Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZHC 95 ALU
Summary of Contents for Zanussi ZHC 95 ALU
- Page 1 INSTRUCTION BOOKLET COOKER HOOD ZHC 95 ALU...
-
Page 2: Important Safety Information
• It is dangerous to alter the specifications or or serious malfunctioning. Refer to your local modify this product in any way. Zanussi Service Force Centre. Always insist on • When installed between adjoining wall cabinets, genuine spare parts. the cabinets must not overhang the hob. -
Page 3: Table Of Contents
CONTENTS For the User For the Installer Important Safety Information Technical Information Your Appliance Electrical Connections Operating Instructions Installing the Cooker Hood Maintenance and Cleaning Something Not Working Service and Spare Parts Customer Care Department Service Force Centres Guarantee Conditions... -
Page 4: Your Appliance
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after you finish cooking. -
Page 5: Maintenance And Cleaning
MAINTENANCE AND CLEANING Before carrying out any The cooker hood must be kept maintenance or cleaning clean, a build up of grease or fat isolate the cooker hood from can be a fire hazard. the mains supply. Metal grease filters It is necessary to wash these filters at least every two months with warm water to which a little washing up liquid has been added. -
Page 6: Something Not Working
* calls to this number may be recorded for training For general assistance with your appliance or for purposes. information on other Zanussi products please contact our Customer Care Department by letter or telephone at the address shown or visit our website at... -
Page 9: Guarantee Conditions
Standard Guarantee Conditions We, Zanussi, undertake that if within 24 months of the date of the purchase this Zanussi built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials and carriage on condition that: •... -
Page 10: Installation Instructions
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS Height (CANOPY) 100 mm Height (CHIMNEY) 450-850 mm Width (CANOPY) 898 mm Width (CHIMNEY) 200 - 270 mm Depth 507 mm Gross weight 24,5 kg... -
Page 11: Installing The Cooker Hood
INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed The cooker hood is made up of the following it is easily accessible to an engineer in the event components: of a breakdown. 1 No. Canopy C complete with controls and worktop All installation must comply with the local illumination. -
Page 12: Clearance Heights
INSTALLATION INSTRUCTIONS Clearance Heights This appliance can be used in either a ducting or filtering mode. Ducting – Cooking vapours and/or odours are passed The cooker hood is designed to be fitted over a straight outside (ceiling and/or wall) via a disposal cooking appliance at the clearance heights stated, duct, using the holes that are on the top and/or the providing the maximum output of the appliance... - Page 13 INSTALLATION INSTRUCTIONS The versatility of the ducting fan unit on this hood enables it to be installed in one of four different ways: Air outlet directed upwards (re-circulation fitting only). Air outlet directed towards the wall (ducting fitting only). Air outlet directed to the right or left (ducting fitting only).For correct installation of the hood, please proceed in the following stages: •...
- Page 14 INSTALLATION INSTRUCTIONS Installation of the hood canopy C Drilling the wall a) Using the cardboard template provided, mark on the wall the centres of holes 1 for fixing of the hood canopy C .The centre of hole 2 for fixing the chimney, (a) air outlet directed upwards or towards the wall, (b-c) air outlet to the right or left hand side, must be marked at a distance X from the line between holes 1,obtained by measuring the extension Z of the chimney required for installation, plus 18 mm X =Z +25-7.Using a Ø8 mm drill bit, drill the points marked in this way.
- Page 15 INSTALLATION INSTRUCTIONS Fitting the hood canopy C to the wall a) Remove the lower grill and the active charcoal filter if present (see paragraph on maintenance). b) Fit the support rod B using the two screws K (3,5x9,5)provided. c) Hook the hood canopy C to the eye bolts O fixed in holes 1.
- Page 16 INSTALLATION INSTRUCTIONS Drilling the shelves: a) Using the cardboard template provided, and S36_12 taking hole “B ”as a point of reference, drill the shelves along the central axis to allow the passage of the chimney. The chimney must be inserted into the shelves before it is fixed to the hood canopy C.
- Page 17 INSTALLATION INSTRUCTIONS - Remove the plug from the upper part of the ducting fan unit, as it is not possible to insert the flange F with the plug in place. - Fit the flange F Ø120 or 150 mm,replace the plug. ·...
- Page 18 INSTALLATION INSTRUCTIONS Ducting or re-circulation fitting Ducting fitting. This is possible for all forms of installation: a) Connect the air outlet to the external ducting system. b) Remove the activated charcoal filter (if there is one)inside the hood canopy (see Maintenance). Re-circulation fitting This is only possible with the air outlet directed upwards.
- Page 20 © Electrolux Household Appliances Limited 2001 4329478 03 - 010910...