA 1024x768x32K Mode [V1024768_24] VESA 1024x768x16K Mode [V1024768_32] VESA 1024x768x32bit Mode QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 96 03 Mac Address Detection [MAC Address] 02 1394 01 GUID Detection [1394 R/W Test] Peripheral 01 Keyboard 01 Keyboard Data Line [KBDataLn] 02 Keyboard Led [KBLED] 03 Keyboard Clock Line [KBClokLn] 02 Mouse 01 TouchPad [MSTpad] QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 97: System Test

    2. CPU Speed This test item is to detect the work frequency of the current CPU. User should change the parameters setting in the following window before the test: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 98 This test item is used for getting & showing CPU Information. It will be displayed as follows: 5. CPU Protected Mode Test This test item is to check whether CPU protected mode instruction works normally. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 99 Subtest 03 FAN Speed Test 1. CPU Fan Speed Test This test item is to check whether the CPU fan currently used works normally in the different speeds of stop, slow, middle and fast. Below is the QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 100 3.5 System Test 3 Diagnostic Programs parameter setting dialog window. Set the range of Speed that is to be tested, then choose the OK button to test it. It will be displayed as follows: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 101: Memory Test

    Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 102 Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 103 Extended Pattern In addition to the above pattern test of the memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 104 Subtest 05 Walking 1’s Test The test item is to ensure that there is no short circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’. Subtest 06 Walking 0’s Test QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 105 This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data. Subtest 11 Data Bus Test This test item is to check whether the data bus works normally. Subtest 12 Memory Speed Test QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 106 3.6 Memory Test 3 Diagnostic Programs This test item is to check the data-transferring rate for the cache memory and the system memory. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 107: Storage

    If user chooses Special Size, the test of IDE HDD will be taken according to the coverage range that user chooses or time. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 108 This test item involves the following parameters: IDE HDD Test Range—is same as the description of the upper item. LBA Start, LBA End-- specify start and finish byte in LBA(Large Block Address); Option-- Select sequential test or random test; QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 109 SMART stands for Self-Monitoring, Analysis and Reporting Technology. SMART test will compare the attribute values with the threshold value in the HDD’s controller to confirm whether there is any failure in the HDD Subtest 02 ODD QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 110 RW under LBA mode with the location address increasing in sequence. 6. Tray Eject Test Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 111: Video

    It will be displayed as follows:. 2. Text Attribute This test item is to check whether the text attribute of normal, hi-intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 112 This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 113 8 colors). In the test, user is required to respond according to the instruction in the screen. 5. 80 * 25 Text Mode This test item is to check whether 80*25 Text Mode works normally. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 114 Subtest 02 640 * 480 VGA Mode This test item is to check whether 680*480 VGA Text mode works normally. In the test, user is required to respond according to the instruction in the screen. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 115 4. 1280X800 Video Modes Test Subtest 04 VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test item’s parameter dialog window: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 116 This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 06 LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 117 This test item is to check the video adapter’s composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instruction in the screen. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 118 3 Diagnostic Programs Subtest 10 DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond according to the instruction in the screen. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 119 3 Diagnostic Programs 3.10 Peripheral QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 120: Communication (Comm)

    Detect the vendor ID of the network card. 3. MAC Address Detection Detect the MAC address of the network card. Subtest 02 1394 GUID Detection This test item is used to read and display GUID from 1394 register. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 121: Peripheral

    1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Led Test Check whether the keyboard led works normally. If Power switch\Volume\Caps\Num\Scroll\AVButton\DC-In\Power\Battery turn on with blue,click YES to continue,else click No. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 122 3.10 Peripheral 3 Diagnostic Programs If Power\Battery\Bridge\Wireless turn on with Orange,click YES to continue,else click No. If Odd turn on with Orange,click YES to continue,else click No. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 123 Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point devices work normally. 1. Touch Pad Before test Touch Pad’s function, user should set a timeout time at below screen: QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 124 At the below screen of Touch Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 125: Error Codes And Description

    As above. problems. The test pattern read out from the Base Memory Error base memory is different from Test this memory chip on Address the one that has been written in multiple machines. this address. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 126 PCI Bus Scan Error PCI test fails. As above. PCI Device Access Error PCI access fails. As above. Check PCI configuration on main PCI Config Verification Wrong PCI configuration. board or PCI Device Error configuration. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 127 VESA Video Memory As above. As above. Test Error Check whether there is any Physical problems with the video VESA VRAM Test Error physical problem with the video card or the monitor. card or the monitor. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 128 Keyboard Map & Stroke Test Check the KBD connection and Test Fail fails. repeat the test. Clock Line Test Fail Clock Line Test fails. As above. Data Line Test Fail Data Line Test fails. As above. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 129 ROM for repair. CD Seek Error Either the disk or the CD-ROM Replace the disk or send the CD- is damaged. ROM for repair. Eject Error Wrong CD-ROM drive. Exit from the wrong drive. QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...

  • Page 130: Quick Test Item List

    VESA 1024x768x32bit Mode VESA Video Memory 10% or 3 minutes Color Purity Test Direct Color Test LCD Panel Sequential/Random Read 25% or 3 minutes SMART Check LAN Card Device ID Detection Vendor ID Detection Mac Address Detection QosmioF40/F45，dynabook Qosmio F40 Maintenance Manual...
  • Page 131 Chapter 4 Replacement Procedures...
  • Page 132 4 Replacement Procedures 4-ii Qosmio F40/F45 Maintenance Manual...
  • Page 133 Removing the ODD Bay Module (For Non-Tray Module) ....... 4-21 Installing the ODD Bay Module (For Non-Tray Module) ........ 4-22 Removing the ODD Bay Module (For Standard Module)......... 4-23 Installing the ODD Bay Module (For Standard Module) ........4-24 Qosmio F40/F45 Maintenance Manual 4-iii...
  • Page 134 Installing the VGA Cooling module and VGA Card (for VGA board Model) . 4-47 4.13 CPU Cooling Module and Fan................. 4-48 Removing the CPU Cooling module and Fan............ 4-48 Installing the CPU Cooling module and Fan ............. 4-49 4-iv Qosmio F40/F45 Maintenance Manual...
  • Page 135 Removing the FELICA card(for JAPANP Model Only) Bluetooth card and LED Board ....................4-68 Installing the FELICA card(for JAPANP Model Only) Bluetooth card and LED Board ....................4-69 4.23 Touch Pad and Button Board .................. 4-70 Removing the Touch Pad and Button Board ............ 4-70 Qosmio F40/F45 Maintenance Manual...
  • Page 136 RJ11 cable, TV Antenna Connector and B-CAS Card Slot ........4-75 Removing the RJ11 cable, TV Antenna Connector and B-CAS card slot ..4-75 Installing the RJ11 cable, TV Antenna Connector and B-CAS card slot ..4-76 4-vi Qosmio F40/F45 Maintenance Manual...

