Assign Settings (Asgn 1-8: ) - Boss GP-10 Owner's Manual

Effects/Patch Settings
Example setting
When a specific patch is selected, use the expression pedal to control the
volume of the modeling
Select the patch whose settings you want to edit, then make the following
parameter settings.
Button Parameter
[SYSTEM]
SysCtl: EXP1on Fnc
[EFFECTS] Ctl: EXP1on Func
Assign Settings
(Asgn 1–8: )
For each parameter, you can specify, in detail, which controller will control which parameter.
You can use Assign 1–8 to make eight different sets of settings.
* This is available if the Sys: Controller (p. 13) is set to "PATCH SETTING. "
Parameter Explanation
On/Off
Turns Assign 1–8 on/off.
Selects the parameter that will be controlled. For details on the parameters,
Target
refer to the explanations of each parameter in this manual.
Target Min
Specifies the range of change for the parameter. The values will depend on
the parameter that's assigned by Target.
Target Max
Selects the controller to which the function will be assigned.
[CTL 1] [CTL 2] pedals of this unit and external footswitch
CTL 1–CTL 4
(CTL 3, CTL 4)
GK S1,
[S1] [S2] buttons of the GK pickup
GK S2
GK VOL Volume knob of the GK pickup
EXP1 SW
Expression pedal switch
EXP1 ON Expression pedal when the expression pedal switch is on
EXP1 OFF Expression pedal when the expression pedal switch is off
EXP2
External expression pedal
Internal pedal
The virtual expression pedal will begin
Source
operating when started by the specified
INT PDL trigger (Int Pedal Trig), modifying the
parameter specified by "Target. "
For details on the parameters that can be assigned to the
internal pedal, refer to "Int Pedal Time" and "Int Pedal Curve. "
Wave pedal
The virtual expression pedal will cyclically modify the
parameter specified by "Target" in a fixed wave form.
WAVE PDL
CC#1–31,
Control change number from an external MIDI device
CC#64–95
The value will normally be off (minimum value), and will
be on (maximum value) only while the control is being
operated.
MOMENTARY
Src Mode
* If you want to use the internal pedal or wave pedal, set
The value will toggle between off (minimum) and on
TOGGLE
(maximum) each time the control is operated.
Within the operating range of the source, this specifies the range that will
S. Range Min
control the target parameter.
S. Range Max
The target parameter will be controlled within the range specified. Normally,
you should leave Range Min at "0" and Range Max at "127. "
Specifies how the motion of the internal pedal will be triggered.
PATCH
Triggered when you switch patches.
CHANGE
CTL 1–4 Triggered when you operate the [CTL] pedal.
EXP1 SW Triggered when you operate the expression pedal switch.
Triggered when you move the expression pedal to
EXP1 OFF LOW
minimum.
Triggered when you depress the expression pedal through
EXP1 OFF MID
the center value.
Triggered when you move the expression pedal to
Int Pdl Trig *1
EXP1 OFF HI
maximum.
Triggered when you move the expression pedal to
EXP1 ON LOW
minimum while the expression pedal switch is on.
Triggered when you depress the expression pedal through
EXP1 ON MID
the center value while the expression pedal switch is on.
Triggered when you move the expression pedal to
EXP1 ON HI
maximum while the expression pedal switch is on.
EXP2 Triggered when you move the external expression pedal.
GK S1
Triggered when you operate the [S1]/[S2] button of the GK
pickup.
GK S2
Specifies the time over which the internal pedal will move from the released
Int Pdl Time *1
(heel) position to the depressed (toe) position.
Select one of the following curves to specify the change
produced by the internal pedal.
LINEAR
LINEAR,
Int Pdl Curve *1 SLOW RISE,
FAST RISE
Wav Pdl Rate *2 Specifies the time for one cycle of the wave pedal.
12
Value
PATCH SETTING
MODELING VOL
to "MOMENTARY. "
SLOW RISE FAST RISE
Parameter Explanation
Select one of the following to specify the change produced
by the wave pedal.
SAW
WPdWavFrm *2 SAW, TRI, SIN
*1 Source=INT PDL only
*2 Source=WAVE PDL only
Example setting
Make smoothly bend up one octave when you press the [CTL 1] pedal
Select the patch whose settings you want to edit, and then make the following
parameter settings.
Button Parameter
[SYSTEM] SysCtl: CTL1 Func
Fx: Type
Asgn1: On/Off
Asgn1: Target
Asgn1: Target Min
Asgn1: Target Max
Asgn1: Source
Asgn1: Src Mode
[EFFECTS]
Asgn1: S. Range Min
Asgn1: S. Range Max
Asgn1: Int Pdl Trig
Asgn1: Int Pdl Time
Asgn1: Int Pdl Curve
For guitar solos, you want to be able to step on the [CTL 1] pedal to switch
AMP to solo mode
Button Parameter
[SYSTEM] Sys: CTL 1 Func
Asgn1: On/Off
Asgn1: Target
Asgn1: Target Min
Asgn1: Target Max
Asgn1: Source
Asgn1: Src Mode
Asgn1: S. Range Min
Asgn1: S. Range Max
[EFFECTS]
Asgn2: On/Off
Asgn2: Target
Asgn2: Target Min
Asgn2: Target Max
Asgn2: Source
Asgn2: Src Mode
Asgn2: S. Range Min
Asgn2: S. Range Max
TRIANGLE SINE
Value
PATCH SETTING
PEDAL BEND
ON
FXP.BND: POSITION
0
100
INT PDL
MOMENTARY
0
127
CTL 1
20
(Adjust the time over which the pitch rises an octave.)
LINEAR
(You can select a different curve to modify the way in
which the change occurs.)
Value
PATCH SETTING
ON
AMP: SOLO SW
OFF
ON
CTL 1
TOGGLE
0
127
ON
AMP: GAIN SW
LOW
MID
CTL 1
TOGGLE
0
127