Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Brady THT MVPplus
Summary of Contents for Brady THT MVPplus
- Page 1 Bradyprinter MVPplus User and Quick Reference Guide...
-
Page 3: Table Of Contents
This quick start guide provides basic information to install and operate your printer. For more detailed information, refer to the users guide (part number 13163L-12). Label preparation software is available for your printer. Contact your distributor or Brady Corporation at http://www.bradyid.com... -
Page 4: Printer Power
Bradyprinter THT MVPplus Quick Reference Guide Printer Power Printer Power The power supply in the printer automatically detects the applied line voltage and works in the 90 to 265 VAC range. The AC power cord has a three-prong female connector on one end that plugs into the mating connector at the rear of the printer. -
Page 5: Media
Bradyprinter THT MVPplus Quick Reference Guide Media Media The printer can use various types of media (Table Table 1 • Types of Media Media Type How It Looks Description Non-Continuous Roll The media is wound on a core. Individual Media... -
Page 6: Ribbon
Bradyprinter THT MVPplus Quick Reference Guide Ribbon Ribbon Ribbon is a thin film that is coated on one side with wax, wax resin, or resin, and which is transferred to the media during the thermal transfer process. When To Use Ribbon Thermal transfer media requires ribbon for printing while direct thermal media does not. -
Page 7: Load The Media
Bradyprinter THT MVPplus Quick Reference Guide Load the Media Load the Media This procedure is for loading media in Tear-Off Mode. For loading either fanfold media or roll media with a printer option, refer to the User Guide. Figure 3. Press the printhead open lever. -
Page 8: Position The Transmissive Sensor
Bradyprinter THT MVPplus Quick Reference Guide Position the Transmissive Sensor Position the Transmissive Sensor This printer uses two types of media sensors: transmissive and reflective. By default, the printer uses the transmissive sensor, which you can adjust for optimal print performance. The reflective sensor is a secondary media sensing system that is activated only if the transmissive sensor cannot be used to calibrate the media. - Page 9 Bradyprinter THT MVPplus Quick Reference Guide Position the Transmissive Sensor To adjust the transmissive sensor: Press the printhead open lever. The printhead assembly springs up. Continue to pivot the printhead until it locks into place. Figure 4. Locate the transmissive sensor.
-
Page 10: Position The Reflective Sensor
Bradyprinter THT MVPplus Quick Reference Guide Position the Reflective Sensor Position the Reflective Sensor Note • This sensor is typically covered by a factory-installed plate. If you need to enable this sensor, you must remove the plate. Refer to Figure Open the printhead assembly and turn on the AC power. -
Page 11: Load The Ribbon
Bradyprinter THT MVPplus Quick Reference Guide Load the Ribbon Load the Ribbon Figure 7 • Load the Ribbon Ribbon take-up spindle Ribbon guide plate Ribbon supply spindle Printhead open lever Important • To protect the printhead from wear, always use ribbon that is wider than the media. -
Page 12: Front Panel
Bradyprinter THT MVPplus Quick Reference Guide Front Panel Front Panel Refer to Figure Figure 8 • Front Panel PAUSE Table 2 • Front Panel Buttons Front Panel Buttons Description FEED • Press once to feed one blank label. PAUSE • Press once to stop the printing process. - Page 13 Bradyprinter THT MVPplus Quick Reference Guide Front Panel Table 2 • Front Panel Buttons (Continued) Front Panel Buttons Description PLUS (+) Press (+) to: • scroll to the next selection • increase the value • answer “yes” • print a label (when applicable) MINUS (–)
-
Page 14: Configure The Printer
Bradyprinter THT MVPplus Quick Reference Guide Configure the Printer Configure the Printer The configuration procedure in the next table contains the information you need to get your printer up and running, but it is not comprehensive. Refer to the user guide for more information. -
Page 15: Print A Test Label
Bradyprinter THT MVPplus Quick Reference Guide Configure the Printer Print a Test Label To print a test label: Turn off the printer. Press and hold CANCEL while turning on the printer. Release CANCEL after the first front panel LED turns off. -
Page 16: Adjust Printhead Pressure
Bradyprinter THT MVPplus Quick Reference Guide Configure the Printer Adjust Printhead Pressure Refer to Figure 10. This adjustment may be necessary if printing is too light on one side or if thick media is used. Adjust printhead pressure to ensure maximum print quality. The amount of pressure required is determined by the type and thickness of the media as well as the media width. -
Page 17: Maintenance
Clean the Printer Note • Use only the cleaning agents indicated. Brady Corporation will not be responsible for damage caused by any other cleaning materials used on the printer. The following table provides a recommended cleaning schedule. Use a solvent of 90% isopropyl alcohol. -
Page 18: Replace The Fuse
Bradyprinter THT MVPplus Quick Reference Guide Maintenance Figure 11 • Clean the Printer Printhead Transmissive Take Label Sensor Sensor Reflective Ribbon Sensor Sensor Platen Roller Clean the Exterior Clean the exterior of the printer with a lint-free cloth. Do not use harsh, abrasive cleaning agents or solvents. - Page 20 Lindestraat 20 B-9240 Zele Belgium Telephone: 32 (0) 52 457 811 Facsimile: 32 (0) 52 457 812 website: www.bradyeurope.com Brady Corporation Asia Pte Ltd 55 Ayer Rajah Crescent #03-25 Ayer Rajah Industrial Estate Singapore 139949 Telephone: 65-6477-7261 Facsimile: 65-6775-7929 website: www.bradyid.com.sg...