For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit.
INSTALLATIONSHANDBUCH
Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen.
MANUEL D'INSTALLATION
Veuillez lire le manuel d'installation en entier avant d'installer ce climatiseur pour éviter tout accident et vous assurer d'une utilisation correcte.
MANUAL DE INSTALACIÓN
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de aire acondicionado.
MANUALE DI INSTALLAZIONE
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore d'aria.
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner installeert.
MANUAL DE INSTALAÇÃO
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade de ar condicionado.
Summary of Contents for Mitsubishi Electric CITY MULTI PQHY-P400YSGM-A
Page 1
Air-Conditioners For Building Application HEAT SOURCE UNIT PQHY-P400·500YSGM-A For use with R410A INSTALLATION MANUAL For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit. INSTALLATIONSHANDBUCH Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen. MANUEL D’INSTALLATION Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous assurer d’une utilisation correcte.
Page 2
[Fig. 5.0.1] [Fig. 6.2.1] = < 40° <A> = > = > (10) *1 <B> [Fig. 6.1.1] <A> 1990 (10) *1 45 45 <B> <A> Side-by-side installation <B> Back-to-back installation A Piping space (for side piping) B Heat exchanger unit C Compressor unit D Service space (front side) E (Top view)
Page 3
[Fig. 6.2.2] <A> <A> Side-by-side installation <B> Sample back-to-back installation (10) *1 G Piping space (for top piping) H Piping space (for side piping) I Heat exchanger unit J Compressor unit K Field-installed pipes Bypass pipe ø9.52 (Flare + Brazed) High press pipe ø19.05 (Flare + Brazed) Low press pipe ø25.4 (Flange + Brazed) L Connecting wire between heat exchanger unit and compressor unit (External...
Page 4
[Fig. 8.2.1] A Heat source unit B First branch C Indoor unit D Cap (mm) Å Heat source model ı Liquid pipe Ç Gas pipe Ï Downstream unit model total Ì Branch kit model P400 ø12.7 ø28.58 ~ 200 CMY-Y102S-G P500 ø15.88 ø28.58...
Page 5
[Fig. 9.3.1] [Fig. 9.3.2] <A> <B> A Nitrogen gas G Liquid pipe <A> Open A System analyzer J Valve <B> Closed B To indoor unit H Gas pipe B Lo knob K R410A cylinder C System analyzer I Heat source unit C Hi knob L Scale D Lo knob...
Page 6
10.2 [Fig. 10.2.1] A Power source B Transmission line L1 L2 L3 N M1M2 M1M2 S C Earth screw [Fig. 10.2.2] <A> <B> <C> CN102B CN103B CN102A CN103A CN102B <D> CN103B CN103A CN102A <E> <H> <G> CN101A <J> CN101B <I> <F>...
Page 7
10.3 [Fig. 10.3.1] <A> Change the jumper connec- CN40 (51) tor from CN41 to CN40 (01) (04) (05) (06) <B> SW2-1:ON M1 M2 M1 M2 S M1 M2 S M1 M2 S M1 M2 S M1 M2 S (105) (155) (101) <C>...
Contents 1. Safety precautions ..................8 8. Refrigerant piping installation ..............12 1.1. Before installation and electric work .......... 8 8.1. Caution ..................12 1.2. Precautions for devices that use R410A refrigerant ....8 8.2. Refrigerant piping system ............12 1.3.
• Use liquid refrigerant to fill the system. • The reverse phase of L lines (L ) can be detected (Error cord: 4103), - If gas refrigerant is used to seal the system, the composition of the refriger- but the reverse phase of L lines and N line can be not be detected. ant in the cylinder will change and performance may drop.
4. Confirmation of parts attached 1 Connecting pipe for heat 2 Connecting pipe 3 Connecting pipe for heat 4 Connecting pipe exchanger unit (Compressor unit - Heat exchanger unit (Compressor unit - Heat (Low press side ø28.58) exchanger unit ø28.58) (High press side ø22.2) exchanger unit ø9.52) PQY-P01YGM-A...
7. Water pipe installation • City Multi WR2 Series pipes are similar to other air-conditioning pipes, how- sealant particles, or rust, do not enter the pipes. ever, please observe the following precautions during installation. • Water Quality Processing 7.1. Precautions during installation 1 Depending on the quality of the cold-temperature water used in the air- conditioner, the copper piping of the heat exchanger may become cor- •...
8. Refrigerant piping installation City Multi WR2 Series is constituted by an end branching system in which the A Residues in commercially available antioxidants may have adverse effects on refrigerant piping from heat source unit is branched at BC controller and connected the equipment.
The total length of each liquid line is as follows: flare nut size (mm) ø19.05: E = 5 m dimension B ø15.88: A + B = 40 + 10 = 50 m outer diameter size in inches R410A ø12.7: C = 10 m ø6.35 1/4"...
Note: charging If a torque wrench is not available, use the following method as a standard: 1 Airtight test When you tighten the flare nut with a wrench, you will reach a point where Evacuate the connecting pipes and indoor units through the service port on the tightening torque will abruptly increase.
[Fig. 9.4.2] (P.5) When filling a gap with mortar, cover the penetration part with steel plate so that the insulation material will not be caved in. For this part, use incombustible materi- A Liquid pipe B Gas pipe C Electric wire als for both insulation and covering.
<Permissible Lengths> 1 M-NET Remote controller • Max length via outdoor units: L and L and L 500 m (1.25 mm or more) • Max transmission cable length: L and L and L and L and L 200 m (1.25 mm or more) •...
12. Information on rating plate Model PQHY-P400YGM-A PQHY-P500YGM-A PQY-P01YGM-A Refrigerant (R410A) – – 12.0 Allowable pressure (Ps) HP: 4.15 MPa, LP: 2.21 MPa Net weight MANUFACTURER: MITSUBISHI ELECTRIC CORPORATION AIR-CONDITIONING & REFRIGERATION SYSTEMS WORKS 5-66, TEBIRA, 6-CHOME, WAKAYAMA CITY, JAPAN...
Page 19
This product is designed and intended for use in the residential, commer- cial and light-industrial environment. • Low Voltage Directive 73/23/EEC The product at hand is • Electromagnetic Compatibility Directive 89/ based on the following EU regulations: 336/EEC Please be sure to put the contact address/telephone number on this manual before handing it to the customer.