Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for XTZ Cinema Series
Summary of Contents for XTZ Cinema Series
- Page 1 Cinema Series Sub 1x12 Owners Manual...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS CAUTION! RISK OF ELECTRIC SHOCK DO NOT OPEN USE IN DRY LOCATIONS ONLY The lighting flash with arrowhead CAUTION: The exclamation point symbol, within TO PREVENT THE RISK OF ELECTRIC symbol, within an equilateral triangle, is an equilateral triangle, is intended SHOCK, DO NOT REMOVE COVER intended to alert the user to the presence to alert the user to the presence of... -
Page 3: Table Of Contents
CONTENTS Introduction..............4 About XTZ................ 4 Product information............5 Installation..............6 Calibration............... 9 Connections & controls............11 Care of your speaker............. 12 Protection circuitry............12 Troubleshooting and service......... 13 Technical specifications........... 14 Service & support............15... -
Page 4: Introduction
Introduction Introduction Congratulations on your purchase of XTZ subwoofer/-s. This product represents the state of the art in subwoofer performance and will provide you with years of listening pleasure when properly setup and cared for. We strongly urge you to read this owner’s manual and follow the instructions provided to help you attain maximum system performance. -
Page 5: Product Information
NOTE: Remember to make all equipment connections with system power disconnected to reduce the risk of personal shock or damage to equipment. Consult your dealer or info@xtz.se for optional accessories that may be required to properly complete your system installation. -
Page 6: Installation
Installation Cables - RCA unbalanced When installing your new subwoofer using unbalanced RCA connections, you should use high quality shielded phono cables. Poor quality cables may pickup interference and result in hum or noise. Keep the length of cable as short as possible and route all input signal cables away from power cables to reduce the potential for induced noise. - Page 7 Caution This subwoofer has electronics built into the cabinet and must be properly ventilated. Do not place the rear of cabinet against a wall, you must allow room for adequate ventilation of the amplifier (at least 2 inches). Do not place the subwoofer next to heat sources, such as furnace registers, radiators, etc. Do not place the subwoofer near sources of excessive moisture, such as evaporative coolers, humidifiers, etc.
- Page 8 Multiple subwoofers When connecting multiple subwoofers using RCA signal connections, you will need to use “Y” cables (signal splitters) to route your receiver/processor output to each woofer if it does not have multiple “SUBWOOFER” output jacks. Another option is to use an XLR to RCA adapter to convert your receiver/processor RCA signal ouptut to an XLR connection, which allows you to use the XLR “DIRECT PASS-THRU”.
-
Page 9: Calibration
Calibration Introduction For optimal performance, you should calibrate your system to ensure proper level matching between all speakers and the proper setting of all controls (including crossover frequency, phase, and any channel delays your receiver/processor may offer). This procedure will vary depending on system configuration and the information below is provided as a basic guide to assist you. - Page 10 Do not be afraid to experiment with slight adjustments to find what may improve the sound in your system and room the best! Do not hesitate to contact us at info@xtz.se for questions about settings. We are happy to assist you in optimizing your system!
-
Page 11: Connections & Controls
Connections & controls XLR Balanced Input (1) Professional style balanced XLR input. Note, all inputs are summed together (L/R RCA & XLR). XLR Direct Pass-Thru Professional style balanced XLR pass through (unbuffered) (XLR Output) (2) RCA Input (3) Consumer style unbalanced RCA inputs. Note, all inputs are summed together (L/R RCA & XLR). Low Pass Filter Switch - This switch removes the subwoofer’s built in electronic crossover circuitry from the signal path. -
Page 12: Care Of Your Speaker
Power Indicator Light (10) This LED indicates the operating mode of the subwoofer. Green indicates normal “ON” operation. Red indicates the subwoofer is in a low power “standby” mode. Power Switch (11) The master power switch is located on the lower half of the unit. This rocker style switch is the main on/off for the unit. -
Page 13: Troubleshooting And Service
Troubleshooting and service If you should experience a problem with the operation of your subwoofer, please check all of the following before seeking service. Following is a simple troubleshooting guide to assist you. Verify unit is plugged in and that the power outlet used supplies the proper AC voltage & current. Is the power switch on? Has the external fuse blown? Unplug the power cord from the amplifier, then use a small screwdriver to remove the fuse holder cartridge (located below the cord connection), and inspect fuse for damage. -
Page 14: Technical Specifications
Technical specifications Driver size 12” High Speed Driver Magnet weight 96 oz. (6.0 lbs/2.7 kg) Voice coil 2” four layer Anechoic EQ 19 Hz - 160 Hz (Ported), 24 Hz - 160 Hz (Closed) Room Gain EQ 30 Hz - 160 Hz (Ported), 36 Hz - 160 Hz (Closed) Variable low pass crossover 40 Hz - 160 Hz 24 dB/octave... -
Page 15: Service & Support
Service & support ”Do It Yourself” - service We apply “do-it-yourself” service on all XTZ products. If you by yourself are able to find out what part To aid service, XTZ products are con- structed and produced using com- of the loudspeaker is defective, you are fully allowed to unmount that part (which would normally be a mon technology, so that basically driver, a filter or the amplifier) and send it back to us for exchange.