Page 1 Toshiba Personal Computer Satellite T110DD/Satellite ProT110DD/PORTEGE T110DD Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 2 © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.
Page 3 NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.
Page 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite T110D, Satellite Pro T110D, PORTEGE T110D system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
Page 5 Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations.
Page 6: Table Of Contents
Table of Contents Chapter 1 Hardware Overview Features ..........................1 System Block Diagram ....................6 2.5-inch Hard Disk Drive....................9 Keyboard........................12 TFT Color Display.......................13 1.5.1 LCD Module with CCFL Backlight .............13 Power Rails ........................14 Batteries ........................15 1.7.1 Main Battery ....................15 1.7.2 Battery Charging Control................15 1.7.3 RTC battery....................17 AC Adapter ........................18 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 7 Chapter 2 Troubleshooting Procedures Troubleshooting ......................1 Troubleshooting Flowchart................... 2 Power Supply Troubleshooting..................6 Procedure 1 Power Status Check .................. 6 Procedure 2 Connection Check..................8 Procedure 3 Charging Check ..................8 Procedure 4 Replacement Check ................10 System Board Troubleshooting................... 11 Procedure 1 Message Check ..................
Page 8 2.10 Wireless LAN Troubleshooting...................26 Procedure 1 Transmitting-Receiving Check ..............26 Procedure 2 Antennas' Connection Check ..............27 Procedure 3 Replacement Check .................28 2.11 Sound Troubleshooting....................29 Procedure 1 Connector Check..................29 Procedure 2 Replacement Check .................30 2.12 Bluetooth Troubleshooting ..................31 Procedure 1 Connector Check and Replacement Check..........31 2.13 HDMI Troubleshooting ....................32 Procedure 1 Connector Check and Replacement Check..........32...
Page 9 Procedure 2 Connect Check and Replacement Check ..........40 2.20 LED Troubleshooting ....................41 Procedure 1 Each function Execution Check.............. 41 Procedure 2 Connect Check and Replacement Check ..........41 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 10 Chapter 3 Diagnostic Programs Tests and Diagnostics Software Overview ..............2 Executing the Diagnostic Test ..................3 Subtest names.........................7 System Test........................10 Memory Test........................17 Keyboard Test......................21 Display Test .........................24 Hard Disk Test ......................39 Real Time Clock Test ....................42 3.10 Cache Memory Test.....................44 3.11 High Resolution Display Test..................46 3.12 Multimedia Test ......................52...
Page 11 Chapter 4 Replacement Procedures Overview........................1 Safety Precautions......................2 Before You Begin ......................3 Disassembly Procedure ....................4 Assembly Procedure...................... 5 Tools and Equipment ....................5 Screw Tightening Torque....................6 Screw Notation ......................7 Battery pack ........................8 HDD..........................11 Memory Module ......................
Page 12 Appendix Appendix A Handling the LCD Module ................1 Appendix B Board Layout .....................1 Appendix C Pin Assignments....................1 Appendix D Keyboard Scan/Character Codes ...............1 Appendix E Key Layout......................1 Appendix F Wiring Diagrams....................1 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 13: Chapter 1 Hardware Overview
Chapter 1 Hardware Overview Satellite T110/Satellite ProT110/PROTEGE T110 Maintenance Manual (960-Q08)
Page 14 Chapter1 Hardware Overview Hardware Overview Chapter 1 Contents Features ......................... 1 System Block Diagram ....................5 2.5-inch Hard Disk Drive....................8 Keyboard........................11 TFT Color Display...................... 12 Power Rails ......................... 13 Batteries ........................14 1.7.1 Main Battery..................14 1.7.2 Battery Charging Control ..............15 1.7.3 RTC battery ...................
Page 15 Chapter1 Hardware Overview Figures Figure 1-1-1 Left of the computer..................3 Figure 1-1-2 Right of the computer ..................4 Figure 1-2-1 System Block Diagram for Intel Platform ............5 Figure 1-3-1 2.5-inch HDD ....................9 Figure 1-4-1 Keyboard for US Style..................12 Figure 1-5-1 LCD Module…………...
Page 16: Features
Chapter 1 Hardware Overview 1.1 Features The Satellite T110D/Satellite Pro T110D/PROTÉGÉ T110D (AMD Platform) features are listed below. Microprocessor Microprocessor that is used will be different by the model. It supports processors as follows -1.6GHz (18W), Turion X2 Neo Dual-Core Processor L625 -1.5GHz (18W), Athlon X2 Neo Dual-Core Processor L325 -1.6GHz (15W), Athlon Neo MV-40 Memory...
Page 17 Chapter 1 Hardware Overview Keyboard module has 85 or 86 keys and support optional Windows and application Keys Battery The RTC battery is equipped inside the computer. The main battery is a detachable lithium ion battery. 6 cell Li-Ion 10.8v/4800mAh USB (Universal Serial Bus) 3 USB ports are provided.
Page 18: Figure 1-1-1 Left Of The Computer
Chapter 1 Hardware Overview Kensington Lock, Hard Disk Drive Password 3D Accelerometer for Hard Disk Drive 1. Extend Monitor connector 2. FAN HOLE 3. Bridge Media Slot 4. HDMI out port 5. USB port (USB Sleep and Charge function is supported by this port only.) 6.
Page 19: Figure 1-1-2 Right Of The Computer
Chapter 1 Hardware Overview 1. Headphone Jack 2. Microphone jack 3. USB port 4. LAN jack 5. DC-IN jack Figure 1-1-2 Right of the computer Satellite T110D / Satellite Pro T110D /PROTEGE110D Maintenance Manual (960-Q08)
Page 20: System Block Diagram
Chapter 1 Hardware Overview 1.2 System Block Diagram Figure 1-2-1 shows the system block diagram. Figure 1-2-1 System block diagram for AMD Platform Satellite T110D / Satellite Pro T110D /PROTEGE110D Maintenance Manual (960-Q08)
Page 21 Chapter 1 Hardware Overview The PC contains the following components. -1.6GHz (18W), Turion X2 Neo Dual-Core Processor L625 -1.5GHz (18W), Athlon X2 Neo Dual-Core Processor L325 -1.6GHz (15W), Athlon Neo MV-40 Memory Two memory slots capable of accepting DDRII-SDRAM 1GB, 2GB or 4GB memory modules for a maximum of 8GB.
Page 22 Chapter 1 Hardware Overview  USB Controllers(5 OHCI and 2 EHCI to support 12 USB2.0 ports and 2 dedicated USB1.1 ports)  RTC  GPIO  ACPI Power Management3.0  SMBus 2.0 Controller  High Definition Audio Controller  528-pin 21mm x 21mm FCBGA Packag Other main system chips •...
Page 23: Inch Hard Disk Drive
Chapter 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm contains 2.5-inch magnetic disks and magnetic heads. Figure 1-3-1 shows a view of the 2.5-inch HDD and Tables 1-3-2 and 1-3-3 list the specifications.
Page 24: Table 1-3-2 2.5-Inch Hdd Dimensions
Chapter 1 Hardware Overview Standard value Parameter WD2500BEVT-26ZCT0 WD3200BEVT-26ZCT0 Width (mm) 69.85 Outline Height (mm) dimensions Length (mm) 100.0 99(Max) Weight (g) Table 1-3-2 2.5-inch HDD dimensions Specification Parameter TOS MK2555GSX TOS MK3255GSX TOS MK5055GSX Storagesize 250GB 320GB 500GB (formatted) Speed (RPM) 5400 Data transfer Rate...
Page 25: Table 1-3-3 2.5-Inch Hdd Specification
Chapter 1 Hardware Overview Specification Parameter WD2500BEVT-26ZCT0 WD3200BEVT-26ZCT0 Storage size 250GB 320GB (formatted) Speed (RPM) 5,400 Data transfer Rate - To/From Media 933MB/s Max. - T0/From Host 3Gb/s bus transfer rate 3Gb/s Average random seek 12.0ms/13.0ms time (read) (ms) Power-on-to-ready 4.0 (typ) (sec) Table 1-3-3 2.5-inch HDD Specification...
Page 26: Keyboard
Chapter 1 Hardware Overview 1.4 Keyboard The Satellite T110D, Satellite Pro T110D, and PORTEGE T110D keyboard is for US style Figure 1-4-1 is a view of the keyboard for US style Figure 1-4-1 Keyboard for US style See Appendix E for details of the keyboard layout Satellite T110D / Satellite Pro T110D /PROTEGE110D Maintenance Manual (960-Q08)
Page 27: Tft Color Display
Chapter 1 Hardware Overview 1.5 TFT Color Display The Satellite T110 use LED to control backlight. LCD Module Figure 1-5-1 shows a view of the LCD module and Table 1-5-2 lists the specifications. Figure 1-5-1 LCD Module Specifications(WXGA+) Item SAMSUNGA CHI MEI LTN116AT01-T01 N116B6-L02...
Page 28: Power Rails
Chapter 1 Hardware Overview 1.6 Power Rails Table 1-6-1 lists the power rail output specifications of Congo platform. Power supply （Yes/No） Name Power OFF Power OFF Voltage [V] No Battery Suspend mode Boot mode +5VPCU +3VPCU +3V_S5 +3VSUS +1.8VSUS +SMDDR_VTERM +SMDDR_VREF +1.8V +1.5V...
Page 29: Batteries
