Panasonic EP3203 Operating Instructions Manual page 12

When you Want More Control over Individual Massage Settings
1. Press .
2. Select and press the User Memory Button you require.
(You can actually press one of the User Program buttons without pressing
3. Select and press the program you desire.
The specific treatment areas you recorded are displayed.
• The massage lounger will carry out body searching to check whether or not someone with the same physical
characteristics is using the unit. (Nothing will be displayed and no sounds will be emitted during this period.)
If the physical characteristics are the same as those recorded the previous time then the massage will start immediately. If,
however, the physical characteristics are determined to be different then body searching will be carried out in the normal
way before the massage begins.
Creating a Customized Program
After following the procedures outlined on this page and the previous page, after the program has
finished and while the button is still flashing press the same User Memory Button. You must press A or
B or C to record any changes made.
Erasing Recorded Data
• It is possible to restore the factory default settings.
(It is not possible to return to the previously recorded User Program setting.)
(1) Press .
(2) Select and press the button with the information you want to erase.
• The button will stop flashing and the Programmed Operation buttons will start flashing.
(3) Hold the same button down (for at least 3 seconds) until
• The button selected will start to flash (for approximately 15 seconds).
(4) Press the same button again while it is flashing.
• The data recorded will be erased and the button will stop flashing.
20
.)
(i.e., shiatsu, deep, gentle, refresh, Self Prog.)
, , and stop flashing.
Additional Information
Detailed Information regarding User Adjustment Functions
(1) What happens when I press ?
• The program will be changed so that the overall amount of time spent on that particular area during the program is
increased.
• The massage action at the time when the button was pressed will first be repeated.
• The massage action at the time when the button was pressed will be increased in that area when that same
massage action is carried out within the massage program.
• The overall time of the massage (approximately 15 minutes) will not be increased.
• This function cannot be used in the Self Program.
(2) What happens when I press ?
• The point where the massage is currently being carried out will be changed slightly.
• This is to ensure that the correct acupressure points can be reached on people with different physical characteristics.
• The button can be pushed once in each direction. This moves the
massage heads approximately 11/16" (1.8 cm) up or down and
approximately 1/4" (0.6 cm) left or right from the center of the pre-
programmed acupressure point.
• The new point will be recorded and whenever that point is massaged
during a program the massage heads will automatically move there.
• The new point is used in all programs.
(The information recorded in each User Memory Button is independent of other User Memory Buttons.)
Massage Point Priority Display
When is pressed or adjustments are made to the user data the results are shown in the
Massage Point Priority Display.
• The amount of time that will be spent on each point during the next massage is displayed.
• The higher the level, the longer the amount of time that will be spent on that point.
• The number of levels is an indication only and is not necessarily an exact indicator of the proportion of
time that will be spent on each point.
Advanced Use of the User Program Function
• Programmed Operations were created by professional massage therapists in accordance with the aim of each
program. While based on these programs, the User Adjustment Functions allow users to modify the massage
parameters. Therefore, it is not possible to focus on one particular area using this function (e.g. the shoulders)
during a single massage. If you want to focus on one particular area then please use the Self Program or the
Manual Operation.
What Kind of Data Can Be Recorded?
Recordable Data
• The five Programmed Operations can be recorded in each of the User Adjustment Functions buttons.
(The massage actions of Programmed Operations. The data from the previous Self Program.)
• Data regarding physical characteristics.
(When the User Adjustment Functions button is pressed and the massage begins, body searching is carried out in
accordance with this data and if that data matches then the massage begins. If it does not match then body
searching is carried out again.).
The following are not recorded as part of the User Adjustment Functions:
• Data regarding Manual Operations.
• Massage lounger position (reclining angle and legrest angle).
• Data regarding the leg/calf massage.
• When Manual Operation has been selected during a Programmed Operation.
• Massage strength settings in the Programmed Operations.
• When the massage has been stopped by pressing
Acupressure
Approx. 11/16" (1.8 cm)
Points
Approx. 1/4" Approx. 1/4"
(0.6 cm) (0.6 cm)
Approx. 11/16" (1.8 cm)
and the massage terminated.
21