Mitsubishi Electric City Multi PQHY-P72 Service Handbook page 97

[ IV Remote Controller ]
2. Remote controller function selection via the MA remote controller
(1) Remote controller function
The settings for the following remote controller functions can be changed in the remote controller function selection mode.
Change the settings as necessary.
Category 1
1.Language selection
Select the language in which the menu appears.
( CHANGE LANGUAGE )
(1) Function lock setting ( LOCKING FUNCTION )
2.Function lock
( FUNCTION SELEC- (2) Use of automatic mode ( SELECT AUTO MODE )
TION )
(3) Temperature range setting ( LIMIT TEMP FUNCTION )
(1) Remote controller main/sub setting ( CONTROLLER MAIN/SUB )
3.Mode selection
( MODE SELECTION )
(2) Clock enable/disable function ( CLOCK )
(3) Timer function setting ( WEEKLY TIMER )
(4)Technical assistance contact number setting ( CALL )
4.Display mode
(1) Temperature unit selection ( TEMP MODE C/ F )
( DISP MODE SETTING )
(2) Suction air temperature display setting ( ROOM TEMP DISP SELECT )
(3) Automatic cooling/heating display setting ( AUTO MODE DISP C/H )
[Function selection flowchart]
[1] Stop the air conditioner to start the remote controller function selection mode.
[4] Make the setting. [5] Setting completed
Normal display (Display that appears
when the air condition is stopped)
(Press and hold the
for two seconds.)
*The display cannot be changed during function selection,
test run, and self-diagnosis.
Category 1
Language selection
( CHANGE LANGUAGE )
Press the
button.
E
Function lock
( FUNCTION
SELECTION )
Press the Press the
button. button.
E
E
Press the
Mode selection
( MODE
SELECTION )
Press the
button.
E
Press the
Display mode
( DISP MODE
SETTING )
NOTE
Timer operation stops when the display is changed from remote controller function selection to normal display.
Category 2
[6] Go back to the normal display (Finish)
F
TEMP.
MENU ON/OFF
E
BACK MONITOR/SET DAY
PAR-21MAA CLOCK
G
C
E button and D button simultaneously
Remote controller function
selection mode
Press the button.
G
Function lock setting ( LOCKING FUNCTION )
Use of automatic mode ( SELECT AUTO MODE )
Press the
button.
G
Temperature range setting ( LIMIT TEMP FUNCTION )
Remote controller main/sub setting ( CONTROLLER MAIN/SUB )
Clock enable/disable function ( CLOCK )
G button.
Timer function setting ( WEEKLY TIMER )
Technical assistance contact number setting ( CALL )
Temperature unit selection ( TEMP MODE C/ F )
button.
G
Suction air temperature display setting ( ROOM TEMP DISP SELECT )
Automatic cooling/heating display setting ( AUTO MODE DISP C/H )
Category 3 (Setting content)
Multi-language display is supported.
Sets the type of locking to put into effect
Enables or disables automatic operation mode
Sets the adjustable temperature range (maximum, minimum)
Sets the remote controller as main or sub
* When two remote controllers are connected to the same group, one controller must be set as sub.
Enables or disables clock function
Sets the timer type
Contact number can be set to appear in case of error.
Sets the telephone number
Sets the temperature unit ( C or F) for display
Switches between display and non-display of indoor (suction) air temperature
Switches between display and non-display of
automatic mode
[2] Select from category 1.
Dot display
Messages are displayed in the
selected language.
All examples in this manual are
given in English
ON/OFF
I
A
FILTER
CHECK TEST
B
OPERATION
CLEAR
H
D
(Press and hold the
button simultaneously for two seconds.)
*The settings that are made according to
this procedure are stored in the remote
controller memory.
Category 2
Press the button.
G
Press the button.
G
Press the button.
G
- 88 -
Cool or Heat during
[3] Select from category 2.
E button and D
See [4]-1
Category 3
(Setting content)
See [4]-2. (1)
Press the
button.
D D
See [4]-2. (2)
See [4]-2. (3)
Press the
button.
D
See [4]-3. (1)
See [4]-3. (2)
See [4]-3. (3)
See [4]-3. (4)
Press the
button.
D
See [4]-4. (1)
See [4]-4. (2)
See [4]-4. (3)