Table of Contents
Advertisement
Quick Links
2562648A REV. A 1011
Safety Message to Installers of Siren Speakers
People's lives depend on your proper installation and servicing of Federal Signal products. It is important to
read and follow all instructions shipped with this product and the original product. Listed below are some
other important safety instructions and precautions you should follow:
Before Installation
Qualifications
•
To properly install an electronic siren, you must have a good understanding of automotive electrical
procedures and systems, along with proficiency in the installation and service of safety warning
equipment. Always refer to the vehicle's service manuals when installing equipment on a vehicle.
Sound Hazards
•
Your hearing and the hearing of others, in or near your emergency vehicle, could be damaged by
loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures
to moderately loud sounds. For hearing conservation guidance, refer to federal, state, or local
recommendations. OSHA Standard 1910.95 offers guidance on "Permissible Noise Exposure."
•
All effective sirens and horns produce loud sounds (120 dB) that may cause permanent hearing loss.
Always minimize your exposure to the sound of the siren or horn and wear hearing protection. Do not
sound the siren or horn indoors or in enclosed areas where you and others will be exposed to the sound.
•
Federal Signal siren amplifiers and speakers are designed to work together as a system. Combining a
siren and speaker from different manufacturers may reduce the warning effectiveness of the siren system
and may damage the components. You should verify or test your combination to make sure the system
works together properly and meets federal, state and local standards or guidelines.
During Installation
•
DO NOT get metal shavings inside the product. Metal shavings can cause the system to fail. If drilling
must be done near the unit, place an ESD-approved cover over the unit to prevent metal shavings from
entering the unit. Inspect the unit after mounting to be sure there are no shavings present in or near the unit.
•
To avoid a battery explosion, always disconnect the negative battery cable first and reconnect it last.
Avoid causing a spark when connecting near or to the battery. The gases produced by a battery can
caused a battery explosion that could result in vehicle damage and serious injury.
•
DO NOT connect this system to the vehicle battery until ALL other electrical connections are made,
mounting of all components is complete, and you have verified that no shorts exist. If wiring is shorted
to the vehicle frame, high current conductors can cause hazardous sparks resulting in electrical fires or
flying molten metal.
•
Be sure the siren amplifier and speaker(s) in your installation have compatible wattage ratings.
•
In order for the electronic siren to function properly, the ground connection must be made to the
NEGATIVE battery terminal.
Model RB-CAP11 Mounting Kit for the Rumbler
Speaker in a 2011 and Newer Chevy
®
Caprice
®
Advertisement
Table of Contents
Related Manuals for Federal Signal Corporation RB-CAP11
Summary of Contents for Federal Signal Corporation RB-CAP11
- Page 1 Model RB-CAP11 Mounting Kit for the Rumbler ® Speaker in a 2011 and Newer Chevy Caprice ® 2562648A REV. A 1011 Safety Message to Installers of Siren Speakers People’s lives depend on your proper installation and servicing of Federal Signal products. It is important to read and follow all instructions shipped with this product and the original product.
- Page 2 After Installation • After installation, test the siren system and light system to ensure that it is operating properly. • Test all vehicle functions, including horn operation, vehicle safety functions and vehicle light systems, to ensure proper operation. Ensure that installation has not affected vehicle operation or changed any vehicle safety function or circuit. • After testing is complete, provide a copy of these instructions to the instructional staff and all operating personnel. • File these instructions in a safe place and refer to them when maintaining or reinstalling the product. Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death. Model RB-CAP11 Speaker Mounting Kit...
-
Page 3: Product Overview
Instruction manuals are available for viewing or downloading at www.fedsig.com. Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death. Model RB-CAP11 Speaker Mounting Kit... - Page 4 Figure 1 Step bracket and bands positioned against cross member STEP BRACKET CROSS MEMBER BEHIND REAR BUMPER LONG BAND FACING REAR OF VEHICLE SPARE-TIRE WELL 290A6752 3. See Figure 2 on page 5 and Figure 3 on page 6. Loosely assemble the Rumbler speaker in the long and short bands using a 5/16" x 1-1/4" bolt in the hole in the bottom of the band tabs. The short band faces the front of the vehicle. Insert two 5/16"-18 x 2-1/2" bolts through the step bracket and bands, and then place two spacers on each bolt. Model RB-CAP11 Speaker Mounting Kit...