  • Page 137: Figure

    Figure 4-27 Removing the CPU ..................4-50 Figure 4-28 Installing the CPU ................... 4-51 Figure 4-29 Installing the CPU ................... 4-52 Figure 4-30 Removing the TV tunre..................4-53 Figure 4-31 Removing the broadcom card ................. 4-55 Qosmio F40/F45 Maintenance Manual 4-vii...
  • Page 138 Figure 4-39 Removing the touch pad and button board ............. 4-70 Figure 4-40 Removing speakers ..................4-72 Figure 4-41 Removing the switch board and volume board..........4-73 Figure 4-42 Removing the RJ11 cable, TV antenna connectoer and B-CAS card slot..4-75 4-viii Qosmio F40/F45 Maintenance Manual...

  • Page 139: General

    4.1 General 4 Replacement Procedures General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations.

  • Page 140: Safety Precautions

    DANGER: Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs.
  • Page 141 For AC input, be sure to use the AC adapter and AC power cable that come with your computer or Toshiba-recommended equivalents. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the computer and that all the cables and connectors are fastened securely.

  • Page 142: Before You Begin

    See the appropriate explanations and figures for screw sizes. To avoid personal injury, use care to handle components that have sharp edges or corners. After you have replaced a FRU, check that the FRU works correctly to ensure normal computer operation. Qosmio F40/F45 Maintenance Manual...

  • Page 143: Disassembly Procedures

    Check that all the required screws are used to secure the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure that the FRUs are secure. After installing a FRU, make sure that the FRU and computer work normally. Qosmio F40/F45 Maintenance Manual...

  • Page 144: Tools And Equipment

    M2 (2 mm) 0.22 N･m (2.2 kgf･cm) M2.5 (2.5 mm) 0.36 N･m (3.5 kgf･cm) M3 (3 mm) 0.51 N･m (5.0 kgf･cm) M2.5x4 PSP TITE screws 0.204 N･m (2.0 kgf･cm) M2.5x6 GIZA TITE screws 0.36 N･m (3.5 kgf･cm) Qosmio F40/F45 Maintenance Manual...

  • Page 145: Colors Of Screw Shanks

    U (stands for unique-pan head screws, studs, etc.) Symbol examples 6 mm bind screw 12 mm bind screw 5 mm stud (The numeral represents the rounded length of the threaded portion regardless of the entire stud length.) Qosmio F40/F45 Maintenance Manual...

  • Page 146: Removing The Battery Pack

    3. Slide the battery release latch and remove the battery pack from the computer. battery pack battery latch battery lock Figure 4-1 Removing the battery pack NOTE: Dispose of the used battery packs as required by local ordinances or regulations. Qosmio F40/F45 Maintenance Manual...

  • Page 147: Installing The Battery Pack

    NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth. 1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click. 2. Slide in the battery lock. Qosmio F40/F45 Maintenance Manual...
  • Page 148 2. When the eject button pops out slightly, push it again. 3. When the PC card pops out, grasp it and pull it out. PCI Express card Optional PC card Eject button Figure 4-2 Removing the PCI Express Card or PC card 4-10 Qosmio F40/F45 Maintenance Manual...
  • Page 149 2. After checking that the PC card is seated securely, push the PC card release lever slightly. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration. Qosmio F40/F45 Maintenance Manual 4-11...

  • Page 150: Memory Card

    2. Push the memory card to be removed until it stops then release the memory card. 3. When the memory card pops out, grasp it and pull it out. Memory card Figure 4-3 Removing the memory card 4-12 Qosmio F40/F45 Maintenance Manual...
  • Page 151 2. Checking that the memory card is seated securely. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration. Qosmio F40/F45 Maintenance Manual 4-13...

  • Page 152: Removing The Optional Memory

    Figure 4-4 Removing the optional memory 4. Spread out the two memory lock latches so that the memory module pops up. 5. Pull the memory module up and out at an angle, using care to avoid touching the connectors. 4-14 Qosmio F40/F45 Maintenance Manual...

  • Page 153: Installing The Optional Memory

    After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections. Qosmio F40/F45 Maintenance Manual 4-15...

  • Page 154: Smart Card

    1. Open the card cover. 2. Pull the B-CAS card to be removed, grasp it and pull it out. M2x4 flat head screw B CAS cover B CAS card Smart card Figure 4-5 Removing the B-CAS card 4-16 Qosmio F40/F45 Maintenance Manual...
  • Page 155 2. Checking that the B-CAS card is seated securely. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration. Qosmio F40/F45 Maintenance Manual 4-17...

  • Page 156: Hdd

    M2x4 flat head screw 2 HDD cover. 2. Remove the HDD and 2 HDD cover. M2x4 flat head screw Second HDD cover HDD pack HDD pack M2x5 flat head screw HDD cover Figure 4-6 Removing the HDD pack 4-18 Qosmio F40/F45 Maintenance Manual...
  • Page 157 5. Place the HDD pack on a flat surface (such as a desk), and remove the chassis. M3x4 black flat head screw HDD Chassis M3x4 black flat head screw Figure 4-7 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive. Qosmio F40/F45 Maintenance Manual 4-19...

  • Page 158: Installing The Hdd

    3. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides. 4. Insert the HDD pack. 5. Secure the HDD cover by tightening the HDD cover screw. 4-20 Qosmio F40/F45 Maintenance Manual...

  • Page 159: Odd Bay Module

    4. Push out on the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully it can become hot during operation. Push hear M2x4 flat head screw ODD bay module ODD bezel Figure 4-8 Removing the ODD bay module Qosmio F40/F45 Maintenance Manual 4-21...

  • Page 160: Installing The Odd Bay Module (For Non-Tray Module)

    1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Place the ODD bezel in the correct position. 4. Secure the ODD bay module with two M2x4 black flat head screw. 4-22 Qosmio F40/F45 Maintenance Manual...

  • Page 161: Removing The Odd Bay Module (For Standard Module)

    3. Push out on the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully it can become hot during operation. Push hear M2x4 flat head screw ODD bay module Figure 4-9 Removing the ODD bay module Qosmio F40/F45 Maintenance Manual 4-23...