Chapter 1 Hardware Overview 1.7 Batteries The PC has the following two batteries. Main battery Real time clock (RTC) battery Table 1-7-1 lists the specifications for these two batteries. Battery Name Battery Element Output Voltage 6 Cells Lithium ion 10.8 V Main battery Real time clock COIN Type...
Page 30: Battery Charging Control
Chapter 1 Hardware Overview 1.7.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and detects a full charge when the AC adaptor and battery are connected to the computer. Battery Charge When the AC adapter is connected, normal charging is used while the system is turned on and quick charge is used while the system is turned off.
Page 31: Rtc Battery
Chapter 1 Hardware Overview 1.7.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-7-4 lists the Time required for charges of RTC battery and data preservation time. Condition Time Charging time...
Page 32: Ac Adapter
Chapter 1 Hardware Overview 1.8 AC Adapter The AC adapter is used to charge the battery. Table 1-8-1 lists the AC adapter specifications. Parameter Specification With Led DELTA/ LITE-ON DELTA/ LITE-ON 2pin 3pin Power Input voltage AC 100V/240V Input frequency 50Hz/60Hz ≦1.5A Input current...
Page 33: Chapter 2 Troubleshooting Procedures
Chapter 2 Troubleshooting Procedures Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 34 Chapter 2 Troubleshooting Procedures Chapter 2 Contents Chapter 2 Contents Troubleshooting ......................1 Troubleshooting Flowchart................... 2 Power Supply Troubleshooting..................6 Procedure 1 Power Status Check ..............6 Procedure 2 Connection Check..............8 Procedure 3 Charging Check ................ 8 Procedure 4 Replacement Check ..............
Page 35 Chapter 2 Troubleshooting Procedures LAN Troubleshooting....................25 Procedure 1 Diagnostic Test Program Execution Check ......25 Procedure 2 Connector Check and Replacement Check......25 2.10 Wireless LAN Troubleshooting.................. 26 Procedure 1 Transmitting-Receiving Check ..........26 Procedure 2 Antennas' Connection Check ..........27 Procedure 3 Replacement Check ..............
Page 36 Chapter 2 Troubleshooting Procedures 2.19 USB Troubleshooting ....................40 Procedure 1 Diagnostic Test Program Execution Check ......40 Procedure 2 Connect Check and Replacement Check ........ 40 2.20 LED Troubleshooting ....................41 Procedure 1 Each function Execution Check..........41 Procedure 2 Connect Check and Replacement Check ........
Page 37: Troubleshooting
The implement for the Diagnostics procedures is referred to Chapter 3. Also, following implements are necessary: 1. Phillips screwdrivers (For replacement procedures) 2. Implements for debugging port check  Toshiba Free-DOS system Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 38: Troubleshooting Flowchart
Before going through the flowchart steps, verify the following:  Ask customer to enter the password if a password is registered.  Verify with the customer that Toshiba Windows is installed on the hard disk. Non- Windows operating systems can cause the computer to malfunction.
Page 39 Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (1/2) Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 40 Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (2/2) If the diagnostics program cannot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error(s), and then perform the appropriate troubleshooting procedures as follows: 1.
Page 41 Chapter 2 Troubleshooting Procedures 4. If an error is found on the touch pad test, perform the Touch pad Troubleshooting Procedures in Section 2.7. 5. If an error is detected on the display test, perform the Display Troubleshooting Procedures in Section 2.8. 6.
Page 42: Power Supply Troubleshooting
Chapter 2 Troubleshooting Procedures Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Power Status Check Procedure 2: Connection Check Procedure 3: Charging Check...
Page 43 Chapter 2 Troubleshooting Procedures *1 When the power supply controller detects a malfunction, the DC IN icon blinks orange and perform the following procedure. When the icon is blinking, perform the following procedure. Remove the battery pack and the AC adapter. Re-attach the battery pack and the AC adapter.
Page 44: Procedure 2 Connection Check
Chapter 2 Troubleshooting Procedures Procedure 2 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the PCN1 connector and wall outlet.
Page 45 Chapter 2 Troubleshooting Procedures go to Procedure 4. Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 46: Procedure 4 Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follow the steps described in Chapter 4, Replacement Procedures.
Page 47: System Board Troubleshooting
Chapter 2 Troubleshooting Procedures System Board Troubleshooting This section describes how to determine if the system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2 Diagnostic Test Program Execution Check...
Page 48: Procedure 1 Message Check
Chapter 2 Troubleshooting Procedures Procedure 1 Message Check When the power is turned on, the system performs the Power on Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it. ...
Page 49: Procedure 3Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests.
Page 50: Hard Disk Drive Troubleshooting
For the backup, refer to the User’s Manual. Procedure 1 Partition Check Insert the Toshiba USB memory and start the computer. Perform the following checks: Check 1 Input C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Procedure 2.
Page 51: Procedure 2 Message Check
Chapter 2 Troubleshooting Procedures Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Turn on the computer and check the message on the screen.
Page 52: Procedure 3 Diagnostic Test Program Execution Check
Chapter 2 Troubleshooting Procedures Procedure 3 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program.
Page 53: Procedure 4 Connector Check And Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 4 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. The connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the computer following instructions in Chapter 4, Replacement Procedures and perform the following checks.
Page 54: Keyboard Troubleshooting
Chapter 2 Troubleshooting Procedures 2.6 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test in the Diagnostic Program.
Page 55: Procedure 2 Connector Check And Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure keyboard cable is firmly connected to system board.
Page 56: Touch Pad Troubleshooting
Chapter 2 Troubleshooting Procedures 2.7 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test in the Diagnostic Program.
Page 57: Procedure 2 Connector Check And Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the cable is firmly connected to system board.
Page 58: Display Troubleshooting
Chapter 2 Troubleshooting Procedures 2.8 Display Troubleshooting To check if the computer’s display is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check...
Page 59: Procedure 3 Connector And Cable Check
Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD cable. Their cables may be disconnected from system board. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. If the connection is loose, reconnect firmly and restart the computer.
Page 60: Procedure 4 Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check LCD module, LCD cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If characters or graphics on the internal display are not displayed clearly, perform Check 1.
Page 61: Lan Troubleshooting
Chapter 2 Troubleshooting Procedures 2.9 LAN Troubleshooting To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute LAN test in the LAN test program.
Page 62: Wireless Lan Troubleshooting
Chapter 2 Troubleshooting Procedures 2.10 Wireless LAN Troubleshooting To check if the computer's Wireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Procedure 2: Antennas' Connection Check Procedure 3: Replacement Check Procedure 1 Transmitting-Receiving Check Before starting the test, make sure wireless communication is enabled in BIOS setup Check 1...
Page 63: Procedure 2 Antennas' Connection Check
Chapter 2 Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless communication is Enabled in BIOS setup.
Page 64: Procedure 3 Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Wireless LAN antenna may be faulty.
Page 65: Sound Troubleshooting
Chapter 2 Troubleshooting Procedures 2.11 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Replacement Check Procedure 1 Connector Check The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection.
Page 66: Procedure 2 Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 2 Replacement Check  If External microphone/Headphone does not work properly, perform check 1.  If internal microphone /Speaker do not work properly, perform check 2.  If HP out does not work properly, perform check 3. ...
Page 67: Bluetooth Troubleshooting
Chapter 2 Troubleshooting Procedures 2.12 Bluetooth Troubleshooting To check if the computer’s Bluetooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1 Connector Check and Replacement Check The Bluetooth module is connected to system board. If Bluetooth malfunctions, its connection is defective or Bluetooth cable and system board may be faulty.
