Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
Overall Length. . . . . . . . . . . . . . . . . . . . . . 61
Hull Length . . . . . . . . . . . . . . . . . . . . . . . . . 55"
Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5 lb
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mph
Engine . . . . . . . . . . . . . . . . Zenoah G-23 Marine
Propeller . . . . . . . . . . . . . . . . . . . . . Prather 270
Radio System . . . . . . . . . . . . . . . . JR XR3 (FM)
/
"
1
2
3
/
"
4
TM
Advertisement
Table of Contents
Related Manuals for ProBoat Shockwave
Summary of Contents for ProBoat Shockwave
- Page 1 INSTRUCTION MANUAL Overall Length..... . 61 " Hull Length ......55" Beam .
-
Page 2: Table Of Contents
Table of Contents Introduction ..................3 Warning . -
Page 3: Introduction
If you find any damage or there are missing items, immediately notify the place of purchase. WARNING This boat is not a toy! It is a high performance R/C model boat. If operated in a careless or reckless manner, the ShockWave is capa- ble of inflicting serious injury to people and property. -
Page 4: Suggested Field Equipment And Supplies
Suggested Field Equipment and Supplies Although your ShockWave comes fully assembled and ready for action, you will need a few tools to keep it running in top form. We recommend that you have in your field kit the following items:... -
Page 5: Section 1: Building The Boat Stand
Section 1: Building the Boat Stand Parts Needed Tools and Adhesives Needed • Plywood boatstand pieces (4) • CA or epoxy Step 1. There are 4 plywood boatstand pieces. The 2 short ply- Step 3. Secure the interlocking boatstand with medium thick wood pieces are the ends of the boat stand. -
Page 6: Section 2: Installing The Receiver And Transmitter Batteries
Section 2: Installing the Receiver and Transmitter Batteries Step 1. Remove the rear hatch with a 3/32 hex wrench. Step 7. Remove the JR XR3 transmitter from its foam packaging. Step 2. Remove clear plastic cover from the radio box. Step 8. -
Page 7: Section 3: Fuel/Oil Mixture
Section 4: Range Checking the XR3 Radio System It is important before the first run of your ShockWave to range Step 2. Have an assistant remain with the boat to check for check the receiver and transmitter for proper operation and to proper control movement from your transmitter input. -
Page 8: Section 6: Maintenance
Please read and complete the following directions below for lubricating the flex drive and propeller shaft. Step 1. Obtain a small container to hold the many small parts that you will be removing from the ShockWave so they don’t get misplaced. - Page 9 Step 5. Loosen the top 2 bolts on the strut mount with a 9/64 Step 10. Reinstall the lower shaft drive strut into the strut Allen wrench. Loosen and remove the 2 bottom bolts from the mount. Reinstall the 2 lower bolts and loosely tighten. strut mount.
-
Page 10: Section 7: Performance Tips
Trim Tabs: The trim tabs can greatly enhance the performance of Wake Conditions: It is advisable to run your ShockWave in low your ShockWave. To adjust the angle of the trim tabs, use a large to medium wake conditions to avoid having problems with the adjustable wrench to carefully bend the tabs as shown. -
Page 11: Section 8: Replacement Parts
Section 8: Replacement Parts If replacement parts are needed for your ShockWave, you can find these quality parts at your local hobby shop. Part # PRB2001 Right/Left Strut Bracket PRB2002 Strut w/Bushing PRB2003 Rudder Extension PRB2004 Control Arm PRB2005 Nylon Washers (2) PRB2006 Steel Shaft Log (280mm-11.0") - Page 12 © Copyright 2000, Horizon Hobby, Inc. 877-504-0233 www.horizonhobby.com...