  • Page 162: Installing The Odd Bay Module (For Standard Module)

    1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Secure the ODD bay module with two M2x4 black flat head screw. 4-24 Qosmio F40/F45 Maintenance Manual...
  • Page 163 4.3 ODD Bay Module 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1.
  • Page 164 Assemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1. Place the ODD bezel in the correct position and secure the following 4 latches. 2. Seat the bracket and secure it with four M2x3 black flat-head screws. 4-26 Qosmio F40/F45 Maintenance Manual...

  • Page 165: Speaker Cover And Keyboard

    1. Release the following 13 latches on the switch cover, in that order: - five bottom latches - two right and left latches - Six front latches 2. Remove the speaker cover. Speaker cover Latch Figure 4-12 Removing the speaker cover Qosmio F40/F45 Maintenance Manual 4-27...
  • Page 166 4.4 Speaker Cover and Keyboard M2 5x2 6 black bin screw Keyboard CN12 Figure 4-13 Removing the keyboard 3. Remove two M2.5x2.6 black bind securing screws. 4. Disconnect the keyboard cable from CN12 on the system board. 4-28 Qosmio F40/F45 Maintenance Manual...

  • Page 167: Installing The Speaker Cover And Keyboard

    2. Secure the keyboard with two M2.5x2.6 black bind screws. 3. Place the speaker cover in the correct position and secure the following 13 latches, in that order: - five bottom latches - two right and left latches - Six front latches Qosmio F40/F45 Maintenance Manual 4-29...

  • Page 168: Hotkey Board

    1. Disconnect the switch board flat cables from CN4 on the system board. 2. Remove two M2.5x3 white flat head screws. 3. Disconnect the switch board flat cables from CN5000 on the switch board. Hotkey board Hotkey board flat cable CN5000 Figure 4-14 Removing the hotkey board 4-30 Qosmio F40/F45 Maintenance Manual...
  • Page 169 1. Connect the hotkey board flat cables to CN5000 on the switch board. 2. Seat the switch board in the correct position. 3. Secure the switch board with two M2.5x3 white flat head screws. 4. Connect the switch board flat cables to CN4 on the system board. Qosmio F40/F45 Maintenance Manual 4-31...

  • Page 170: Mdc Module

    CAUTION: Do not touch the connectors on the MDC module or in the computer. Contaminated connectors can cause MDC module failures. M2x3 black bind screw MDC card CN17 MDCcable Figure 4-15 Removing the MDC module 4-32 Qosmio F40/F45 Maintenance Manual...

  • Page 171: Installing The Mdc Module

    Note: After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC module has been recognized by the system. If it has not been recognized yet, check the connections. Qosmio F40/F45 Maintenance Manual 4-33...

  • Page 172: Wireless Lan Card

    2. Remove the two M2x3 white bind screws securing the wireless LAN card. 3. Pull the wireless LAN card up and out at an angle. M2x3 white bin screw Gray Black White Antenna cable Wireless LAN card Figure 4-16 Removing the wireless LAN card 4-34 Qosmio F40/F45 Maintenance Manual...

  • Page 173: Installing The Wireless Lan Card

    CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4-35 Qosmio F40/F45 Maintenance Manual...

  • Page 174: Robson Card

    1. Remove the two M2x4 white bind screws securing the Robson card. 2. Pull the wireless Robson card up and out at an angle. M2x4 white bin screw Robson card Figure 4-17 Removing the Robson card 4-36 Qosmio F40/F45 Maintenance Manual...

  • Page 175: Installing The Robson Card

    2. Press down on the Robson card to secure it with two M2x4 white bind screws. CAUTION: Do not touch the connectors on the Robson card and in the computer with your bare hands. Robson card can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4-37 Qosmio F40/F45 Maintenance Manual...

  • Page 176: Display Assembly

    5. Remove four M2.5x5 white flat head screws securing the LCD module to the top cover. 6. Remove the wireless antenna cables, MIC cable and CCD cable from the top cover. 7. Remove the display module. 4-38 Qosmio F40/F45 Maintenance Manual...

  • Page 177: Figure

    3. Secure the display assembly with four M2.5x5 white flat head screws. 4. Close the display panel and turn the computer so the rear is facing you and secure two M2.5x8 black flat head screws. 4-39 Qosmio F40/F45 Maintenance Manual...

  • Page 178: Top Cover

    4. Disconnect the touch pad board flat cable from CN13. 5. Disconnect the Bluetooth cable from CN15. 6. Disconnect the FLICA flat cable from CN11. 7. Disconnect the LED board flat cable from CN1000. 8. . Disconnect the volume board flat cable from CN9. 4-40 Qosmio F40/F45 Maintenance Manual...
  • Page 179 12. Release the following 10 latches on the switch cover, in that order: - Three Left latches - Two right latches - Three front latches - two rear latches 13. Lift up the top cover. 4-41 Qosmio F40/F45 Maintenance Manual...

  • Page 180: Installing The Top Cover

    9. Connect the switch board flat cable from CN16 on the system board. 10. Connect the speaker cable from CN3 on the system board.. 11. Turn the computer upside down and secure it with the following 14 screws: - Eleven M2.5x8 black bind screws 4-42 Qosmio F40/F45 Maintenance Manual...

  • Page 181: System Board, Ac In Cable

    5. Remove one M2.5x8 black flat head screw on the system board. 6. Remove the system board. B CAS card module flat cable Audio board cable CN814 TV splitter cable CN16 PJ650 TV antenna TV antenna Figure 4-22 Removing the system board 4-43 Qosmio F40/F45 Maintenance Manual...
  • Page 182 4 Replacement Procedures 4.11 System Board, AC-IN cable...

  • Page 183: Installing The System Board, Ac In Cable

    5. Turn the computer upside down. 6. Connect the B-CAS card module flat cable to CN814, TV splitter cable to CN16 on the system board. 7. Connect the audio board cable to PJ650, TV antenna cable on the TV tuner. 4-45 Qosmio F40/F45 Maintenance Manual...
  • Page 184 4. Remove two M2x3 black flat head screws form VGA board. 5. Remove the VGA board. M2x5 black flat head screw VGA thermal module bracket VGA thermal module M2x3 black flat head screw VGA board Figure 4-24 Removing the VGA Cooling Module and VGA Board 4-46 Qosmio F40/F45 Maintenance Manual...
  • Page 185 1. Seat the VGA board. 2. Secure the VGA board with two M2x4 black flat head screws. 3. Secure the VGA board thermal module and VGA board bracket with one M2x4 black flat head screws. 4-47 Qosmio F40/F45 Maintenance Manual...

