Related Manuals for Hilti AG 500-A18
Summary of Contents for Hilti AG 500-A18
- Page 1 AG 500-A18 Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções...
- Page 2 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado C US...
-
Page 5: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS AG 500-A18 angle grinder 1 These numbers refer to the corresponding illustra- It is essential that the operating instruc- tions. The illustrations can be found on the fold-out tions are read before the power tool is op- cover pages. -
Page 6: Description
The power tool may be used only for dry cutting or grinding. Cutting or grinding materials containing asbestos is not permissible. When grinding stone, a vacuum cleaner equipped with the appropriate filter, e.g. a suitable Hilti vacuum cleaner, must be used. - Page 7 It is recommended that a dust removal system consisting of matched components, i.e. dust removal hood and a suitable Hilti vacuum cleaner, are used for cutting, grinding and slitting work on mineral materials such as concrete or stone. These serve to protect the operator and increase the life of the power tool and disc used.
-
Page 8: Insert Tools, Accessories
It is recommended that a dust removal system consisting of matched components, i.e. dust removal hood and a suitable Hilti vacuum cleaner, are used for cutting, grinding and slitting work on mineral materials such as concrete or stone. These serve to protect the operator and increase the life of the power tool and disc used. -
Page 9: Technical Data
Designation Short designation Description Battery B 18/2.6 Li‑ion Battery B 18/3.3 Li‑Ion Charger for Li-ion batteries C 4/36, C 4/36‑ACS or C 4/36‑ACS TPS Charger for Li-ion batteries C 4/36‑90 Charger for Li-ion batteries C 4/36‑350 4. Technical data Right of technical changes reserved. Power tool AG 500‑A18 Rated voltage... - Page 10 Save all warnings and instructions for future b) Use personal protective equipment. Always reference. The term “power tool” in the warnings wear eye protection. Protective equipment refers to your mains-operated (corded) power such as dust mask, non-skid safety shoes, hard tool or battery-operated (cordless) power tool.
- Page 11 power tool’s operation. If damaged, have the b) Operations such polishing are not recom- power tool repaired before use. Many accidents mended to be performed with this power tool are caused by poorly maintained power tools. Operations for which the power tool was not f) Keep cutting tools sharp and clean.
- Page 12 i) Keep bystanders a safe distance away from Kickback is the result of power tool misuse and/or work area. Anyone entering the work area must incorrect operating procedures or conditions and can wear personal protective equipment. Fragments be avoided by taking proper precautions as given of workpiece or of a broken accessory may fly below.
- Page 13 e) Do not use worn down wheels from larger power 5.2.6 Safety warnings specific for wire brushing tools. Wheel intended for larger power tool is not operations suitable for the higher speed of a smaller tool and a) Be aware that wire bristles are thrown by the may burst.
- Page 14 Have the tool repaired at length of the drive spindle. an authorized Hilti service center right away. h) The workpiece must be fixed securely in place. s) WARNING: Some dust created by grinding, i) Do not use cutting discs for grinding.
-
Page 15: Before Use
NOTE DANGER Battery performance drops at low temperatures. Use Only used the specified Hilti battery packs and Hilti the tool only after fully charging the battery. This battery chargers which are listed under "Acces- ensures that maximum battery capacity is available. - Page 16 Adjust the position of the guard to suit the require- switch interlock activated before fitting the battery. ments of the work being done. Use only the Hilti batteries approved for use with this power tool. 6.7.1 Fitting the guard 5...
- Page 17 6.7.2.1 Fitting the cutting guard 4 6 NOTE The Kwik-Lock nut cannot be used with cup wheels, NOTE brushes, rubber backing pads, tuck pointing discs Take care to ensure that the on / off switch is freely (special discs used for joint repair) or with diamond accessible and operable at all times.
-
Page 18: Operation
7. Operation CAUTION Breathing protection must be worn if the power tool is used without a dust removal system for work that creates dust. WARNING WARNING Wear personal protective equipment. Exposure to Avoid touching rotating parts. Switch the power tool noise can cause hearing loss. -
Page 19: Troubleshooting
Do not operate the tool if parts are damaged or when the controls do not function faultlessly. Have The outer casing of the power tool is made from the power tool repaired by Hilti Service. impact-resistant plastic. Sections of the grip are made from a synthetic rubber material. -
Page 20: Disposal
2.6 Ah. 10. Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 21 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4081 | 0112 | 00-Pos. 3 | 1 Printed in China © 2012 Right of technical and programme changes reserved S. E. & O.
Need help?
Do you have a question about the AG 500-A18 and is the answer not in the manual?
Questions and answers