Page 68: Hdmi Troubleshooting
Chapter 2 Troubleshooting Procedures 2.13 HDMI Troubleshooting To check if the computer’s HDMI is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External HDMI Monitor Check Procedure 2: Connector and Cable Check Procedure 3: Replacement Check Procedure 1 Connector Check and Replacement Check The HDMI port is connected to system board.
Page 69: Procedure 3Connector And Cable Check
Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check HDMI monitor connected to HDMI&USB board by an HDMI cable. If the connection is loose, reconnect firmly and restart the computer. If the problem still occurs, go to Procedure 4. Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 70: Procedure 4Replacement Check
Chapter 2 Troubleshooting Procedures Procedure 4 Replacement Check HDMI signals are connected to display circuits via HDMI cable and HDMI&USB board. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If characters or graphics on the internal display are not displayed clearly, perform Check 1.
Page 71: Memory Troubleshooting
Chapter 2 Troubleshooting Procedures 2.14 Memory Troubleshooting Memory troubleshooting can following below procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connect Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Memory test in the Memory test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
Page 72: Troubleshooting
Chapter 2 Troubleshooting Procedures 2.15 3G Troubleshooting To check if the computer’s 3G is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1 Connector Check and Replacement Check The 3G module is connected to system board. If 3G malfunctions, its connection is defective or Antenna and system board may be faulty.
Page 73: Camera Troubleshooting
Chapter 2 Troubleshooting Procedures 2.16 Camera Troubleshooting To check if the computer’s Camera is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1: Camera Execution Check Procedure 2: Connect Check and Replacement Check Procedure 1 Camera Execution Check Open photo/video tool to look if there is an image.
Page 74: Microphone Troubleshooting
Chapter 2 Troubleshooting Procedures 2.17 Microphone Troubleshooting Microphone troubleshooting can following below procedures as instructed. Procedure 1: Sound Recorder Execution Check Procedure 2: Connect Check and Replacement Check Procedure 1 Sound Recorder Execution Check Open accessory to find sound recorder tool, try to record a length of sound, and then replay it to see if microphone is working normal.
Page 75 Chapter 2 Troubleshooting Procedures Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 76: Crt Troubleshooting
Chapter 2 Troubleshooting Procedures 2.18 CRT Troubleshooting To check if the computer’s CRT is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Connector and Cable Check Procedure 3: Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer’s external CRT port, and then to see if you can transfer video image to external monitor.
Page 77: Usb Troubleshooting
Chapter 2 Troubleshooting Procedures 2.19 USB Troubleshooting Flatiron Mini carries 3 USB port. To check if the computer’s USB port is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connect Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check...
Page 78: Led Troubleshooting
Chapter 2 Troubleshooting Procedures 2.20 LED Troubleshooting These are 9 LED lights at Top assy. From left to right, the Open statuses of them represent functions as below. 1. AC-IN 2. Power 3. Battery 4.HDD 5. Cardreader 6.W-Lan 7.3G 8.Arrow Lock 9.Number Lock To check if the computer’s LED is malfunctioning or not, follow the troubleshooting procedures below as instructed.
Page 79: Chapter 3 Diagnostic Programs
Test Program for Field. Chapter 3 Diagnostic Programs Satellite T110D and Satellite Pro T110D Tests and Diagnostics Manual...
Page 80: Tests And Diagnostics Software Overview
Test Program for Field. Chapter 3 Contents Tests and Diagnostics Software Overview ............3-3 Executing the Diagnostic Test ................3-4 Subtest names ......................3-8 System Test ......................3-11 Memory Test ......................3-18 Keyboard Test ...................... 3-22 Display Test ......................3-24 Floppy Disk Test ....................
Page 81: Tests And Diagnostics Software Overview
 A formatted working disk for the floppy disk drive test (all tests)  A CD test media (Toshiba Backup CD ROM for the CD-ROM test) The following sections detail the tests contained within the Diagnostic Test Menu. Refer to Sections 3.18, 3.19, 3.20 and, 3.21 for detailed information on the remaining functions of the...
Page 82: Executing The Diagnostic Test
1. You test disk is match this model , ex. disk is 14” but machine is 13” . 2. The M/B EEPROM project type is math your test disk , if not , please use WDMI3.EXE to modify with right LCD size . The following screen displays: TOSHIBA Satellite(Pro) T110 Diagnostics ::Select item Version v1.00 :Escape [ DIAGNOSTICS MENU ] 01.DIAGNOSTIC TEST...
Page 83 Test Program for Field. The following menu displays: TOSHIBA Satellite(Pro) T110 Diagnostics ::Select item Version V1.00 :Escape [ DIAGNOSTICS MENU ] 01. DIAGNOSTIC TEST 02. RUNNING TEST 03. DMI INFORMATION [ DIAGNOSTIC TEST MENU ] 04. LOG UTILITIES 05. SYSTEM CONFIGURATION 01.
Page 84 Test Program for Field. 4. Select the subtest you want to execute and press Enter. The following menu displays: TOSHIBA Satellite(Pro) T110 Diagnostics : :Select item Version V1.00 :Escape [ DIAGNOSTICS MENU ] [ SYSTEM TEST ] 01. DIAGNOSTIC TEST 02.
Page 85 Test Program for Field. NOTES: The Item2 and 3 of Test Parameter are not used by some tests. Go To Test Move the highlight bar to Go To Test and press Enter to start executing the test. Test Loop Select NO to return the screen to the subtest menu after the test is complete. Select YES to set the test to run continuously until it is halted by the user.
Page 86: Subtest Names
Test Program for Field. Subtest names Table 3-1 lists the subtest names for each test program in the Diagnostic Test menu. Table 3-1 Subtest Names(1/3) Test Name Subtest Name SYSTEM TEST FAN ON/OFF check Battery TEST CPU Temperature 3D HDD Protection Test (90d) MEMORY TEST Conventional Memory Protected Mode...
Page 87 Test Program for Field. Table 3-1 Subtest Names(2/3) Test Name Subtest Name FLOPPY DISK TEST Sequential Read Sequential W/R/C Random Address/Data Write Specified Address Read Specified Address HARD DISK TEST Sequential Read Address Uniqueness Random Address Data Cross Talk and Peek Shift Write Specified Address Read Specified Address Sequential Write...
Page 88 Test Program for Field. Table 3-1 Subtest Names(3/3) Test Name Subtest Name MULTIMEDIA TEST Sequential Read Test Random Read Test Read Specified Address Test 1 point W/R/C Test MEMORY2 All one/zero Test Walking 1/Walking 0 Test(Left) Walking 1/Walking 0 Test(Right) Walking 1/Walking 0 Test(Left /Right) *This test cannot support.
Page 89: System Test
Test Program for Field. System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains three subtests. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 FAN ON/OFF Checking Select 1,2,3 to control FAN on/off , 1=Fan on , 2=Fan off , 3=Exit .
Page 90 Test Program for Field. Subtest 03 CPU Temperature This will display CPU Temperature for check , press [ESC] to exit . [CPU_TEMP.EXE] Program Version : 1.3 03-09-2009 CPU Temperature : XX GPU Temperature : XX NOTES: If no external Graphics , GPU not report temperature . when read data is 255 mean no external Graphics .
Page 91 Test Program for Field. Test1 The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC Upper Judgment If all data is less than ranges, it will be OK.
Page 92 Test Program for Field. Test2 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Rear Uppe Judgment If all data is less than ranges, it will be OK. Satellite T110D and Satellite Pro T110D Tests and Diagnostics Manual...
Page 93 Test Program for Field. Test3 The display of a test program and the set method of PC are shown below. Display of a Test Program Right Set method of PC Uppe Judgment If all data is less than ranges, it will be OK. Satellite T110D and Satellite Pro T110D Tests and Diagnostics Manual...
Page 94 Test Program for Field. Test4 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Front Uppe Judgment If all data is less than ranges, it will be OK. Satellite T110D and Satellite Pro T110D Tests and Diagnostics Manual...
Page 95 Test Program for Field. Test5 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Left Uppe Judgment If all data is less than ranges, it will be OK. Judgment Inspection If all data is less than ranges, it will be OK.
Page 96: Memory Test
Test Program for Field. Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s memory. Move the highlight bar to the subtest you want to execute and press Enter.
Page 97 Test Program for Field. 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,...8000H, 8004H, through FFECH Subtest 02 Protected Mode...
Page 98 Test Program for Field. with the original data patterns. Addresses are displayed in 64KB increments during the test. Test Process: 1. Byte Enable Test One bit write/ 8 bit read” is executed and the new data is compared with the original data. Test data = CCAA5533H, 80000000H 2.
