Download Print this page

Advertisement

This service information is designed for experienced repair technicians only an is nor designed for use by the general
public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product. Products powered by electricity should be serviced or repaired only by experienced professional
technicians. Any attempt to service or repair the products dealt with in this service information by anyone else could
SERVICE MANUAL
Automatic Washing Machine
Model NO
WARNING
c year(Full name of the company who issues the service information).
All rights reserved. Una uthorized copying and distribution is a violation of law.
Haier Group
HLP24E
Order NO. TL1001S001V0

Advertisement

Troubleshooting

   Also See for Haier HLP24E

   Related Manuals for Haier HLP24E

   Summary of Contents for Haier HLP24E

  • Page 1: Service Manual

    SERVICE MANUAL Order NO. TL1001S001V0 Automatic Washing Machine HLP24E Model NO WARNING This service information is designed for experienced repair technicians only an is nor designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.

  • Page 2: Table Of Contents

    Issue Service Manual Rev. Order No. TL1001S001V0 Chapter 1: General Infromation 1-1. Table of Contents ......................1 Document control Chapter 1. General Information ................2 ..................1-1. Table of Contents ..................1-2. General Guidelines ..............1-3. Caution and Warning symbols ..............

  • Page 3: General Guidelines

    Issue Service Manual Rev. Order No. TL1001S001V0 1-2. General Guidelines When servicing,observe the original lead dress.If a short circuit is found, replace all parts which are overheated or damaged by the short circuit.After servicing ,see to it that all the protective devices such as insulation barriers ,insulation papers shields are properly installed .Confirm that the screws,parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the service places serviced or not.

  • Page 4: Features

    Issue Service Manual Rev. Order No. TL1001S001V1.1 Chapter 2: General Infromation 2-1 FEATURES Soak wash make cleaner wash. Fashionable appearance, transparent top lid Efficaciously reduce noise Automaticly power off function Self-adjustment to unbalance of laundry in spinning Fuzzy computer control, self-program function, more convenient washing 2-2 Net Dimension Unit:mm...

  • Page 5: Specifications

    Issue Service Manual Rev. Order No. TL1001S001V0 2-2 SPECIFICATIONS HLP24E Model Free standing Built under 7704353033123 EAN code Energy efficiency class Features for use Wash capacity Spin capacity Small/Medium/Large/Super Level/Volume Preset Residual dampness <115 Control model Controller Normal computerized Fuzzy computerized...

  • Page 6: Chapter 3. Safety Precautions

    Service Manual Issue Rev. Order No. TL1001S001V0 Chapter 3. Safety Precautions 3-1. Safety The washing machine must be positioned Please plug the power plug on special so that the plug is accessible. Be sure to pull receptacle. Be sure to use three-pins the plug off and close the water faucet in power receptacle.

  • Page 7: Warning And Cautions

    Issue Service Manual Rev. Order No. TL1001S004V0 3-2.Warning and Cautions Do not decompose, repair or alter the Do not stretch hands into the working machine by yourself. machine. It is dangerous even if the rotation is slow. Take special care of the children.

  • Page 8: Chapter4 Installation And Accessory Parts

    Issue Service Manual Rev. Order No. TL1001S001V1.1 Chapter4 Installation and accessory parts 4-1.Key points in installation Please install and adjust the machine according to the requirement of the mannual. It is very important to your security and correct operating the machine. 4-2.

  • Page 9: Usage Of Operation Buttons

    Issue Service Manual Rev. Order No. TL1001S001V0 4-4.Usage of operation buttons WASH CYCLE BUTTON Use this button to select the desired cycle for your wash load. The standard default settings of each cycle will be displayed; the default settings can be changed by using the Setting button - Water Level. There are 6 cycles to choose from: Heavy Duty - Use this cycle for heavily soiled durable garments.

  • Page 10: Delay Start Button

    Issue Service Manual Rev. Order No. TL1001S003V0 DELAY START BUTTON Press this button to delay the start of your wash cycle between 1 - 24 hours in one hour increments. Use this button to select a delayed start of the washer. The number of hours will be shown in the Estimated Time Remaining Display.

