Siemens Open Processor Owner's Manual page 64

Open Processor with Trane Driver Owner's Manual
B B B B . . . . A A A A ll ll ll ll po po poi i i i n n n n t t t t s s s s a a a a dd po
1. Verify that the points have the correct addresses and that there are no duplicate
addresses.
2. Check that points are defined with the proper type, slope, and intercept. Refer to
Chapter 4, Point Databases, for more information.
3. Verify that all physical connections are secure.
4. Contact your local Siemens Building Technologies representative.
C C C C . . . . S S S S o o o o m m m m e o e or r r r a a a a ll ll ll ll po e o e o
v v v v a a a a l l l l ue ues s s s . . . .
ue ue
1. Verify that the points have the correct addresses and that there are no duplicate
addresses.
2. Check that the points are defined with the proper type, slope, intercept, etc. Refer
to Chapter 4, Point Databases, for more information.
3. Contact your local Siemens Technologies, Inc. representative.
4. Contact a Trane representative to ensure that the Trane system has been installed
and certified, and that it is operating according to their procedures.
D D D D . . . . A A A A g g g g r r r r oup o oup o oup o oup of f f f po
a a a a ppe ppea a a a r r r r s s s s a a a a s s s s f f f f a a a a il il il iled
ppe ppe
1. Verify that the points have the correct address and that there are no duplicate
addresses.
2. Check that the points are defined with the proper type, slope, intercept, etc. Refer
to Chapter 4, Point Databases, for more information.
3. Check that the Metapoint status appears as normal (-N-).
4. Contact a Trane representative to ensure that the Trane system has been installed
and certified, and that it is operating according to their procedures.
5. Contact your local Siemens Technologies, Inc. representative.
E E E E . . . . A A A A ll ll ll ll po po po poi i i i n n n n t t t t s s s s a a a a dd
1. Verify that the points have the correct addresses and that there are no duplicate
addresses.
2. Check that points are defined with the proper type, slope, and intercept. Refer to
Chapter 4, Point Databases, for more information.
3. Verify that all physical connections are secure.
4. Verify baud rates of FLN port.
5. Contact your local Siemens Building Technologies representative.
6-6
ddr r r r e e e e ss ss ss ssed dd dd ed i i i i n n n n t t t t he ed ed he he he O O O O pen pen pen P P P P r r r r o o o o c c c c e e e e ss ss ss sso o o o r r r r a a a a ppe pen
poi i i i n n n n t t t t s s s s a a a a dd po po dd ddr r r r e e e e ss ss ss ssed dd ed ed i i i i n n n n t t t t he ed
po poi i i i n n n n t t t t s s s s a a a a ss ss ss sso o o o c c c c i i i i a a a a t t t t ed po ed ed w w w w i i i i t t t t h h h h a a a a s s s s pe ed
ed ( ( ( ( * * * * F F F F * * * * ). ). ). ).
ed ed
dd dd ddr r r r e e e e ss ss ss ssed ed ed ed i i i i n n n n t t t t he he he O O O O pen he pen P P P P r r r r o o o o c c c c e e e e ss ss ss sso o o o r r r r a a a a ppe pen pen
ppe ppe ppea a a a r r r r a a a a s s s s f f f f a a a a il il il iled
he he O O O O pen he pen P P P P r r r r o o o o c c c c e e e e ss ss ss sso o o o r r r r d d d d is is is isp p p p l l l l a a a a y i y i y i y in n n n c c c c o o o o rr rr rr rre e e e c c c c t t t t pen pen
pec c c c i i i i f f f f i i i i c c c c T T T T r r r r a a a a ne equ pe pe ne equi i i i p p p p m m m m en ne equ ne equ
ppe ppe ppea a a a r r r r a a a a s s s s f f f f a a a a il il il iled
Siemens Building Technologies, Inc.
ed ( ( ( ( * * * * F F F F * * * * ). ). ). ). ed ed
ent t t t c c c c on en en ontr tr tr tro o o o ll ll ll lle e e e r r r r on on
ed ( ( ( ( * * * * F F F F * * * * ). ). ). ). ed ed
Landis Division