Page 99 Test Program for Field. Test Process: 1. Checks the memory size to determine the maximum size of installed memory. 2. Tests memory addresses 0 to the maximum installed. 3. Writes, reads, and compares test data after a memory refresh cycle (16ms or more).
Page 100: Keyboard Test
Test Program for Field. Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains five subtests that test the computer’s keyboard and mouse actions. Move the highlight bar to the subtest you want to execute and press Enter.
Page 101 Test Program for Field. Subtest 04 PS/2 Mouse (Pointing) This subtest checks the function of mouse as shown below. A) Pointing device (mouse) B) Mouse buttons Please move cursor to upper left and press left button , screen will display <PRESS>...
Page 102: Display Test
Test Program for Field. Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter.
Page 103 Test Program for Field. Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25).
Page 104 Test Program for Field. Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H - 7EH using Mode 03H (80*25). The data displayed is shifted 1 byte to the left for each line as shown below. 80*25 CHARACTER DISPLAY 01234567890123456789012345678901234567890123456789012345678901234567890123456789 !”#$%&’()*=,.-/0123456789:;?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_’abcdefghIjklmno...
Page 105 Test Program for Field. Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white. The screen below shows the displays when this subtest is executed. 320 * 200 GRAPHICS DISPLAY COLOR SET 0 : [ 4 ] GREEN...
Page 106 Test Program for Field. 320*200 GRAPHICS DISPLAY [ D ] BLACK GRAY BLUE BLUE GREEN GREEN CYAN CYAN MAGENTA MAGENTA BROWN YELLOW WHITE WHITE Press [Enter] KEY Press ENTER to display 64 gradations of red, green, blue and white on the screen 320*200 GRAPHICS DISPLAY [ 13 ]...
Page 107 Test Program for Field. Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolution to display three windows, each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed. 640 * 200 GRAPHICS DISPLAY : [ 6 ] EVEN...
Page 108 Test Program for Field. Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolution to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Page 109 Test Program for Field. 640*480 GRAPHICS DISPLAY [12 ] BLACK DARK GRAY BLUE LIGHT BLUE GREEN LIGHT GREEN CYAN LIGHT CYAN LIGHT MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Page 110 Test Program for Field. Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 000000000000000000000000000000000000000000000000000000000000000 To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Page 111 Test Program for Field. Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH To exit this subtest and return to the Display Test menu:...
Page 112 Test Program for Field. Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Page 113 Test Program for Field. Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Page 114 Test Program for Field. NOTE: The following screen does not display correctly. It will be amended in the next version. Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [Enter] Key Press Enter to display VRAM mapping test using the all dots Mode.
Page 115 Test Program for Field. Press [Enter] Key To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
Page 116 Test Program for Field. Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display. Black Green Blue Gray Green Blue Gradation Gradation Gradation White Green Blue Gradation Gradation Gradation...
Page 117: Floppy Disk Test
Test Program for Field. Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test select 05 from the Diagnostic Test Menu, press Enter and follow the directions on the screen.
Page 118 Test Program for Field. Subtest 04 Write Specified Address NOTE: The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicates the head, and the last two digits indicate the sector. This subtest allows you to verify the errors from Subtest 02. It writes specified data to a specified track and head.
Page 119: Hard Disk Test
Test Program for Field. Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive. Move the highlight bar to the subtest you want to execute and press Enter.
Page 120 Test Program for Field. Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, then reads the data while moving from cylinder to cylinder.
Page 121 Test Program for Field. Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD. The following message displays on the screen to enter the test data. TEST DATA ????(=37b3H) Subtest 08 W-R-C Specified Address This subtest writes specified data to a specified sector count, then reads and compares the result.
Page 122: Real Time Clock Test
Test Program for Field. 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions.
Page 123 Test Program for Field. Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14 address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION: When this subtest is executed, the current date and time are reset.
Page 124: Cache Memory Test
Test Program for Field. 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cache Memory Test contains eight subtests that test the computer's cache memory. Move the highlight bar to the subtest you want to execute and press Enter.
Page 125 Test Program for Field. Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes reads the new data and compares the result with the original data. The original cache memory content is then restored to the cache memory.
Page 126: High Resolution Display Test
Test Program for Field. 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The High Resolution Display Test contains six subtests that test the computer's high resolution video display. Move the highlight bar to the subtest you want to execute and press Enter.
Page 127 Test Program for Field. Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. [ 640*480 256 ] Press [ Enter ]key 256 letter types...
Page 128 Test Program for Field. Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below. Press [ Enter ] key 800*600 256 256 letter types...
Page 129 Test Program for Field. Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. [ 1024*768 256 ] Press [ Enter ] key 256 letter types...
Page 130 Test Program for Field. Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH...
Page 131 Test Program for Field. Subtest 06 Focus Test ( “E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame. To exit this subtest and return to the High Resolution Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Page 132: Multimedia Test
Move the highlight bar to the subtest you want to execute and press Enter. NOTE: Use the Toshiba Backup CD-ROM for Subtests 01, 02, and 03. Because CDROM driver issue , the Multimedia function can’t test , this is limitation .
Page 133: Memory2 Test
Test Program for Field. 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing.
Page 134 Test Program for Field. Tee test method is the same as Subtest2. However, the data to be used differs. 7FFF7FFF7FFF7FFF8000800080008000 BFFFBFFFBFFFBFFF4000400040004000 DFFFDFFFDFFFDFFF2000200020002000 FFFBFFFBFFFBFFFB0004000400040004 FFFDFFFDFFFDFFFD0002000200020002 FFFEFFFEFFFEFFFE0001000100010001 80008000800080007FFF7FFF7FFF7FFF 4000400040004000BFFFBFFFBFFFBFFF 0004000400040004FFFBFFFBFFFBFFFB 0002000200020002FFFDFFFDFFFDFFFD 0001000100010001FFFEFFFEFFFEFFFE Satellite T110D and Satellite Pro T110D Tests and Diagnostics Manual...
Page 135: Error Codes And Error Status Names
Test Program for Field. 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests. Table 3-2 Error codes and error status names (1/2) Device Name Error Code Error Status Name (Common) Data Compare Error Memory...
Page 136 Test Program for Field. Table 3-2 Error codes and error status names (2/2) Device Name Error Code Error Status Name Undefined Error Write Fault Status Error No Sense Error Other Error Cache Memory Protect Mode Error Caching Error Other Error Multimedia Write Error Invalid Drive...
Page 137: Running Test
Test Program for Field. 3.16 Running Test NOTES: 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated during the Floppy Disk Test.
Page 138: Dmi Infoemation
2. Region Code 3.17.2 Write DMI Information The Write DMI Information program contains the following information for the computer : 1. Manufacture Name ( TOSHIBA ) 2. Product Name ( Satellite XXXXXX ) 3. Part Number ( PSP50X-XXXXXX ) 4. Serial Number ( 12345678W ) 5.
Page 139 Note : Please Check New DMI Information After System Restart !! V3.2 1. **** Manufacture Name ( TOSHIBA ) - (32) 2. **** Product Name ( Satellite XXXXXX ) - (32) 3. **** Part Number ( PSP50X-XXXXXX ) - (26) 4.
Page 140 6. Model Select : [1]Dyn–Jpn : BIOS Logo is “dynabook” , CMOS Language is Japanese . [2]Tos-Jpn : BIOS Logo is “Toshiba” , CMOS Language is Japanese . [3]Tos-Eng : BIOS Logo is “Toshiba” , CMOS Language is English .
Page 141: Log Utilities
Test Program for Field. 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log : 500 times). This function can store data on a floppy disk. If the power switch is turned off, the error information will be lost. Error information is displayed in the following order: 1.