  • Page 11: Product Briefs

    Issue Service Manual Rev. Order No. TL1001S003V1.1 4-5 Product Brief 1)Computer sequencer It adopts pouring seal with polyurethane on the surface. The light-emitting diode is sealed with insulation bushing to avoid humidit y . T o avoid splashing, the surface of computer plate and box and the operation components of the control panel seat are coated with control panel film.

  • Page 12: Key Points In Disassembly

    Issue Se r vice Manual Rev. Model No: TL1001S003V0 Key points in disassembly General attention Be sure to pull off the power plug in disassembly or maintenance Use stipulated crimo terminals in connecting the wires between the conducting wires as far as possible ,and fix with suitable tools ,and insulate with insulation tape completely .

  • Page 13

    Issue vice Manual Rev. Model No: TL1001S003V1.1 Attention : Do not lift the control panel seat by force ,otherwise the safety switch control rod may get transformed.and the jointer part of the connecting pipe of the water level sensor may be loosened ,therefore influence the normal operation of the microswitch and water level sensor .

  • Page 14

    Issue Service Manual Rev. Model No: TL1001S003V0 Chaper5.PARTS AND FUNCTIONS Front Vie w 5. Cab inet Handle (loca ted on bo th 1. Top Lid sidesof thewasher) Control Panel 6.Drain bushing Washer Cab inet Screw co ver Adjustable Leg Back View 8.

  • Page 15: Chapter 6. Maintenance Service And Trouble Shooting

    Issue Service Manual Rev. Order No. TL1001S003V0 Chapter. 6 MAINTENANCE SERVICE AND TROUBLE SHOOTING Phenomena The reason How to settle The digitron displays E0. The top lid is open during Close the top lid. reserve procedure. The drainage cannot Is the drain hose put down ? Put down the drain hose .

  • Page 16: Trouble Shooting Charts

    Issue Service Manual Rev. Order No. TL1001S003V1.1 6-2 Trouble-shooting charts If you replace the computer sequencer without checking the other components carefully , the computer sequencer may be damaged again .Therefore,please first check if the other components working normally before replacing the computer sequencer in maintenance . 6-2-1 No acting (The indicator is off ) Confirm that there is no power failure , and the power plug is inserted reliably.

  • Page 17: No Water Filling

    Service Manual Issue Rev. Order No. TL1001S003V1.1 6-2-2 No water filling Switch on the power .Push the START button Remove the foreign materials of the water There is sound Confirm the action sound inlet valve filter screen or raise the water of the water inlet valve ? pressure to 0.03Mpa-1Mpa before use There is no sound...

  • Page 18: No Draining

    Issue Service Manual Rev. Order No. TL1001S003V1.1 6-2-4 Set rinse or spin start No draining the machine. Roll up normally Check the drain system like the Check if the drain motor acts? drain pump etc. Measure the voltage Exist Check the drain motor. of the two ends of the drain motor.

  • Page 19: No Spinning

    Issue Service Manual Rev. Order No. TL1001S003V1.1 6-2-6 No spinning The washing and draining are normal. No On/Off point Check the On/off point of Replace the microswitch or stop the microswtich and stop switch. switch. Normal Check if the clutch pawl is Replace the drain motor.

  • Page 20: Too Much Noise In Washing

    Issue Service Manual Rev. Order No. TL1001S003V1.1 6-2-8 Too much noise in washing If the noise of the motor Replace the motor. is too much? If the motor fastened tightly? Fasten the motor. The pulsator is rubbing the Add pulsator gasket. bottom of the inner tub 6-2-9.

  • Page 21: Brake Time Out

    Issue Se r vice Manual Re v. Model No: TL1001S003V1.1 6-2-10 9. Brake time out Is the brake moment of the retarder Adjust the brake moment. lower than 6N.m? Is the reset spring of the retarder loose? Adjust the reset spring. Check if the pawl can leave the ratchet for 2mm Is the gap between the connecting arm block and the brake arm of retarder less...

  • Page 22: Chapter 7 Wiring Diagram

    Issue Service Manual Rev. Order No. TL1001S003V0 Chapter 7 WIRING DIAGRAM Fuse Black Black Yellow White Cover Switch Yellow Hote Water Pink Blue Green inlet valve Grey Blue Cold Water inlet valve Red/White White White Stop Switch Red/White Blue Orange Yellow Blue Retractor...

  • Page 23

    Sincere Forever Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com...

Comments to this Manuals

Symbols: 0
Latest comments: