Siemens Open Processor Owner's Manual page 30

Open Processor with Trane Driver Owner's Manual
x
Program names should be the same as the point names and equipment they control,
but without the suffix. For example:
E E E E q q q q u u u u i i i i p p p p m m m m en
P P P P r r r r og
P P P P o o o o i i i i n n n n t t t t s s s s C C C C on
S S S S a a a a vi vi vi ving ng t t t t i i i i m m m m e e e e w w w w hen en hen ent t t t e e e e r r r r i i i i ng po
ng ng hen en hen en
Instead of typing an entire point name, the system allows the following shortcuts:
x
Wildcards allow for easier selection for names of points.
x
Query for point names can provide a numeric list of points to select from.
x
The quick text key can be used to define part of the point name.
x
Use command key shortcuts (such as C C C C tr tr tr trl l l l -P P P P and C C C C tr tr tr trl l l l -I I I I from the paste buffer).
For examples of queries and wildcarding, refer to the Introduction chapter of the System 600
APOGEE Field Panel User's Manual (125-3000).
P P P P o o o o i i i i n n n n t t t t a a a a dd ddr r r r e e e e ss ss ss ss
dd dd
The Open Processor uses the standard Siemens Building Technologies addressing scheme
of TCCLDDPP. Refer to Table 4-2.
A A A A bb bbr r r r e e e e v v v v i i i i a a a a t t t t i i i i on
bb bb
T
CC
L
4-6
ent t t t : : : : Building 990, Floor 1, Air Handling Unit 1
en en
,/1%/'<<31)/5341$+834
ogr r r r a a a a m m m m N N N N a a a a m m m m e e e e : : : :
og og
,/1%/'<<31)/5341$+83416$7
on ontr tr tr tro o o o ll ll ll lle e e e d d d d : : : : on
,/1%/'<<31)/5341$+8341+9/
,/1%/'<<31)/5341$+83416)1
ng poi i i i n n n n t t t t n n n n am ame e e e s s s s
ng po ng po am am
T T T T a a a a b b b b l l l l e e e e 4 4 4 4 - - - - 2 2 2 2 . . . . O O O O p p p p en en P P P P r r r r o o o o c c c c e e e e ss ss ss sso o o o r r r r P P P P o o o o i i i i n n n n t t t t A A A A dd
en en
on M M M M e e e e a a a a n n n n i i i i ng ng R R R R a a a a nge
on on ng ng
Trunk 0–3
Cabinet 00–99
FLN 0–3
ddr r r r e e e e ss ss ss ssi i i i ng ng S S S S c c c c he hem m m m e e e e . . . .
dd dd ng ng he he
nge D D D D e e e e s s s s c c c c r r r r i i i i p p p p t t t t i i i i on
nge nge
As with other MBC or SCU
controllers, the individual building
level network (BLN) number is
always zero.
The cabinet number assigned to
the Open Processor (unique BLN
network node address).
N N N N O O O O T T T T E E E E : : : : It is possible to have more
than one node in an enclosure.
0: Virtual or PTM points
1–3: Trane points
c c c c on ont t t t i i i i nue
on on
on
on on
nued d d d on ne on nex x x x t t t t p p p p a a a a ge ge... ... ... ...
nue nue on ne on ne ge ge
Siemens Building Technologies, Inc.
Landis Division