Page 142 Test Program for Field. 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostics Menu. The 4 key erases all error log information in RAM.
Page 143: System Configuration
Test Program for Field. 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * - BIOS VER = VX.XX KBC VER = XXXX * - MAC ADDRESS : XXXXXXXXXXXX * - 0 ASYNC ADAPTER * - 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.:XXXXXXXX...
Page 144: Function Description
Test Program for Field. 3.20 OPTION 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test. KEY OPERATION ...
Page 145 Test Program for Field. 1. Enter a number or 0 for Loop Count and press Enter. Select a number from 1 to 65535 to define the number of times the Running Test executes. Select 0 to run the test continuously until halted by the user. 2.
Page 146: Common Tests And Operation
Test Program for Field. 3.21 Common Tests and Operation 3.21.1 How to operate a window To input parameters, or open a window use the following keys. : to move a highlight bar [Enter] key : to select an item at the highlight bar [Esc] key : to close the current window and go back to the previous window...
Page 147 Test Program for Field. Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test.
Page 148: Test Stop Display
Test Program for Field. 3.21.4 Test Stop Display If an error occurs during a Subtest and YES is selected for Error Stop, the following message displays: [HALT OPERATION] 1. Test end 2. Continue 3. Retry * Select 1, 2, or 3 The three selections have the following functions: 1: Terminates the test program and exits to the subtest menu.
Page 149: Replacement Procedures
Chapter 4 Replacement Procedures Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 150 Chapter 4 Replacement Procedures Chapter 4 Contents Overview........................1 Safety Precautions ....................2 Before You Begin ....................3 Disassembly Procedure................... 4 Assembly Procedure ....................5 Tools and Equipment ....................5 Screw Tightening Torque ..................6 Screw Notation......................7 Battery pack ........................8 HDD..........................
Page 151 Chapter 4 Replacement Procedures Figures Figure 4-2-1 Remove the battery pack................. 9 Figure 4-2-2 Install the battery pack.................. 10 Figure 4-3-1 Turn the computer upside down ..............11 Figure 4-3-2 Remove HDD assembly................12 Figure 4-3-3 Remove HDD ....................13 Figure 4-4-1 Remove memory slot cover ................
Page 152 Chapter 4 Replacement Procedures Figure 4-10-2 Loose the screws................... 36 Figure 4-10-3 Remove the touchpad and touchpad board ........... 36 Figure 4-11-1 Positions of I/O boards ................. 38 Figure 4-11-2 Remove the screws from I/O boards............. 39 Figure 4-12-1 Remove the system board ................40 Figure 4-12-2 Remove the RTC battery-step_1..............
Page 153: Overview
Chapter 4 Replacement Procedures Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed.
Page 154: Safety Precautions
DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba. Other batteries may have different specifications that are incompatible with the computer and may result in fire or explosion.
Page 155: Before You Begin
Chapter 4 Replacement Procedures Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2 Battery Pack”. 1.
Page 156: Disassembly Procedure
Chapter 4 Replacement Procedures Disassembly Procedure Three main types of cable connector are used.  Pressure plate connector  Spring connector  Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cable out from the connector.
Page 157: Assembly Procedure
Chapter 4 Replacement Procedures Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points when assembling the computer. ...
Page 158: Screw Tightening Torque
Chapter 4 Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION: Over-tightening may damage screws or parts. Under-tightening may allow screws to loosen (and possibly fall out) causing a short circuit or other damage. NOTE: To tighten screws quickly and accurately, an electric screwdriver is recommended.
Page 159: Screw Notation
Chapter 4 Replacement Procedures Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types and lengths are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head screw S: Super thin head screw...
Page 160: Battery Pack
Chapter 4 Replacement Procedures Battery pack Removing the battery pack The following describes the procedure for removing the battery pack (See Figure 4-2-1). CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack.
Page 161 Dispose always the used battery pack in accordance with the laws and ordinances of your local authority. Use only the batteries approved by Toshiba. NOTE: Check visually the battery terminals and clean off any dirt with a dry cloth.
Page 162 Chapter 4 Replacement Procedures 3. Attach the battery cover to the battery pack. 4. Insert the battery pack 5. Ensure the battery release latch (2) is moved into its locked position Figure 4-2-2 Install the battery pack Satellite T110D / Satellite Pro T110D / PORTEGE T110DMaintenance Manual (960-Q08)
Page 163: Hdd
Chapter 4 Replacement Procedures Removing a HDD-H9.5mm The following describes the procedure for removing the HDD (See Figure 4-3-1 to 4-3-3). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 1.
Page 164 Chapter 4 Replacement Procedures CAUTION: When a HDD is installed, they are installed in the position as the following figure. Screw M2×4 4pcs PULL TAB Figure 4-3-2 Remove HDD assembly Satellite T110D / Satellite Pro T110D / PORTEGE T110DMaintenance Manual (960-Q08)
Page 165 Chapter 4 Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder.  M3.03.5F FLAT BIND screw M3×3.5 Figure 4-3-3 Remove HDD Installing HDD-H9.5mm The following describes the procedure for installing the main HDD. 1.
Page 166: Memory Module
Chapter 4 Replacement Procedures Memory Module CAUTION: The power of the computer must be turned off when you remove a memory module. Remove a memory module with the power on risks damaging the module or the computer itself. Do not touch memory module terminals. Any dirt on the terminals may cause memory access problems.
Page 167 Chapter 4 Replacement Procedures Figure 4-4-1 Remove memory slot cover Figure 4-4-2 Remove a memory module Satellite T110D / Satellite Pro T110D / PORTEGE T110DMaintenance Manual (960-Q08)
Page 168 Chapter 4 Replacement Procedures Installing a memory module To install a memory module, confirm that the computer is in boot mode. Then perform the following procedure (See Figure 4-4-3). 1. Insert a memory module into the connector of the computer slantwise (terminal side first) and press it to connect firmly.
Page 169: Keyboard
Chapter 4 Replacement Procedures Keyboard Removing the keyboard The following describes the procedure for removing the keyboard (See Figure 4-5-1 to 4-5-2). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do not touch the keycap. 1.
Page 170 Chapter 4 Replacement Procedures Figure 4-5-1 Remove 2 screws for KB Holder Figure 4-5-2 Remove Keyboard Holder and Keyboard Satellite T110D / Satellite Pro T110D / PORTEGE T110DMaintenance Manual (960-Q08)
Page 171 Chapter 4 Replacement Procedures Installing the keyboard The following describes the procedure for installing the keyboard. 1. Connect the keyboard flexible cable to the connector on the system board. 2. Slide and set the keyboard. 3. Install the K/B holder by pressing it from the topside. 4.
Page 172 Chapter 4 Replacement Procedures Wireless LAN card and Bluetooth Module Removing a Wireless LAN card The following describes the procedure for removing a Wireless LAN card (See Figure 4-6-1). Disconnect the wireless LAN antenna cable from the connectors on a wireless LAN card.
Page 173 Chapter 4 Replacement Procedures Removing a Bluetooth module The following describes the procedure for removing a Bluetooth module (See Figure 4-6-2). Disconnect the Bluetooth cable f from the connector on the system board. Remove the Bluetooth module from the hook on the Base Assembly. Figure 4-6-2 Remove a Bluetooth Module Installing a Bluetooth module The following describes the procedure for installing a Bluetooth module.
Page 174: Module Card
Chapter 4 Replacement Procedures 3G module card Removing 3G module card The following describes the procedure for removing a 3G module card (See Figure 4-7-1). Disconnect the 3G antenna cable from the connectors on a 3G module card. Open the left and right latches holding a 3G module card and remove a 3G module card from the connector on the system board.
Page 175: Display Assembly
Chapter 4 Replacement Procedures 4.8 Display Assembly Removing the display assembly The following describes the procedure for removing the display assembly (See Figure 4-8-1 to 4-8-7). 1. Close the display and turn the computer upside down. 2. Remove the battery pack (See Figure 4-2-1) 3.