  • Page 186: Cpu Cooling Module And Fan

    7. Disconnect the fan cable form CN807and then remove the fan. M2x4 black flat head screw North bridge bracket CPU thermal module bracket CPU thermal module System board CN807 Figure 4-25 Removing the CPU cooling module and fan 4-48 Qosmio F40/F45 Maintenance Manual...

  • Page 187: Installing The Cpu Cooling Module And Fan

    4. Seat the CPU cooling module and bracket in the correct position and secure them with two M2x4 black flat head screws. 5. Seat the north bridge bracket in the correct position and secure them with two M2x4 black flat head screws. Qosmio F40/F45 Maintenance Manual 4-49...

  • Page 188: Cpu

    1. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a flat-blade screwdriver (in the order shown in the figure below). 2. Remove the CPU. Figure4-27 Removing the CPU 4-50 Qosmio F40/F45 Maintenance Manual...

  • Page 189: Installing The Cpu

    2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. Figure 4-28 Installing the CPU CAUTION: Seat the CPU by aligning the triangle with the shaded area. Qosmio F40/F45 Maintenance Manual 4-51...
  • Page 190 4.14 CPU 3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left. Figure 4-29 Securing the CPU 4-52 Qosmio F40/F45 Maintenance Manual...

  • Page 191: Tv Tuner

    1. Remove the two M2x2 black bind screws securing the TV Tuner card. 2. Pull the wireless TV Tuner up and out at an angle. M2x2 black flat head screw TV tuner Figure 4-30 Removing the TV Tuner Qosmio F40/F45 Maintenance Manual 4-53...

  • Page 192: Installing The Tv Tuner

    2. Press down on the TV Tuner to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the TV Tuner and in the computer with your bare hands. TV Tuner can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4-54 Qosmio F40/F45 Maintenance Manual...

  • Page 193: Broadcom Card

    1. Remove the two M2x2 black bind screws securing the Broadcom card. 2. Pull the wireless Broadcom card up and out at an angle. M2x3 black head screw Broadcom card Figure 4-31 Removing the Broadcom card Qosmio F40/F45 Maintenance Manual 4-55...

  • Page 194: Installing The Broadcom Card

    2. Press down on the Broadcom card to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands. Broadcom card can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4-56 Qosmio F40/F45 Maintenance Manual...
  • Page 195 TV tuner splitter card TV antenna S CN4000 Audio board Audio cable L ( ) CN4001 M2 5x4 white flat screw USB cable Audio cable S Figure 4-32 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Qosmio F40/F45 Maintenance Manual 4-57...
  • Page 196 3. Secure the TV tuner splitter card with two M2x3 black flat head screws. 4. Seat the USB cable in the correct position. 5. Secure the USB cable with two M2.5x4 white flat head screws. 6. Seat the sub-speaker in the correct position. 4-58 Qosmio F40/F45 Maintenance Manual...

  • Page 197: Display Mask

    - Five latches on each of the left and right sides - Eight top latches Seal M2 5x4 white flat head screw Display mask Seal M2 5x4 white flat head screw Latch Figure 4-33 Removing the display mask Qosmio F40/F45 Maintenance Manual 4-59...
  • Page 198 - Two M2.5x4.5 white flat head screws on bottom 3. Secure the following 4 seals to cover the screws, in that order: - Two black seals on the bottom - Two black seals on the top 4-60 Qosmio F40/F45 Maintenance Manual...

  • Page 199: Fl Inverter Board

    Figure 4-34 Removing the FL inverter board 2. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL connector. 3. Disconnect the HV cable from the HV connector and remove the FL inverter board. Qosmio F40/F45 Maintenance Manual 4-61...

  • Page 200: Installing The Fl Inverter Board

    1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector. 2. Seat the LCD module, FL inverter board in the correct position. 3. Secure the FL inverter board with one M2.5x4 black flat head screw. 4-62 Qosmio F40/F45 Maintenance Manual...

  • Page 201: Lcd Modules

    3. Remove three M2x3 white flat head screws on each side securing the LCD bracket. 4. Remove the LCD brackets. 5. Turn the LCD upside down. Be sure to place it on a cushioned surface such as a foam pad. Qosmio F40/F45 Maintenance Manual 4-63...
  • Page 202 Right LCD bracket Left LCD bracket Figure 4-35 Removing the 15.4-inch LCD module and screws 6. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-36 Removing the 15.4-inch LCD module 4-64 Qosmio F40/F45 Maintenance Manual...

  • Page 203: Installing The 15.4-Inch Lcd Module

    4. Place the LCD bracket in the correct position and secure it with three M2x3 black flat head screws on each side. 5. Please the LCD module in the correct position and secure it with two M2.5x4 white flat heat screws on each side. Qosmio F40/F45 Maintenance Manual 4-65...

  • Page 204: Ccd Board And Mic

    1. Disconnect the CCD cable from the CCD module connector and remove the CCD board. CCD board cable CCD board Figure 4-37 Removing the CCD board and MIC 2. Lift the MIC from the display rear cover. 4-66 Qosmio F40/F45 Maintenance Manual...

  • Page 205: Installing The Ccd Board And Mic

    Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-37. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the correct position. Qosmio F40/F45 Maintenance Manual 4-67...

  • Page 206: Flica Card(For Japanp Model Only), Bluetooth Card And Led Board

    Felica card bracket Felica card Bluetooth card Bluetooth card cable LED board flat cable CN6003 LED board M2x3 black flat head screw Figure 4-38 Removing the FLICA card, Bluetooth card and LED Board 4-68 Qosmio F40/F45 Maintenance Manual...

  • Page 207: Board

    M2x3 black flat head screws. 3. Connect the LED board flat cable to CN6003 on the LED board. 4. Seat the LED board in the correct position and secure it with the tow M2x3 black flat head screws. Qosmio F40/F45 Maintenance Manual 4-69...

  • Page 208: Removing The Touch Pad And Button Board

    M2x3 black flat head bind screw Mylar Touch pad bracket M2x3 black flat head screw Touch pad Button board flat cable Touch pad cable CN3000 CN3001 Button board Figure 4-39 Removing the touch pad and button board 4-70 Qosmio F40/F45 Maintenance Manual...

