Electrical Precautions; Outdoor Installation; Drainage; Indoor Installations - Jacuzzi Tirage Plus PORTABLE WHIRLPOOL SPA Owner's Manual

CAUTION:
Do not apply electrical power to the
spa unless it is filled with water to the normal
water level, which is approx. 7" below the spa rim
(see location of water level indicator on face of
skimmer on page 6). If the spa's motor/pumps are
actuated when there is not sufficient water in the
unit, the circulation pump could be irreparably
damaged. Not heeding this caution will nullify the
warranty. In addition to damaging the unit, oper-
ating the unit with insufficient water could cause
a fire.
Do not locate lighting fixtures directly above the spa;
lighting and electrical receptacles must be located at
least 5 ft. from the spa. Lighting located between 5
and 10 ft. from the spa must be on a circuit protected
by a GFCI. (See National Electrical Code, 680-6.)
Do not use electrically connected devices, such as

Outdoor Installation

If you install the spa outdoors, we
that you provide a concrete pad for it to rest on. To do
this, construct forms for a 8' x 8' x 4" (approx.) thick
level pad. Install a #10 gauge wire mesh 6" x 6" steel
reinforced grid. Attach a #8 solid copper wire to the
grid with a ground clamp. This wire should be long
enough to reach the bond bar on the spa System
Control Module (min. 36"), but should not be located
under the base of the spa. Then pour the concrete
pad.

Drainage

Whether you install your spa indoors or outdoors,
you can drain it almost completely by attaching a
garden hose to the drain valve located on the suction
tee of the spa. Simply run the hose to the house sewer
line or drain field and open the drain valve. See inside
back cover for a quicker, permanent drain method.
BOND BAR
HOLE IN PAN FOR
DRAIN HOSE
#8 BOND WIRE
(TO HOUSE
ELECTRICAL
PANEL OR LOCAL
BOND)
TO
BOND
BAR
INSTALLATION

Electrical Precautions

television, radio, toys, telephones, stereo speakers,
lights or cooking devices within 5 ft. of the spa when
the spa is being used.
Bonding and Grounding
All fixed metal objects located within 5 ft. of the spa,
such as fence posts, railings, door frames green-
house structures, gutters, etc., must be attached to
the bonding bar on the outside of the spa electrical
cabinet using #8 solid copper wire. With #8 solid
copper wire, bond the spa to the house electrical
panel or approved local bond.
An approved ground may be an 8 ft. long ground
rod, a plate electrode, or a buried metal water
pipe with at least 10 ft. of buried pipe. Check your
local building code for requirements. Bonding
lugs are available at your local electrical supply
store. (Bond bar location is shown on page 5 .)
Make sure the area surrounding the spa has good
recommend
drainage to keep water from collecting at the base of the
spa--especially near the equipment area. If drainage is
poor, install a drain line and/or gravel drain field (see
illustration below).

Indoor Installations

Water which splashes on the floor during use of the
spa may cause a walking hazard and/or structural dam-
age
waterproof building materials are used in the area sur-
rounding and beneath the spa. Take into consideration,
also, the high room humidity which will exist due to high
spa water temperatures. Providing natural or forced
ventilation of the room will help maintain comfort and
minimize moisture damage to the building. Jacuzzi
Whirlpool Bath is not responsible for damages resulting
from excess moisture or water spillage. Consult an
architect or engineer for aid in designing your indoor
installation.
HOLE FOR
DRAIN VALVE
ELECTRICAL CONDUIT
(HOSE BIBB)
unless good drainage is provided and proper
WIRE MESH GRID
8' X 8' X 4"
THICK
CONCRETE
PAD
GRAVEL
DRAIN
FIELD
4