It 1. Charge Your Headset; Nl 2. Turning Your Headset On And Off; Su 3. Pair It With Your Phone; Wear It How You Like It - Jabra BT5010 User Manual

1. Charge your headset
GB
Make sure that your Jabra BT5010 headset is fully charged for two hours
F
before you start using it. Use the AC adapter to charge from a power socket,
or charge directly from your PC with the USB cable provided. Use only the
ES
chargers provided in the box – do not use chargers from any other devices
as this might damage your Jabra BT5010.
PT
Connect your headset as shown in fig 2. When the LED indicator light is solid
red, your headset is charging. When the LED indicator light is green, it is fully
DE
charged.
IT
2. Turning your headset on and off
• Press the on/off/pairing button to turn on your headset (see fig 1).
NL
The LED will show the battery status to indicate the Jabra BT5010 is on
(see section 7).
SU
• Press the on/off/pairing button to turn off your headset until you see a
burst of flashes.
NO
3. Pair it with your phone
SE
Before you use your Jabra BT5010, you need to pair it with your mobile
DK
phone.
1. Put the headset in pairing mode
GR
• Make sure the headset is off.
• Press the on/off/pairing button marked
solid blue.
2. Set your Bluetooth phone to 'discover' the Jabra BT5010
Follow your phone's instruction guide. This usually involves going to a
'setup, ' 'connect' or 'Bluetooth' menu on your phone and selecting the
option to 'discover' or 'add' a Bluetooth device.* (See example from a
typical mobile phone in fig 3).
3. Your phone will find the Jabra BT5010
Your phone then asks if you want to pair with it. Accept by pressing
'Yes' or 'OK' on the phone and confirm with the passkey or PIN = 0000
(4 zeros). Your phone will confirm when pairing is complete. In case of
unsuccessful pairing, repeat steps 1 to 3.

until the LED indicator light is
R EL E AS E YOUR J AB R A

4. Wear it how you like it

The Jabra BT5010 is ready to wear on your right ear. If you prefer the left, pull
out the earhook and rotate and insert as shown. (See fig 4).
For optimal performance, wear the Jabra BT5010 and your mobile
phone on the same side of your body or within line of sight. In general,
you will get better performance when there are no obstructions
between your headset and your mobile phone. (See fig 5)

5. The sliding boom arm

The sliding boom arm is used for answering and ending calls, but will also
give an increased audio quality when extended.
To answer an incoming call just extend the boom arm to an open position
and to end the call slide the boom arm back to a closed position.
The Jabra BT5010 can of course be used with the boom arm in both
positions, but will provide the best audio quality when in the open position.

6. How to...

Answer a call
• Tap the answer/end button on your headset to answer a call
or
• Open the sliding boom arm to answer the call
End a call
• Tap the answer/end button to end an active call
or
• Close the sliding boom arm to end an active call
Make a call
• When you make a call from your mobile phone, the call will (subject to
phone settings) automatically transfer to your headset. If your phone
does not allow this feature, tap on the Jabra BT5010's answer/end
button to transfer the call to the headset.
Reject a call*
• Press the answer/end button when the phone rings to reject an
incoming call. Depending on your phone settings, the person who called
you will either be forwarded to your voice mail or hear a busy signal.
Jabra BT5010 Bluetooth headset
GB
F
ES
PT
DE
IT
NL
SU
NO
SE
DK
GR