- Page 5 Mounting Rumbler Speakers in a 2011 and Newer Chevy Caprice ® ® Figure 2 Exploded view of Rumbler in bands secured in place with step bracket Model RB-CAP11 Speaker Mounting Kit...
- Page 6 Figure 3 Rumbler in bands secured in place with step brackets STEP BRACKET SPACERS HEATSHIELD CLAMP LONG BAND 8. After you mount the speakers, connect the supplied wire harness to the leads from the Rumbler amplifier. Note that two speakers must be connected in parallel and in phase. For details, refer to the instructions included with the amplifier. See Figure 4 below and Figure 5 on page 7. Remove an approximately 3" x 6" section on each end of the lower splash panel for speaker clearance. Figure 4 Two 3" x 6" sections marked in lower splash panel Model RB-CAP11 Speaker Mounting Kit...
- Page 7 Qualifications • To properly use an electronic siren and speaker(s), you must have a good understanding of general vehicle operation, a high proficiency in the use of safety warning equipment, and thorough knowledge of state and federal UNIFORM TRAFFIC CODES. Sound Hazards • Your hearing and the hearing of others, in or close to your emergency vehicle, could be damaged by loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures to moderately loud sounds. For hearing conservation guidance, refer to federal, state, or local recommendations. OSHA Standard 1910.95 offers guidance on “Permissible Noise Exposure.” • All effective sirens and horns produce loud sounds (120 dB) that may cause permanent hearing loss. Always minimize your exposure to siren sound, roll up your windows and wear hearing protection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound. Only use the siren for emergency response situations. Sound Limitations • Before using the vehicle, check to see if the siren speakers are concealed from view. If the siren speaker is not in clear view on the front of the vehicle, use extra caution when operating the vehicle. A concealed siren speaker installation is less effective at warning others. Model RB-CAP11 Speaker Mounting Kit...
-
Page 8: Testing The Installation
Do not stare directly into the lights at a close range or permanent damage to your eyesight may occur. After testing the installation, test the emergency warning system to ensure that it is operating properly. Also test all vehicle functions, including horn operation, vehicle safety functions, and vehicle lighting systems to ensure proper operation. Ensure that the installation has not affected the vehicle operation or changed any vehicle safety functions or circuits. Model RB-CAP11 Speaker Mounting Kit... -
Page 9: Getting Technical Support And Service
Federal Signal Corporation Phone: 1-800-264-3578 Returning a Product to Federal Signal Before returning a product to Federal Signal, call 800-264-3578, 800-433-9132, or 800-824-0254 to obtain a Returned Merchandise Authorization number (RMA number). To expedite the process please be prepared with the following information: • Your Federal Signal customer or account number. • The purchase order number under which the items were purchased. • The shipping method. • The model or part number of the product being returned. • The quantity of products being returned. • Drop ship information as needed. • Any estimate required. When you receive your RMA Number: • Write the RMA number on the outside of the box of returned items. • Reference the RMA number on your paperwork inside of the box. • Write the RMA number down, so that you can easily check on status of the returned equipment. Model RB-CAP11 Speaker Mounting Kit... - Page 10 Mounting Rumbler Speakers in a 2011 and Newer Chevy Caprice ® ® Send all material with the issued RMA Number to: Federal Signal Corporation Public Safety Systems 2645 Federal Signal Drive University Park, IL 60484-3167 Attn: Service Department RMA: #__________ 800-433-9132 800-343-9706 (fax) www.fedsig.com Model RB-CAP11 Speaker Mounting Kit...
- Page 11 © 2011 Federal Signal Corporation Rumbler is a trademark of Federal Signal Corporation. Chevy and Chevrolet are registered trademarks of General Motors Corporation.
- Page 12 2645 Federal Signal Drive, University Park, IL 60484-3167 Tel.: (800) 264-3578 • Fax: (800) 682-8022 www.fedsig.com...