1. Manuals
  2. Brands
  3. scope Manuals
  4. Remote Control
  5. CONX8E/3
  6. Installation & user manual

scope CONX8E/3 Installation & User Manual

Rs232 radio paging system (triple port, mains euro version)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ConneXions
ConneXions
ConneXions
ConneXions
ConneXions
RS232 Radio Paging System (Triple Port, Mains Euro Version)
Installation & User Manual
Scope Communications UK Ltd, Quantum House, Steamer Quay, Totnes TQ9 5AL, England, UK
Tel: +44 1803 860700 Fax: +44 1803 863716 E-Mail: sales@scope-uk.com Web: www.scope-uk.com
CONX8E/3
ConneXions
ConneXions
ConneXions
ConneXions
ConneXions
II
CONX8E/3MAN3

Advertisement

Table of Contents
loading

Related Manuals for scope CONX8E/3

Summary of Contents for scope CONX8E/3

  • Page 1 RS232 Radio Paging System (Triple Port, Mains Euro Version) Installation & User Manual ConneXions ConneXions ConneXions ConneXions ConneXions Scope Communications UK Ltd, Quantum House, Steamer Quay, Totnes TQ9 5AL, England, UK Tel: +44 1803 860700 Fax: +44 1803 863716 E-Mail: sales@scope-uk.com Web: www.scope-uk.com CONX8E/3MAN3...

  • Page 2: Important Installation Information

    For UK equipment, Scope has no control of the use and application of the frequencies issued by OFCOM. Some equipment that is licensed may have greater protection than other equipment which is operated on a WT Act License Exempt basis.

  • Page 3: Warranty

    Liability Scope does not accept liability for any damage or injury, howsoever caused as the result of misuse of this equipment. It is the responsibility of the user to ensure that the equipment is operated in the manner for which it was intended and that it is the correct item of equipment for the required task.

  • Page 4: System Overview

    ConneXions II V8 (Euro), Multi Port Version System Overview The Scope ConneXions II V8 (Euro) is a POCSAG data display radio paging system which can be used to transmit both text and numeric messages direct to pocket pagers carried by individuals or entire groups.
  • Page 5 Warning! Never transmit without an aerial attached to the transmitter Warning! Carefully check the Installation section in this manual covering data pin connections prior to installation. Damage caused by incorrect connection is the responsibility of the installer! CONX8E/3 Issue 3...

  • Page 6: Installation

    (DTR) OUT GROUND (GND) REQUEST TO SEND (RTS) OUT CLEAR TO SEND (CTS) IN +5V 100mA max (PL2 only) (for Scope peripherals) PL1 SERIAL PORT (25 way D type plug) SIGNAL DIRECTION TRANSMIT DATA (TX) OUT RECEIVE DATA (RX) IN...
  • Page 7 LED on the base of the unit will light momentarily. Radio Transmission Baud Rate This is fixed at the factory to suit the pagers supplied and will normally be set at either 512 or 1200 baud CONX8E/3 Issue 3...
  • Page 8 ConneXions II V8 (Euro), Multi Port Version CONX8E/3 Issue 3...

  • Page 9: Section 2: System Operation

    20 numeric digits. As a default, contacts are programmed as Normally Open (N/O), with a repeat transmission every two minutes if still active. Note: repeats are not available where contacts are programmed as Normally Closed (N/C). CONX8E/3 Issue 3...

  • Page 10: Other Antennas

    In the event that a pager requires service, return it directly to Scope in the pre-addressed service bag supplied with your system by registered post. Ensure that you carefully fill out the service form provided.

  • Page 11: System Specification

    PL1, PL2: 1200 Baud. PL3: 9600 Baud* Footprint (mm): 328 (L) x 190 (W) x 75 (D) max *dependent on system configuration excluding aerial Scope’s policy is one of continuous development and specifications are subject to change without notice CONX8E/3 Issue 3...

  • Page 12: Section 3: Technical Information

    Numeric Pagers Example serial message string:- N0012300A1234567890<CR> The ‘N’ informs the transcoder that this message is destined for a Numeric pager. Any data not preceded by this will be ignored. CONX8E/3 Issue 3...
  • Page 13 To change the transmission baud rate in a message string, placing a letter “N” after the “A” will alter it to 512 baud. Placing a letter “F” after the “A” will alter it to 1200 baud. The default setting for the Connexions II V8 (Euro) is 1200 baud. ************************************************************************ CONX8E/3 Issue 3...

Table of Contents