  • Page 209: Installing The Touch Pad And Button Board

    2. Seat the Mylar in the correct position. 3. Connect the button board flat cable to CN3001 on the button board. 4. Connect the touch pad flat cables to J1 on the touch pad and CN3000 on the button board. Qosmio F40/F45 Maintenance Manual 4-71...

  • Page 210: Speakers

    1. Seat the left and right speaker in the correct position. 2. Route the speaker cable in the wire guide. 3. Secure the left speaker with one M2x4 white flat head screw. 4. Secure the right speaker with two M2x4 white flat head screws. 4-72 Qosmio F40/F45 Maintenance Manual...

  • Page 211: Switch Board, Volume Board

    6. Disconnect the volume board flat cables from CN7000 on the volume board. M2x2 black flat head screw Volume board flat cable M2x3 black flat screw CN8000 Switch board flat cable Volume board CN7000 Switch board Figure 4-41Rmoving the Switch Board and Volume Board Qosmio F40/F45 Maintenance Manual 4-73...
  • Page 212 3. Secure the switch board with two M2x3 black flat head screws. 4. Connect the volume board flat cables to CN8000 on the volume board 5. Seat the volume board in the correct position. 6. Secure the volume board with two M2x2 black flat head screws. 4-74 Qosmio F40/F45 Maintenance Manual...

  • Page 213: Rj11 Cable, Tv Antenna Connector And B-Cas Card Slot

    5. Remove the B-CAS card slot. RJ11 cable M2x4 white flat M2x3 black flat head screw head screw TV antenna connector B CAS card slot Figure 4-42 Removing the RJ11 cable, TV Antenna Connector and B- CAS card Slot Qosmio F40/F45 Maintenance Manual 4-75...

  • Page 214: Installing The Rj11 Cable, Tv Antenna Connector And B-Cas Card Slot

    3. Seat the TV antenna connector in the correct position. 4. Secure the l TV antenna connector with one M2.5x4 white flat head screw. 5. Seat the RJ11cable in the correct position. 6. Route the RJ11cable in the wire guide. 4-76 Qosmio F40/F45 Maintenance Manual...
  • Page 215 次 6000 1 Appendices...

  • Page 216: Appendix A Handling The Lcd Module

    LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be carefully when handling it. Qosmio F40/F45 Maintenance Manual...
  • Page 217 Also, never scratch the surface. 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. Qosmio F40/F45 Maintenance Manual...
  • Page 218 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Qosmio F40/F45 Maintenance Manual...
  • Page 219 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. Qosmio F40/F45 Maintenance Manual...
  • Page 220 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. Qosmio F40/F45 Maintenance Manual...

  • Page 221: Appendix B Board Layout

    Apx. B Board Layout Appendices Appendix B Appendix B Board Layout System Board Front View Figure B-1 Board Layout (Front View) Qosmio F40/F45 Maintenance Manual...
  • Page 222 Appendices Apx. B Board Layout System Board Back View Figure B-2 Board Layout (Back View) Qosmio F40/F45 Maintenance Manual...
  • Page 223 PCMCIA Connector (68-Pin) .............. C-15 C.28 CN811 DDR2 DIMM1 Socket (200-Pin) ............C-16 C.29 CN812 SATA HDD-2 Connector (22-Pin) ............C-19 C.30 CN813 Mini Card Connector (52-Pin)............. C-19 C.31 CN814 BCAS Card Connector (10-Pin) ............C-20 Qosmio F40/F45 Maintenance Manual...
  • Page 224 JACK801 IR Blaster-1 Connector (6-Pin) ............C-29 C.48 JACK802 RJ45 LAN Connector (12-Pin) ............C-29 C.49 JACK4000 External Microphone Connector (6-Pin)..........C-30 C.50 JACK4001 Line In Connector (6-Pin) ..............C-30 C.51 JACK4002 Head Phone Connector (9-Pin) ............C-30 C.52 JACK4003 Video In Connector (6-Pin)..............C-31 Qosmio F40/F45 Maintenance Manual...

  • Page 225: Cn1 Lcm / Fl Inverter Connector (40-Pin

    N$813641 N$813641 N$813641 N$813641 N$813641 N$813641 INV_PWM_3 N$1181584 DGND DGND DGND DGND Speaker Sub-Woofer Connector (4-Pin) Table C-2 Speaker Sub-Woofer Connector Pin Assignments (4-Pin) Pin No. Signal Name Pin No. Signal Name SPK_SUB- SPK_SUB+ DGND DGND Qosmio F40/F45 Maintenance Manual...
  • Page 226 Table C-5 Camera Module Connector Pin Assignments (5-Pin) Pin No. Signal Name Pin No. Signal Name +V5S_CAMERA USB_P7- USB_P7+ DGND DGND Internal Microphone Connector (2-Pin) Table C-6 Internal Microphone Connector Pin Assignments (2-Pin) Pin No. Signal Name Pin No. Signal Name ANAGND MIC_IN Qosmio F40/F45 Maintenance Manual...

  • Page 227: Cn7 Robson Module Connector (52-Pin

    +V3S 5 in 1 Memory Card Reader Connector (44-Pin) Table C-8 5 in 1 Memory Card Reader Connector Pin Assignments (44-Pin) Pin No. Signal Name I/O Pin No. Signal Name DGND MS_BS_SD_CMD_SM_WEZ MS_DATA1_SD_DAT1_SM_D1 I/O MS_DATA0_SD_DAT0_SM_D0 I/O Qosmio F40/F45 Maintenance Manual...
  • Page 228 Pin No. Signal Name VOL_A DGND VOL_B DGND LED_DIMM#_BUFFER +VLED +VLED C.10 CN11 Felica Card Connector (6-Pin) Table C-10 Felica Card Connector Pin Assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name +V5S_FELICA USB_P9- USB_P9+ DGND Qosmio F40/F45 Maintenance Manual...
  • Page 229 USB Port8 M/B to IO/B Connector (16-Pin) Table C-12 USB Port8 M/B to IO/B Connector Pin Assignments (16-Pin) Pin No. Signal Name Pin No. Signal Name DGND USB_P8+ USB_P8- DGND IM_CLK_5 IM_DAT_5 DGND +V3S +V3S +V5S +V5S DGND DGND DGND Qosmio F40/F45 Maintenance Manual...