Page 176 Chapter 4 Replacement Procedures Figure 4-8-2 Remove the memory slot cover 4. Remove the screws from the bottom side. Figure 4-8-3 Remove the screws (from bottom side) 5. Disassemble KB Holder and KB (See Figure 4-5-1 to Figure 4-5-2) 6. Remove the screws from the top side and remove the cover. Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 177 Chapter 4 Replacement Procedures Figure 4-8-4 Remove the screws (from top side) 7. Disconnect the touch pad FFC/LAN FFC/Power FFC from the connector on the system board. Figure 4-8-5 Disconnect the touch pad FFC/LAN FFC/Power FFC 8. Disassembly TOP Cover Assembly. Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 178 Chapter 4 Replacement Procedures 9. Disconnect the LAN FFC on LAN board and remove the LAN FFC 10. Remove the screws from the LAN board and remove the LAN board. Figure 4-8-6 Remove the LAN board 11. Disconnect the wireless LAN antenna cable and 3G antenna cable from the connectors on the cards.
Page 179 Chapter 4 Replacement Procedures 14. Opening the display to 120degree, keeping display side by hand and remove the hinge screw ‧ M2.0 4F FLAT BIND screw Figure 4-8-8 Remove the hinge screws 15. Remove the display assembly with two hands holding from the base assembly. Figure 4-8-9 Remove the display assembly Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 180 Chapter 4 Replacement Procedures Installing the display assembly The following describes the procedure for installing the display assembly. 1. Inserting the pole of hinge to the hole of hinge assembly, set the display assembly with hands on the base assembly. 2.
Page 181 Chapter 4 Replacement Procedures Figure 4-8-11 Connect LCD harness to the system board 4. Put the DC-IN connector to the base assembly. 5. Arrange the wireless antenna cables and 3G antenna cables along the guide Figure 4-8-12 Arrange and connect Wireless LAN cable and 3G Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 182 Chapter 4 Replacement Procedures 6. Install the LAN board and secure the screws on the LAN board. Figure 4-8-13 Install the LAN board 7. Connect the LAN FFC to the connector on the LAN board. 8. Arrange the Wireless LAN antenna and 3G antenna along the guide and contact with the connector with hands.
Page 183: Top Cover Assembly
Chapter 4 Replacement Procedures 4.9 Top Cover Assembly Removing the top cover assembly The following describes the procedure for removing the top cover assembly (See Figure 4-9- 1 to 4-9-4). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer.
Page 184 Chapter 4 Replacement Procedures 4. Remove the following screws securing the top cover assembly from the front of computer. Pull up and remove the top cover assembly from the base assembly. Figure 4-9-2 Remove the screws (front) and top cover assembly 5.
Page 185 Chapter 4 Replacement Procedures 6. Disconnect the Power FFC from the connector on the Power board. Remove the following screws securing the Power Board from the bottom of Top Cover Assembly. Figure 4-9-4 Remove the screws and Power FFC from the Power Board Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 186 Chapter 4 Replacement Procedures Installing the top cover assembly The following describes the procedure for installing the top cover assembly. 1. Connect the Power FFC to the connector on the power board. 2. Secure the power board with the following screws. ...
Page 187: Touch Pad
Chapter 4 Replacement Procedures 4.10 Touch Pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-10-1 to 4- 10-3). 1. Disconnect the touch pad board FFC, touch pad FFC from the connector on the touch pad board.
Page 188 Chapter 4 Replacement Procedures Figure 4-10-2 Remove the screws Figure 4-10-3 Remove the touchpad and touchpad board Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 189 Chapter 4 Replacement Procedures Installing the touch pad The following describes the procedure for installing the touch pad. 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE: Do not reuse the touch pad so that it can not be used after peeling off from the computer.
Page 190: I/O Boards
Chapter 4 Replacement Procedures 4.11 I/O Boards Removing I/O Boards The following describes for removing the I/O boards (See Figure 4-11-1 and Figure 4-11-2). 1. Disconnect HDMI FFC, Audio FFC and LAN FFC from I/O boards’ connectors. 2. Remove below screws and then incline pull out I/O Boards (CRT board, HDMI board, Audio board and LAN board) 3.
Page 191 Chapter 4 Replacement Procedures Figure 4-11-2 Remove the screws from I/O boards Installing I/O Boards The following describes for installing I/O boards. 1. Fix the below screws then incline insert in I/O Boards(CRT board, HDMI board, Audio board and LAN board) ...
Page 192: System Board
Chapter 4 Replacement Procedures 4.12 System board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. if replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configuration”. Removing the system board The following describes the procedure for removing the system board (See Figure 4-12-1).
Page 193 Chapter 4 Replacement Procedures Installing the system board The following describes the procedure for installing the system board. 1. Connect the RGB cable and DC-IN cable to the connector on the system board. 2. Secure the system board with the following screws. ...
Page 194 Chapter 4 Replacement Procedures Removing RTC battery The following describes the procedure for removing the RTC battery unit (See Figure 4-12-2 to 4-12-3). 1. Pull the away the socket of RTC battery and use a clamp to hold RTC battery tightly. 2.
Page 195 Chapter 4 Replacement Procedures Figure 4-12-3 Remove the RTC battery-step_2 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 196 Chapter 4 Replacement Procedures Installing RTC battery The following describes the procedure for installing the RTC battery unit (See Figure 4-12-4). 1. Press the force vertically then lock the RTC battery tightly. Figure 4-12-4 Install the RTC battery Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 197: Cpu Heat Sink
Chapter 4 Replacement Procedures 4.13 CPU heat sink Removing the CPU heat sink The following describes the procedure for removing the CPU heat sink (See Figure 4-13-1). 1. Disconnect the Heat sink cable from the connector on the system board 2.
Page 198 Chapter 4 Replacement Procedures Installing the CPU heat sink The following describes the procedure for installing the CPU heat sink Secure the following screws securing the heat sink holder along 1 to 3.  M2.03.0F FLAT BIND screw Connect the Heat sink cable from the connector on the system board Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 199: Lcd Unit
Chapter 4 Replacement Procedures 4.14 LCD unit Removing the LCD unit The following describes the procedure for removing the LCD unit (See Figure 4-14-1 to 4- 14-4). 1. Remove Screw MYLAR cover x4 2. Remove the following screws securing the display mask ...
Page 200 Chapter 4 Replacement Procedures Figure 4-14-2 Remove screws securing the LCD 5. Remove the LCD unit, the hinge and the LCD Harness from the bottom side Figure 4-14-3 Remove the LCD Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 201 Chapter 4 Replacement Procedures 6. With the bottom edge of the LCD unit on the display cover, lift only the top edge of the LCD unit. After peeling off the MYLAR tape, disconnect the LCD harness from the connector on the back of the LCD. Figure 4-14-4 Remove the harness 7.
Page 202 Chapter 4 Replacement Procedures Installing the LCD unit The following describes the procedure for installing the LCD unit. Install the LCD supports (LCD unit side) and hinge to the LCD and secure them with the following screws.  M22.5F FLAT BIND screw 1.
Page 203: Web Camera Module
Chapter 4 Replacement Procedures 4.15 Web Camera module Removing Web Camera module The following describes the procedure for removing the Web Camera module. (See Figure 4-15-1 to 4-15-3). Remove EMI tape on the web camera module. Peel off the glue of Web Camera module. Peel off the glue of Web Camera module.
Page 204 Chapter 4 Replacement Procedures Figure 4-15-3 Peel off the glue of Web Camera module Installing Web Camera module The following describes the procedure for installing the Web Camera module. 1. Connect the connector of Web Camera module. 2. Pull in the glue of Web Camera Module. 3.
Page 205: Application For Thermal Grease On Cpu And North Bridge
Chapter 4 Replacement Procedures 4.16 Application for Thermal grease on CPU and North Bridge (See Figure 4-16-1) For thermal grease on North Bridge and CPU Figure 4-16-1 Intel &AMD Thermal grease on North Bridge and CPU A000018310 THERMAL GREASE FCR-AS A000063980 THERMAL GREASE 7762 Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 206 Chapter 4 Replacement Procedures II. Use grease on North Bridge and CPU 0.15cc for one repair. Figure 4-16-2 Apply silicon grease for North Bridge and CPU Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 207: Speaker Box
Chapter 4 Replacement Procedures 4.17 Speaker Box Removing Speaker Box The following describes the procedure for removing Speaker Box. (See Figure 4-17-1 to 4- 17-3). Remove the following screws securing Speaker Box.  M2.03F FLAT BIND screw Remove the Speaker Box. Figure 4-17-1 Remove the securing screws at left side.
