1. Manuals
  2. Brands
  3. scope Manuals
  4. Remote Control
  5. DataPage Mark 2
  6. Installation & user manual

scope DataPage Mark 2 Installation & User Manual

Desktop uhf radio paging system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DataP
DataP
DataP age MK2
DataP
DataP
Desktop UHF Radio Paging System
Installation & User Manual
Scope Communications UK Ltd, Quantum House, Steamer Quay, Totnes, Devon TQ9 5AL
Tel: +44 1803 860700 Fax: +44 1803 863716 Email: sales@scope-uk.com Web: www.scope-uk.com
age MK2
age MK2
age MK2
age MK2
DPMK2/6

Advertisement

Table of Contents
loading

Related Manuals for scope DataPage Mark 2

Summary of Contents for scope DataPage Mark 2

  • Page 1 MK2 DataP DataP age MK2 Desktop UHF Radio Paging System Installation & User Manual Scope Communications UK Ltd, Quantum House, Steamer Quay, Totnes, Devon TQ9 5AL Tel: +44 1803 860700 Fax: +44 1803 863716 Email: sales@scope-uk.com Web: www.scope-uk.com DPMK2/6...

  • Page 2: Important Installation Information

    For UK equipment, Scope has no control of the use and application of the frequencies issued by OFCOM. Some equipment that is licensed may have greater protection than other equipment which is operated on a WT Act License Exempt basis.

  • Page 3: Installation

    Liability Scope does not accept liability for any damage or injury, howsoever caused as the result of misuse of this equipment. It is the responsibility of the user to ensure that the equipment is operated in the manner for which it was intended and that it is the correct item of equipment for the required task.
  • Page 4 The relevant clauses on the Of21 form should be completed as follows: Section 2, item 9. Tick “Self-Select PBR licence” Section 4, item 28. Generally, antennas provided by Scope are Omni-Directional, with a gain of 0 dB. Section 4, item 30. ERP level: 0.5W as standard, 2W if the optional amplifier is fitted.
  • Page 5 Scope DataPage UHF MK2 Radio Paging System Description: Your DataPage Mark 2 is supplied in one of three configurations: 1) NDP, the basic model, provides keyboard entry of data for message transmission. Additionally, two volt-free (dry) contacts are provided for sending pre-programmed messages.
  • Page 6 Scope DataPage UHF MK2 Radio Paging System System Operation 1) Connect the 90 degree aerial to the BNC connector (bayonet twist lock) located at the side of the transmitter. Slide the plastic cover over the connector, engaging the two lugs into the corresponding recesses in the side of the case.
  • Page 7 Scope DataPage UHF MK2 Radio Paging System Fig. 1 Connecting the antenna and locking cover Fig. 2 Connection port detail DPMK2/6 07/05...
  • Page 8 Scope DataPage UHF MK2 Radio Paging System Group Calls As previously stated, this system will accept pager identities from number 1 through 9,999. Most pagers will accept a minimum of two identities, enabling the pager to respond to selected group calls as well as its own unique identity.

  • Page 9: Transmit Speed

    Scope DataPage UHF MK2 Radio Paging System Program Parameters The standard models are factory pre-set and should not under any circumstances be adjusted by the customer. The factory settings can be viewed for the purposes of verification when ordering additional components etc.
  • Page 10 Scope DataPage UHF MK2 Radio Paging System Pressing key 1 will display Normally Open Pressing key 2 will display Normally Closed Pressing key 3 will display Change of State After making your selection, press ENTER to store. Display will change to: TRIG.
  • Page 11 Scope DataPage UHF MK2 Radio Paging System 3: Phone (refer also to Section 2: Telephone Interface This section is only applicable to models: NDPDTMF, NDPLP The telephone interface can be programmed through the keyboard as follows: Press key 3. The screen will change to display:- RINGS TO ANSWER: >...

  • Page 12: Enter Password

    Scope DataPage UHF MK2 Radio Paging System 4: Serial After pressing ENTER, the display will change to: STOP BITS (1-2): > Enter a number in the range 1-2 to set. After pressing ENTER, the display will change to: Serial Port Set OK.
  • Page 13 PSTN. The Scope digital paging interface can be used to transmit text or numeric messages from any telephone connected to your exchange, direct to the pocket of the individual being paged. There are two types of interface available, these cover all types of keyphone, hybrid and PABX systems with DTMF capability.
  • Page 14 SIGN-ON TONES' to allow valid data to be sent before receiving the sign-on tones. Tone only paging Numeric and alphanumeric pagers can receive tone only calls by entering in place of the message. © Scope Communications UK Ltd, 2003 All Rights Reserved DPMK2/6 07/05...

Table of Contents