  • Page 230: Cn15 Blue Tooth Board Connector (10-Pin

    SCAN_IN(6) SCAN_IN(5) SCAN_IN(3) SCAN_IN(2) SCAN_IN(1) C.15 CN17 MODEM Board Connector (12-Pin) Table C-15 MODEM Board Connector Pin Assignments (12-Pin) Pin No. Signal Name Pin No. Signal Name DGND MC97_3S_SDOUT DGND MC97_3S_SYNC DGND N$737061 DGND MC97_3S_RST# MC97_3S_BITCLK Qosmio F40/F45 Maintenance Manual...

  • Page 231: Cn18 Wireless Lan Module Connector (52-Pin

    PCIE_C_TXN2 ICH_3A_ALERT_DAT PCIE_C_TXP2 DGND DGND DGND WLAN_LED# +V1.5S DGND +V3S C.17 CN19 Audio Board Connector (20-Pin) Table C-17 Audio Board Connector Pin Assignments (20-Pin) Pin No. Signal Name Pin No. Signal Name +V5S +V5S SPDIF DGND Qosmio F40/F45 Maintenance Manual...

  • Page 232: Cn20 Usb Port2 / Port3 Connector (8-Pin

    DGND SVID_L_LUMA SVID_L_CHROMA C.20 CN801 CRT Connector (15-Pin) Table C-20 CRT Connector Pin Assignments (15-Pin) Pin No. Signal Name Pin No. Signal Name N$1091421 N$1091416 N$1091413 DGND DGND DGND DGND N$838148 DGND N$1163226 HSYNC VSYNC C-10 Qosmio F40/F45 Maintenance Manual...

  • Page 233: Hdmi Connector (19-Pin

    DGND C.23 CN806 USB Port0 / Port1 Connector (8-Pin) Table C-23 USB Port0 / Port1 Connector Pin Assignments (8-Pin) Pin No. Signal Name Pin No. Signal Name USBVCC1 USB_L_P1- USB_L_P1+ DGND USBVCC1 USB_L_P0- USB_L_P0+ DGND Qosmio F40/F45 Maintenance Manual C-11...

  • Page 234: Cn807 Fan Connector (3-Pin

    DGND M_DATA(3) M_DATA(12) DGND M_DATA(13) M_DATA(8) DGND M_DATA(9) M_DM(1) DGND DGND M_DQS#(1) M_CLK_DDR0 M_DQS(1) M_CLK_DDR0# DGND DGND M_DATA(10) M_DATA(14) M_DATA(11) M_DATA(15) DGND DGND DGND DGND M_DATA(16) M_DATA(20) M_DATA(17) M_DATA(21) DGND DGND M_DQS#(2) PM_EXTTS#0 M_DQS(2) M_DM(2) C-12 Qosmio F40/F45 Maintenance Manual...
  • Page 235 M_A(9) M_A(7) M_A(8) M_A(6) +V1.8 +V1.8 M_A(5) M_A(4) M_A(3) M_A(2) M_A(1) M_A(0) +V1.8 +V1.8 M_A(10) MA_BS1# MA_BS0# MA_RAS# M_WE# M_CS0# +V1.8 +V1.8 M_CAS# M_ODT0 M_CS1# M_A(13) +V1.8 +V1.8 M_ODT1 DGND DGND M_DATA(32) M_DATA(36) M_DATA(33) M_DATA(37) Qosmio F40/F45 Maintenance Manual C-13...
  • Page 236 M_CLK_DDR1# M_DQS#(6) DGND M_DQS(6) M_DM(6) DGND DGND M_DATA(50) M_DATA(54) M_DATA(51) M_DATA(55) DGND DGND M_DATA(56) M_DATA(60) M_DATA(57) M_DATA(61) DGND DGND M_DM(7) M_DQS#(7) DGND M_DQS(7) M_DATA(58) DGND M_DATA(59) M_DATA(62) DGND M_DATA(63) ICH_3S_SMDATA DGND ICH_3S_SMCLK N$860610 +V3S N$860611 C-14 Qosmio F40/F45 Maintenance Manual...

  • Page 237: Express Card Connector (26-Pin

    Table C-27 PCMCIA Connector Pin Assignments (68-Pin) Pin No. Signal Name Pin No. Signal Name DGND ACARD_3S_AD0 ACARD_3S_AD1 ACARD_3S_AD3 ACARD_3S_AD5 ACARD_3S_AD7 ACARD_3S_CBE0# ACARD_3S_AD9 ACARD_3S_AD11 ACARD_3S_AD12 ACARD_3S_AD14 ACARD_3S_CBE1# ACARD_3S_PAR ACARD_3S_PERR# ACARD_3S_GNT# ACARD_3S_INT# ACARDVCC ACARDVPP N$965384 ACARD_3S_IRDY# ACARD_3S_CBE2# ACARD_3S_AD18 ACARD_3S_AD20 ACARD_3S_AD21 ACARD_3S_AD22 ACARD_3S_AD23 Qosmio F40/F45 Maintenance Manual C-15...

  • Page 238: Cn811 Ddr2 Dimm1 Socket (200-Pin

    Table C-28 DDR2 DIMM1 Socket Pin Assignments (200-Pin) Pin No. Signal Name Pin No. Signal Name M_VREF DGND DGND M_DATA(4) M_DATA(0) M_DATA(5) M_DATA(1) DGND DGND M_DM(0) M_DQS#(0) DGND M_DQS(0) M_DATA(6) DGND M_DATA(7) M_DATA(2) DGND M_DATA(3) M_DATA(12) C-16 Qosmio F40/F45 Maintenance Manual...
  • Page 239 M_DATA(19) M_DATA(23) DGND DGND M_DATA(24) M_DATA(28) M_DATA(25) M_DATA(29) DGND DGND M_DM(3) M_DQS#(3) M_DQS(3) DGND DGND M_DATA(26) M_DATA(30) M_DATA(27) M_DATA(31) DGND DGND M_CKE2 M_CKE3 +V1.8 +V1.8 MB_BS2# M_A(14) +V1.8 +V1.8 M_A(12) M_A(11) M_A(9) M_A(7) M_A(8) M_A(6) Qosmio F40/F45 Maintenance Manual C-17...
  • Page 240 DGND M_DATA(38) M_DATA(34) M_DATA(39) M_DATA(35) DGND DGND M_DATA(44) M_DATA(40) M_DATA(45) M_DATA(41) DGND DGND M_DQS#(5) M_DM(5) M_DQS(5) DGND DGND M_DATA(42) M_DATA(46) M_DATA(43) M_DATA(47) DGND DGND M_DATA(52) M_DATA(48) M_DATA(53) M_DATA(49) DGND DGND M_CLK_DDR3 DGND M_CLK_DDR3# M_DQS#(6) DGND C-18 Qosmio F40/F45 Maintenance Manual...

  • Page 241: Sata Hdd-2 Connector (22-Pin

    Signal Name Pin No. Signal Name DGND SATA_C_TXP1 SATA_C_TXN1 DGND SATA_RXN1 SATA_C_RXP1 DGND DGND DGND DGND +V5S +V5S +V5S DGND DGND C.30 CN813 Mini Card Connector (52-Pin) Table C-30 Mini Card Connector Pin Assignments (52-Pin) Qosmio F40/F45 Maintenance Manual C-19...

  • Page 242: Cn814 Bcas Card Connector (10-Pin

    USB_P5+ +V3S DGND +V3S DGND +V1.5S DGND +V3S C.31 CN814 BCAS Card Connector (10-Pin) Table C-31 BCAS Cad Connector Pin Assignments (10-Pin) Pin No. Signal Name Pin No. Signal Name BCASF-P5V BCRST-P5N XBCCLK-P5P DGND BCIO-P5P C-20 Qosmio F40/F45 Maintenance Manual...

  • Page 243: Odd Connector (50-Pin

    PIDE_3S_CS#(1) +V5S +V5S +V5S +V5S +V5S DGND DGND DGND DGND N$630734 DGND DISK_IN C.33 CN817 IEEE 1394 Connector (4-Pin) Table C-33 IEEE 1394 Connector Pin Assignments (4-Pin) Pin No. Signal Name Pin No. Signal Name Qosmio F40/F45 Maintenance Manual C-21...

  • Page 244: Cn818 Sata Hdd-1 Connector (22-Pin

    N$1040717 N$1188781 DGND N$1003370 BATT_DATA BATT_CLK DGND DGND C.36 CN1000 LED Board Connector (28-Pin) Table C-36 LED Board Connector Pin Assignments (28-Pin) Pin No. Signal Name Pin No. Signal Name +V5A +V5S +V3LA +V3A +V3S C-22 Qosmio F40/F45 Maintenance Manual...

  • Page 245: Cn2003 Tv Tuner Master Connector (124-Pin

    TMA-P5V TMA-P5V TMA-P5V TMA-P5V TMA-P5V TMA-P5V TMA_GND TMA_GND TMA_GND TMA_GND TMA_GND TMA_GND DGND PCI_3S_INTE# TMA-P5V TM-P3V PCI_3S_INTD# X33TU2-P3P N$1051338 DGND X33TU1-P3P N$1051347 DGND TM-P3V PCI_3S_REQ#(0) PCI_3S_GNT#(0) TM-P3V DGND PCI_3S_AD(31) /PCI_3S_AD(29) PCI_3S_GNT#(1) DGND PCI_3S_AD(30) PCI_3S_AD(27) TM-P3V Qosmio F40/F45 Maintenance Manual C-23...
  • Page 246 PCI_3S_AD(11) PCI_3S_AD(10) DGND DGND PCI_3S_AD(9) PCI_3S_AD(8) PCI_3S_CBE#(0) PCI_3S_AD(7) TM-P3V TM-P3V PCI_3S_AD(6) PCI_3S_AD(5) PCI_3S_AD(4) BCRSTM-P3N PCI_3S_AD(2) PCI_3S_AD(3) PCI_3S_AD(0) +V5S +V5S PCI_3S_AD(1) CPDETM-P3N DGND KBC_AGND BCIO-P5P TV1-TPM0 CPGP2M-P3P TV1-TPM1 CPGP1M-P3P TV1-TPM2 CPGP0M-P3P TV1-TPM0 BCCDET-P3N CPGP3M-P3P DGND DGND C-24 Qosmio F40/F45 Maintenance Manual...

  • Page 247: Cn2009 Tv Tuner Slave Connector (124-Pin

    DGND PCI_3S_INTE# TSA-P5V TS-P3V PCI_3S_INTF# X33TU4-P3P N$1187079 DGND X33TU3-P3P N$1106904 DGND TS-P3V PCI_3S_REQ#(3) PCI_3S_GNT#(3) TS-P3V DGND PCI_3S_AD(31) /PCI_3S_AD(29) PCI_3S_GNT#(1) DGND PCI_3S_AD(30) PCI_3S_AD(27) TS-P3V PCI_3S_AD(25) PCI_3S_AD(28) PCI_3S_REQ#(1) PCI_3S_AD(26) PCI_3S_CBE#(3) PCI_3S_AD(24) PCI_3S_AD(23) N$1106878 DGND DGND PCI_3S_AD(21) PCI_3S_AD(22) Qosmio F40/F45 Maintenance Manual C-25...
  • Page 248 TS-P3V TS-P3V PCI_3S_AD(6) PCI_3S_AD(5) PCI_3S_AD(4) BCRSTM-P3N PCI_3S_AD(2) PCI_3S_AD(3) PCI_3S_AD(0) +V5S +V5S PCI_3S_AD(1) CPDETM-P3N DGND KBC_AGND BCIO-P5P TV2-TPM0 CPGP2M-P3P TV2-TPM1 CPGP1M-P3P TV2-TPM2 CPGP0M-P3P TV2-TPM0 BCCDET-P3N CPGP3M-P3P DGND DGND XBCLKM-P3P DGND DGND DGND DGND DGND BCPWON-P3P +V5S C-26 Qosmio F40/F45 Maintenance Manual...

  • Page 249: Cn3000 Touch Pad Board To Module Connector (12-Pin

    Table C-41 TV Tuner Connector Pin Assignments (8-Pin) Pin No. Signal Name Pin No. Signal Name TVGND EXCVB1-PXP TVGND EXINL-PXP EXINR-PXP TVGND TVGND C.42 CN4001 Audio Board to M/B Connector (20-Pin) Table C-42 Audio Board to M/B Connector Pin Assignments (20-Pin) Qosmio F40/F45 Maintenance Manual C-27...

  • Page 250: Cn5000 Hot Key Board To M/B Connector (16-Pin

    LED Board to M/B Connector (28-Pin) Table C-44 LED Board to M/B Connector Pin Assignments (28-Pin) Pin No. Signal Name Pin No. Signal Name +V5A_LB +V5S_LB +V3LA_LB +V3A_LB +V3_LB +V3S_LB LED_GROUND DCIN_BLED#_DB PWR_BUF_BLED#_DB PWR_BUF_OLED#_DB BAT0_BLED#_DB BAT0_OLED#_DB HDD_LED#_DB ODD_LED#_DB C-28 Qosmio F40/F45 Maintenance Manual...

  • Page 251: Cn7000 Volume Board To M/B Connector (8-Pin

    Table C-47 IR Blaster-1 Connector Pin Assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name DGND N$1163007 DGND IRTX1-DET# DGND DGND C.48 JACK802 RJ45 LAN Connector (12-Pin) Table C-48 RJ45 LAN Connector Pin Assignments (12-Pin) Qosmio F40/F45 Maintenance Manual C-29...

  • Page 252: Jack4000 External Microphone Connector (6-Pin

    AGROUND_AUDIO N$1099615 N$1099617 LINE_S#_AB AGROUND_AUDIO C.51 JACK4002 Head Phone Connector (9-Pin) Table C-51 Head Phone Connector Pin Assignments (9-Pin) Pin No. Signal Name Pin No. Signal Name AUDIO_GROUND N$1183097 N$1183098 HPS_AB N$1099639 SPDIF_AB +V5S_SPDIF_AB AUDIO_GROUND C-30 Qosmio F40/F45 Maintenance Manual...

  • Page 253: Jack4003 Video In Connector (6-Pin

    Appendices Apx. C Pin Assignments C.52 JACK4003 Video In Connector (6-Pin) Table C-52 Video In Connector Pin Assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name EXCVB1-PXP N$1139468 N$1139473 TVGND Qosmio F40/F45 Maintenance Manual C-31...
  • Page 254 Apx. D Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Note Keytop Make Break Make Break ‘ ~ 7 & BkSp Qosmio F40/F45 Maintenance Manual...
  • Page 255 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) Qosmio F40/F45 Maintenance Manual...
  • Page 256 Appendices Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → Qosmio F40/F45 Maintenance Manual...
  • Page 257 5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. 8. * 205~207 are for JAPAN keyboard only Qosmio F40/F45 Maintenance Manual...
  • Page 258 Shift key, scan codes are changed as listed below: With left Shift With right Shift Set 1 E0 AA __________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12 ________ E0 F0 59 E0 12 ___________ E0 59 Qosmio F40/F45 Maintenance Manual...
  • Page 259 Code set 2 Make Break Make Break ← Home ↑ ↓ PgUp PgDn → Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break CTRL LALT ARROW NUMERIC Scrl Qosmio F40/F45 Maintenance Manual...
  • Page 260 Code set 1 Code set 2 Make Break Make Break (–) Table D-6 No.124 key scan code Shift Code set 1 Code set 2 Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + Qosmio F40/F45 Maintenance Manual...
  • Page 261 Keyboard Scan/Character Codes Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. Qosmio F40/F45 Maintenance Manual...

  • Page 262: Appendix E Key Layout

    Apx. E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout United States (US) Keyboard Figure E-1 US keyboard Japan (JP) Keyboard Figure E-2 JP keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 263 Appendices Apx. E Key Layout Spanish (SP) Keyboard Figure E-3 SP keyboard Korean (KR) Keyboard Figure E-4 KR keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 264 Apx. E Key Layout Appendices Canadian Bilingual (QB) Keyboard Figure E-5 QB keyboard French (FR) Keyboard Figure E-6 FR keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 265 Appendices Apx. E Key Layout German (GR) Keyboard Figure E-7 GR keyboard Italian (IT) Keyboard Figure E-8 IT keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 266 Apx. E Key Layout Appendices Taiwan (TC) Keyboard Figure E-9 TC keyboard E.10 Portuguese (PT) Keyboard Figure E-10 PT keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 267 Appendices Apx. E Key Layout E.11 DU, UE, US International (USE) Keyboard Figure E-11 USE keyboard E.12 Arabic (AR) Keyboard Figure E-12 AR keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 268 Apx. E Key Layout Appendices E.13 Belgian (BE) Keyboard Figure E-13 BE keyboard E.14 Russian (RU) Keyboard Figure E-14 RU keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 269 Appendices Apx. E Key Layout E.15 Swiss/Switzerland (SL) Keyboard Figure E-15 SL keyboard E.16 Swedish (SW) Keyboard Figure E-16 SW keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 270 Apx. E Key Layout Appendices E.17 Norwegian (NO) Keyboard Figure E-17 NO keyboard E.18 Danish (DK) Keyboard Figure E-18 DK keyboard Qosmio F40/F45 Maintenance Manual...
  • Page 271 Appendices Apx. E Key Layout E.19 Turkey (TR) Keyboard Figure E-19 TR keyboard E.20 Greek (GK) Keyboard Figure E-20 GK keyboard E-10 Qosmio F40/F45 Maintenance Manual...
  • Page 272 Apx. E Key Layout Appendices E.21 Canadian Multinational (CM) Keyboard Figure E-21 CM keyboard E.22 Herbrew (HE) Keyboard Figure E-22 HE keyboard Qosmio F40/F45 Maintenance Manual E-11...
  • Page 273 Appendices Apx. E Key Layout E.23 Czech (CZ) Keyboard Figure E-23 CZ keyboard E.24 Scandinavian (N5) Keyboard Figure E-24 N5 keyboard E-12 Qosmio F40/F45 Maintenance Manual...
  • Page 274 Apx. E Key Layout Appendices E.25 Hungary (HU) Keyboard Figure E-25 HU keyboard E.26 Slovakian (SK) Keyboard Figure E-26 SK keyboard Qosmio F40/F45 Maintenance Manual E-13...
  • Page 275 Appendices Apx. E Key Layout E.27 Yugoslavia (YU) Keyboard Figure E-27 YU keyboard E.28 Thai (TH) Keyboard Figure E-28 TH keyboard E-14 Qosmio F40/F45 Maintenance Manual...
  • Page 276 Apx. E Key Layout Appendices E.29 United Kingdom (EN) Keyboard Figure E-29 EN keyboard E.30 Turkish F (TF) Keyboard Figure E-30 TF keyboard Qosmio F40/F45 Maintenance Manual E-15...

  • Page 277: Appendix F Bios Rewrite Procedures

    ] key (on the left of the space key). (Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset. Qosmio F40/F45 Maintenance Manual...
  • Page 278 5. Normally it takes about 30 seconds to rewrite the EC/KBC. It may take 3 minutes (maximum), depending on the conditions of the computer or ICs. The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed. Qosmio F40/F45 Maintenance Manual...

This manual is also suitable for:

Qosmio f45

Table of Contents