Page 208 Chapter 4 Replacement Procedures Figure 4-17-3 Remove the Speaker Box. Installing Speaker Box The following describes the procedure for installing Speaker Box. Install the Speaker Box. Secure Speaker Box of following screws.  M2.03F FLAT BIND screw Satellite T110D / Satellite Pro T110D / PORTEGE T110D Maintenance Manual (960-Q08)
Page 209: Hdd Cable
Chapter 4 Replacement Procedures 4.18 HDD Cable Removing HDD cable The following describes the procedure for removing HDD cable. (See Figure 4-18-1). 1. Remove HDD door and RAM door. 2. Pull out HDD cable from the direction as below picture showed. Figure 4-18-1 Remove the HDD cable.
Page 210 Appendices Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 211: Appendix A Handling The Lcd Module
Appendix Contents Appendix A Handling the LCD Module................1 Appendix B Board Layout....................1 System Board ....................1 Touch Pad Board....................4 CRT Board ......................6 Power Board...................... 8 SIM Card Board....................10 HDMI Board ....................12 ADO_USB Board ................... 14 LAN Board......................
Page 212 AppendixD Display Codes....................1 Display Codes ....................1 Appendix E Keyboard Layout .................... 1 United States (US) Keyboard................1 Thai (TI) Keyboard................... 1 Korean (KO) Keyboard ..................2 United Kingdom (UK) Keyboard..............2 US International (UI) Keyboard ............... 3 Hebrew (HB) Keyboard ................... 3 Danish (DM) Keyboard..................
Page 213 E.29 Frence_Canadian(Acnor) Keyboard..............15 E.30 Japanese (JP) Keyboard................... 15 E.31 Bulgarian Keyboard..................16 E.32 Taiwan(TW) Keyboard ................... 16 Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 214: Appendix F Wiring Diagrams
Appendix F Wiring Diagrams..................F-1 RGB Monitor ID Wraparound Connector ............ F-1 LAN Loopbak Connector ................F-1 Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 215: Appendix A Handling The Lcd Module
Handling the LCD Module Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.
Page 216 Handling the LCD Module 3. If the panel’s surface gets fingerprint or dust, put on gloves and wipe it with static electricity cloth. If it is still dirty, drop some cleaning alcohol on the surface and wipe it again. If the surface is much more fingerprint or dust, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface.
Page 217 Handling the LCD Module 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite T110D / Satellite Pro T110D /PORTEGE T110D Maintenance Manual (960-Q08)
Page 218 Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9.
Page 219 Handling the LCD Module 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite T110D / Satellite Pro T110D /PORTEGE T110D Maintenance Manual (960-Q08)
Page 220: Appendix B Board Layout
Board Layout Appendix B Appendix B Board Layout B.1 System Board Figure B-1-1 System board layout (front) Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 221 Board Layout Figure B-1-2 System board layout (Back) Location Function (01) LVDS CONN (02) POWER BOARD CONN (03) KB CONN (04) LAN CONN (05) SATA HDD CONN Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 222 Board Layout (06) TP CONN (07) ODD CONN (08) 3G CONN (09) AUDIO Board CONN (10) CN10 RTC CONN (11) CN11 HDMI Board CONN (12) CN12 BT CONN (13) PCN1 AC-IN CONN (14) CN14 BATTERY CONN (15) CN15 FAN CONN (16) CN16 CRT CONN...
Page 223: Touch Pad Board
Board Layout B.2 Touch Pad Board <Front layout> Figure B-2-1 Touch Pad board layout (Front) Location Function (01) Mouse Button Left key (02) Mouse Button Right key (03) HALL Sensor Table B-2-2 Touch Pad board connectors <Back layout> Figure B-2-3 Touch Pad board layout (Back) Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 224 Board Layout Location Function (01) LED1 AC-IN LED (02) LED2 POWER LED (03) LED3 BATT LED (04) LED4 HDD LED (05) LED5 Bridge Media LED (06) LED6 W-LAN LED (07) LED7 WiMAX/3G LED (08) TP Board to TP Module CONN (09) TP Board to M/B CONN Table B-2-4 Touch Pad board connectors...
Page 225: Crt Board
Board Layout B.3 CRT Board <Front layout> Figure B-3-1 Finger Print Board layout (Front) Location Function CRT ESD protection, level-shifting ,sync impedance (01) matching IC (02) CRT CONN Table B-3-2 CRT Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 226 Board Layout <Back layout> Figure B-3-3 CRT Board layout (Back) Location Function (01) CRT to M/B CONN Table B-3-4 Finger Print Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 227: Power Board
Board Layout B.4 Power Board <Front layout> Figure B-4-1 Power Board layout (Front) Location Function (01) Power SW (02) LED1 Power LED Table B-4-2 Power Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 228 Board Layout <Back layout> Figure B-4-3 Power Board layout (Back) Location Function (01) Power/B to M/B CONN Table B-4-4 Power Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 229 Board Layout B.5 SIM (3G) Board <Front layout> Figure B-5-1 SIM (3G) Board layout (Front) Location Function (01) SIM(3G)/B to M/B CONN Table B-5-2 SIM (3G) Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 230 Board Layout <Back layout> Figure B-5-3 SIM (3G) Board layout (Back) Location Function (01) JSIM1 SIM Card CONN Table B-5-4 SIM (3G) Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 231: Hdmi Board
Board Layout B.6 HDMI Board <Front layout> Figure B-6-1 HDMI Board layout (Front) Location Function (01) HDMI CONN (02) HDMI/B to M/B CONN (03) USB CONN (04) 5 IN 1 Card Reader CONN Table B-6-2 HDMI Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 232 Board Layout <Back layout> Figure B-6-3 HDMI Board layout (Front) Location Function (01) HDMI LEVEL SHIFT IC (02) Card Reader IC Table B-6-4 HDMI Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 233 Board Layout B.7 ADO_USB Board <Front layout> Figure B-7-1 ADO_USB Board layout (Front) Location Function (01) USB CONN (02) USB CONN (03) Inner Speaker CONN (04) Earphone CONN (05) ADO_USB Board to M/B CONN (06) External MIC CONN Table B-7-2 ADO_USB Board connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 234 Board Layout <Back layout> Figure B-7-3 ADO_USB Board layout (Back) Location Function (01) Codec IC Table B-7-4 ADO_USB Board IC Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 235: Lan Board
Board Layout B.8 LAN Board <Front layout> Figure B-8-1 LAN Board layout (Front) Location Function (01) RJ45 CONN (02) LAN Board to M/B CONN (03) LAN Transformer Table B-8-1 LAN Board IC and connectors Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 236 Board Layout <Back layout> Figure B-8-2 LAN Board layout (Back) Satellite T110D / Satellite ProT110D /PROTEGE T110D Maintenance Manual (960-Q08)
Page 237: Appendix C Pin Assignment
Pin Assignment Appendix C Pin Assignment CN1 LCD Panel Connectors PIN No. Signal name PIN No. Signal name LCDVCC LCDVCC CDD_POWER MIC_GND IN_MIC_R USBP10-_LCD USBP10+_LCD LCD_DDCCLK LCD_DDCDAT INT_TXLCLKOUT- INT_TXLCLKOUT+ INT_TXOUT2- INT_TXOUT2+ INT_TXOUT1- INT_TXOUT1+ INT_TXOUT0- INT_TXOUT0+ LVDS_VADJ DISPON Power Board Connector PIN No.
Page 238: Cn3 Keyboard Connectors
Pin Assignment CN3 Keyboard Connectors PIN No. Signal name PIN No. Signal name K_LED_P MY16 MX17 K_LED_P MY14 MY13 MY10 MY11 MY12 MY15 K_LED_P CAPSLED FN_F10 NUMLED LAN Connector PIN No. Signal name PIN No. Signal name AVDD_CEN TX1P TX1N TX0P TX0N Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 239: Cn5 Sata Hdd Connectors
Pin Assignment CN5 SATA HDD Connectors PIN No. Signal name PIN No. Signal name SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 240: Cn6 Touchpad Connectors
Pin Assignment CN6 Touchpad Connectors PIN No. Signal name PIN No. Signal name LID591# TPCLK TPDATA MMC_LED# 3G_WIMAX_LED# --- RF_LED SATA_LED#_C BAT_SAT1 BAT_SAT0 SUSLED_EC PWERLED# ACIN +3VPCU NUMLED FN_F10 CN9 Audio USB Board Connectors PIN No. Signal name PIN No. Signal name ACZ_SDIN0 ACZ_SDOUT_AUDIO I/O...
Page 241: Cn10 Rtc Battery Connectors
Pin Assignment AMP_MUTE# SPKR USBOC#0 USBP1+ USBP1- USBP0+ USBP0- USB_EN#0_1 +5VPCU +5VPCU +5VPCU +5VPCU +5VPCU CN10 RTC Battery Connectors PIN No. Signal name PIN No. Signal name TERM12 CN11 HDMI Connectors PIN No. Signal name PIN No. Signal name USBP11- USBP11+ PLTRST# +5VPCU...
Page 242: Cn12 Bluetooth Connectors
Pin Assignment MMC_LED# BUSBP3- BUSBP3+ USB_SLEEP_OC# USB_SLEEP_EN# BOARD_ID2 HDMI_CON_HP HDMI_CON_DDCDATA I/O HDMI_CON_DDCCLK O HDMICLKN HDMICLKP HDMITX0N HDMITX0P HDMITX1N HDMITX1P HDMITX2N HDMITX2P C.10 CN12 Bluetooth Connectors PIN No. Signal name PIN No. Signal name USBP9+ USBP9- WCS_CLK BT_RESET WCS_DAT BT_EN C.11 CN14 Battery Connectors PIN No.
Page 243: Cn15 Fan Connectors
Pin Assignment MBAT+ C.12 CN15 FAN Connectors PIN No. Signal name PIN No. Signal name TH_FAN_POWER FANSIG C.13 CN16 CRT Connector PIN No. Signal name PIN No. Signal name DDCDAT VSYNC DDCCLK HSYNC RED_L GREEN_L BLUE_L C.14 CN19 DDR Connectors PI N No.
Page 244 Pin Assignment MEM_MA_DQS0_N MEM_MA_DQS0_P MEM_MA_DATA6 MEM_MA_DATA7 MEM_MA_DATA2 M_B_DQ2 M_B_DQ13 M_B_DQ12 M_B_DQ9 M_B_DQ8 M_B_DQS#1 M_B_DM1 M_B_DQS1 DDR3_DRAMRST# M_B_DQ11 M_B_DQ14 M_B_DQ10 M_B_DQ15 M_B_DQ16 M_B_DQ20 M_B_DQ21 M_B_DQ17 M_B_DQS#2 M_B_DM2 M_B_DQS2 M_B_DQ18 M_B_DQ22 M_B_DQ23 M_B_DQ19 M_B_DQ28 M_B_DQ24 M_B_DQ25 M_B_DQ29 Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 245 Pin Assignment M_B_DQS#3 M_B_DM3 M_B_DQS3 M_B_DQ26 M_B_DQ30 M_B_DQ27 M_B_DQ31 M_CKE2 M_CKE3 +1.5VSUS +1.5VSUS M_B_BS#2 M_B_A14 +1.5VSUS +1.5VSUS M_B_A12 M_B_A11 M_B_A9 M_B_A7 +1.5VSUS +1.5VSUS M_B_A8 M_B_A6 M_B_A5 M_B_A4 +1.5VSUS +1.5VSUS M_B_A3 M_B_A2 M_B_A1 M_B_A0 +1.5VSUS +1.5VSUS M_CLK_DDR2 M_CLK_DDR3 M_CLK_DDR#2 M_CLK_DDR#3 +1.5VSUS +1.5VSUS ---- M_B_A13...
Page 246 Pin Assignment +1.5VSUS +1.5VSUS M_B_WE# M_CS#2 M_B_CAS# M_ODT2 +1.5VSUS +1.5VSUS M_B_A13 M_ODT3 M_CS#3 +1.5VSUS +1.5VSUS SMDDR_VREF_DI M_B_DQ32 M_B_DQ36 M_B_DQ37 M_B_DQ33 M_B_DQS#4 M_B_DM4 M_B_DQS4 M_B_DQ38 M_B_DQ34 M_B_DQ39 M_B_DQ35 M_B_DQ44 M_B_DQ41 M_B_DQ45 M_B_DQ40 M_B_DQS#5 M_B_DM5 M_B_DQS5 M_B_DQ43 M_B_DQ46 M_B_DQ47 M_B_DQ42 Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 247: Cn20 Ddr Connectors
Pin Assignment M_B_DQ53 M_B_DQ50 M_B_DQ52 M_B_DQ48 M_B_DQS#6 M_B_DM6 M_B_DQS6 M_B_DQ51 M_B_DQ51 M_B_DQ55 M_B_DQ49 M_B_DQ59 M_B_DQ56 M_B_DQ61 M_B_DQ57 M_B_DQS#7 M_B_DM7 M_B_DQS7 M_B_DQ60 M_B_DQ58 M_B_DQ62 M_B_DQ63 PM_EXTTS#1 CGDAT_SMB CGCLK_SMB +SMDDR_VTERM +SMDDR_VTERM C.15 CN20 DDR Connectors PI N No. Signal name PIN No. Signal name SMDDR_VREF_DIMM Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 248 Pin Assignment M_A_DQ4 M_A_DQ0 M_A_DQ7 M_A_DQ5 M_A_DQS#0 M_A_DM0 M_A_DQS0 M_A_DQ3 M_A_DQ1 M_A_DQ6 M_A_DQ2 M_A_DQ10 M_A_DQ15 M_A_DQ8 M_A_DQ13 M_A_DQS#1 M_A_DM1 M_A_DQS1 DDR3_DRAMRS M_A_DQ9 M_A_DQ14 M_A_DQ10 M_A_DQ11 M_A_DQ23 M_A_DQ17 M_A_DQ18 M_A_DQ21 M_A_DQS#2 M_A_DM2 M_A_DQS2 M_A_DQ20 M_A_DQ22 M_A_DQ19 Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 249 Pin Assignment M_A_DQ16 M_A_DQ26 M_A_DQ24 M_A_DQ29 M_A_DQ31 M_A_DQS#3 M_A_DM3 M_A_DQS3 M_A_DQ28 M_A_DQ27 M_A_DQ25 M_A_DQ30 M_CKE2 M_CKE3 +1.5VSUS +1.5VSUS M_A_BS#2 M_A_A14 +1.5VSUS +1.5VSUS M_A_A12 M_A_A11 M_A_A9 M_A_A7 +1.5VSUS +1.5VSUS M_A_A8 M_A_A6 M_A_A5 M_A_A4 +1.5VSUS +1.5VSUS M_A_A3 M_A_A2 M_A_A1 M_A_A0 +1.5VSUS +1.5VSUS M_CLK_DDR0 M_CLK_DDR1 Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 250 Pin Assignment M_CLK_DDR#0 M_CLK_DDR#1 +1.5VSUS +1.5VSUS ---- M_A_A13 M_A_BS#1 M_A_BS#0 M_A_RAS# +1.5VSUS +1.5VSUS M_A_WE# M_CS#0 M_A_CAS# M_ODT0 +1.5VSUS +1.5VSUS M_A_A13 M_ODT1 M_CS#1 +1.5VSUS +1.5VSUS SMDDR_VREF_ DIMM M_A_DQ32 M_A_DQ34 M_A_DQ37 M_A_DQ39 M_A_DQS#4 M_A_DM4 M_A_DQS4 M_A_DQ33 M_A_DQ36 M_A_DQ38 M_A_DQ35 M_A_DQ47 M_A_DQ41 M_A_DQ45 M_A_DQ40 M_A_DQS#5 Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 251 Pin Assignment M_A_DM5 M_A_DQS5 M_A_DQ42 M_A_DQ44 M_A_DQ43 M_A_DQ46 M_A_DQ49 M_A_DQ50 M_A_DQ55 M_A_DQ53 M_A_DQS#6 M_A_DM6 M_A_DQS6 M_A_DQ48 M_A_DQ51 M_A_DQ55 M_A_DQ54 M_A_DQ57 M_A_DQ63 M_A_DQ60 M_A_DQ56 M_A_DQS#7 M_A_DM7 M_A_DQS7 M_A_DQ59 M_A_DQ62 M_A_DQ61 M_A_DQ58 PM_EXTTS#0 CGDAT_SMB CGCLK_SMB Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 252: Cn23 Wlan Connectors
Pin Assignment +SMDDR_VTERM +SMDDR_VTER C.16 CN23 WLAN Connectors PIN No. Signal name PIN No. Signal name WLAN_WAKE# +3V_WL_VDD WCS_DAT WCS_CLKR +1.5V LAD0_PCIE LAD1_PCIE CLK_PCIE_MINI1# LAD2_PCIE CLK_PCIE_MINI1 LAD3_PCIE LFRAME#_PCIE RF_EN PLTRST# PCIE_RXN2 +3V_WL_VAUX PCIE_RXP2 +1.5V WL_SMCLK PCIE_TXN2 WL_SMDATA PCIE_TXP2 USBP8- USBP8+ +3V_WL_VAUX Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 253 Pin Assignment +3V_WL_VAUX PCLK__DEBUG PLTRST#_DEBUG +1.5V LDRQ#0__DEBUG SERIRQ_DEBUG +3V_WL_VDD Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 254: Appendixd Display Codes
Display Codes Appendix. D Appendix D Display Codes Display Codes Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp Table D-1-1 Scan codes (set 1 and set 2) (1/4) Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 255 Display Codes Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) Table D-1-1 Scan codes (set 1 and set 2) (2/4) Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 256 Display Codes Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl Alt (L) Space ALT (R)  Home   PgUp PgDn   Table D-1-1 Scan codes (set 1 and set 2) (3/4) Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 257 Display Codes Code set 1 Code set 2 Keytop Note Make Break Make Break PrintSc Pause — — — — Table D-1-1 Scan codes (set 1 and set 2) (4/4) Notes: 1. * Scan codes differ by mode. 2. * Scan codes differ by overlay function. 3.
Page 258 Display Codes Code set 1 Code set 2 Make Break Make Break E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 E0 AA E0 53 E0 D3 E0 2A E0 F0...
Page 259 Display Codes Code set 1 Code set 2 Make Break Make Break E0 2A E0 52 E0 D2 E0 AA E0 12 70 E0 F0 E0 F0 12 E0 2A E0 53 E0 D3 E0 AA E0 12 71 E0 F0 E0 F0 12 ...
Page 260 Display Codes Code set 1 Code set 2 Keytop Make Break Make Break (–) Table D-1-5 Scan codes in overlay mode Code set 1 Code set 2 Shift Make Break Make Break Prt Sc Common Ctrl  Shift  Alt  Table D-1-6 No.124 key scan code Satellite T110D / Satellite Pro T110D / PROTÉGÉ...
Page 261 Display Codes Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 Table D-1-7 No.126 key scan code *: This key generates only make codes. Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 262: Appendix E Keyboard Layout
Appendix E Keyboard Layout E.1 United Status (US) Keyboard Figure US keyboard E.2 Thai (TI) Keyboard Figure TI keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 263: Korean (Ko) Keyboard
E.3 Korean (KO) Keyboard Figure KO keyboard United Kingdom (UK) Keyboard Figure UK keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 264: Us International (Ui) Keyboard
E.5 US International (UI) Keyboard Figure UI keyboard E.6 Hebrew (HB) Keyboard Figure HB keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 265: Danish (Dm) Keyboard
E.7 Danish (DM) Keyboard Figure DM keyboard E.8 Swiss (SW) Keyboard Figure SW keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 266: Arabic (Are) Keyboard
E.9 Arabic (ARE) Keyboard Figure ARE keyboard E.10 Czech (CZ) Keyboard Figure CZ keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 267: Russian (Ru) Keyboard
E.11 Russian (RU) Keyboard Figure RU keyboard E.12 Portuguese (PO) Keyboard Figure PO keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 268: Slovakian (Sl) Keyboard
E.13 Slovakian (SL) Keyboard Figure SL keyboard E.14 Italian (IT) Keyboard Figure IT keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 269: French (Fr) Keyboard
E.15 French (FR) Keyboard Figure FR keyboard E.16 German (GR) Keyboard Figure GR keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 270: Greek (Gk) Keyboard
E.17 Greek (GK) Keyboard Figure GK keyboard E.18 French_Canadian (Bilingual) Keyboard Figure F(BI) keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 271: Hungarian (Hg) Keyboard
E.19 Hungarian (HG) Keyboard Figure HG keyboard E.20 Spanish (SP) Keyboard Figure SP keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 272: Turkish (Tr) Keyboard
E.21 Turkish (TR) Keyboard Figure TR keyboard E.22 Turkish F (TF-F) Keyboard Figure TF-F keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 273: Swedish (Sd) Keyboard
E.23 Swedish (SD) Keyboard Figure SD keyboard E.24 Belgian_Flemish (BE) Keyboard Figure BE keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 274: Yugoslavian (Yu) Keyboard
E.25 Yugoslavian (YU) Keyboard Figure YU keyboard E.26 Norwegian (NW) Keyboard Figure NW keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 275: Scandinavian (Nd) Keyboard
E.27 Scandinavian (ND) Keyboard Figure ND keyboard E.28 Romanian(RM) Keyboard Figure RM keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 276: Frence_Canadian(Acnor) Keyboard
E.29 Frence_Canadian(Acnor) Keyboard Figure Acnor keyboard E.30 Japanese (JP) Keyboard Figure JP Keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 277: Bulgarian Keyboard
E.31 Bulgarian Keyboard Figure Keyboard E.32 Taiwan(TW) Keyboard Figure TW Keyboard Satellite T110D / Satellite Pro T110D / PROTÉGÉ T110D Maintenance Manual (960-Q08)
Page 278: Appendix F Wiring Diagrams
Wiring Diagrams Appendix F Appendix F Wiring Diagrams RGB Monitor ID Wraparound connector Figure F-1-1 RGB Monitor ID Wraparound connector (15PIN to 15PIN) LAN Loopback Connector (3) BIDBP (RX+) (1) BIBAP ‘(TX+) (4) BIDBN (RX-) (2) BIDAN (TX-) Figure F-2-1 LAN loopback connector Satellite T110D / Satellite Pro T110D / PROTÉGÉ...

This manual is also suitable for:

Satellite t110dd Portege t110dd

Toshiba Satellite Pro T110DD Maintenance Manual

Table of Contents

Chapter 1 Hardware Overview

Chapter 1 Hardware Overview

Chapter 2 Troubleshooting Procedures

Chapter 2 Troubleshooting Procedures

Chapter 3 Diagnostic Programs

Chapter 3 Diagnostic Programs

Chapter 4 Replacement Procedures

Chapter 4 Replacement Procedures

Appendix

Appendix A Handling the LCD Module

Appendix B Board Layout

Appendix F Wiring Diagrams

Appendix A Handling the LCD Module

Appendix Contents

Appendix B Board Layout

Appendix C Pin Assignment

Appendix E Keyboard Layout

Appendix F Wiring Diagrams

Quick Links

Chapters

Troubleshooting

Related Manuals for Toshiba Satellite Pro T110DD

Summary of Contents for Toshiba Satellite Pro T110DD