Weed Eater WELRVBA Owner's Manual page 12

The op er a tion of any riding mower can result in foreign objects thrown
into the eyes, which can result in severe eye dam age. Al ways wear
safety glass es or eye shields while op er at ing your riding mower or
per form ing any ad just ments or repairs. We rec om mend a wide vi sion
safe ty mask over spec ta cles or stan dard safety glass es.
00155
HOW TO USE YOUR RIDING
MOWER
TO SET PARKING BRAKE
Your riding mower is equipped with an opera-
tor presence sens ing switch. When engine
is running, any attempt by the op er a tor to
leave the seat without first setting the parking
brake will shut off the engine.
1. Depress brake pedal all the way down
and hold.
2. Pull parking brake lever up and hold,
release pressure from brake pedal, then
release parking brake lever. Pedal should
remain in brake position. Ensure parking
brake will hold mower secure.
STOPPING
MOWER BLADE -
• To stop mower blade, move deck clutch
lever to disengaged po si tion.
( ) )
(
Deck Clutch
Deck Clutch
Control Control
"Engaged" "Dis en gaged"
GROUND DRIVE -
• To stop ground drive, depress brake pedal
all the way down.
• Move motion control lever to neutral posi-
tion.
Motion Control Lever
ENGINE -
• Move throttle control between half and full
speed (fast) position.
NOTE: Failure to move throttle control be-
tween half and full speed (fast) position, be-
fore stopping, may cause engine to "backfire".
Throttle
• Turn ignition key to "STOP" position and
remove key. Always remove key when
leaving riding mower to prevent un au tho r-
ized use.
IMPORTANT: Leaving the ignition switch in
any position other than "STOP" will cause
the battery to discharge and go dead.
NOTE: Under certain conditions when riding
mower is standing idle with the engine run-
ning, hot engine exhaust gases may cause
"browning" of grass. To eliminate this pos-
sibility, always stop engine when stopping
riding mower on grass areas.
CAUTION: Always stop riding mower
com plete ly, as described above, before
leav ing the operator's position.
12
RIDING MOWER
CHASSIS
KEY PART
NO. NO. DESCRIPTION
1 532 43 61-76 WELDMENT, CHASSIS
2 532 18 01-66 BRACKET, SEAT
7 532 43 61-77 PLATE, ENGINE
8 532 43 68-60 BRACKET, CHASSIS FRONT
10 532 44 18-05 PAN, SEAT
11 532 19 93-70 BRACKET, SWITCH MOUNTING
13 532 43 65-95 COVER, FOOT REST
14 532 43 65-92 STRUCTURE, FOOT REST
15 532 44 20-69 SUPPORT, FOOT REST
16 532 43 94-01 PANEL ASM, CONTROL
18 – – – – – – ENGINE, 215807-1529-G1
(439273) (NON-CALIFORNIA)
(ORDER PARTS FROM
ENGINE MANUFACTURER)
19 532 43 68-61 KEEPER, BELT
22 532 44 21-30 DECK CLUTCH ASM
23 532 14 98-46 KNOB
25 872 14 04-24 BOLT
26 873 51 04-00 NUT, 1/4-20
29 532 43 89-21 BOLT, 7/16-20 X 1.00
32 817 06 06-20 SCREW 3/8-16 X 1-1/4
33 532 12 41-81 SPRING, SEAT
34 532 12 37-40 SPRING
35 872 05 04-12 BOLT, 1/4-20 X 1 1/2
39 532 13 43-00 SPACER
40 532 12 12-48 BUSHING, NYLON SNAP
41 532 12 39-76 NUT, LOCK
42 532 17 18-52 BOLT, 5/16-18 SHOULDER
43 873 80 05-00 NUT, 5/16-18
44 532 43 66-12 SEAT
45 817 00 05-12 BOLT, 5/16-18 X 3/4
51 532 42 88-56 BRACKET
52 532 14 50-06 CLIP PUSH-IN HINGED
53 532 43 85-62 SCREW
54 532 43 64-73 DISC FRICTION
55 532 43 58-08 TORSION BODY UPPER
56 532 44 19-25 TORQUE ASM CONTROL
LOWER
57 532 43 64-79 SPRING HELIX
59 819 18 24-11 WASHER 9/16ID X1 1/2OD 11G
ZIN
60 532 43 78-56 FUEL TANK ASM
62 532 40 04-14 FUEL LINE
63 532 41 41-19 PURGE LINE
MODEL NUMBER WELRVBA (96026000100)
PRODUCT NUMBER 960 26 00-01
KEY PART
NO. NO. DESCRIPTION
64 532 12 34-87 CLAMP HOSE
65 532 43 85-96 FUEL CAP
66 532 43 66-06 FUEL TANK SUPPORT BRKT
67 532 42 17-56 SCREW #10 X 0.500
68 532 43 98-51 SHIELD HEAT
69 532 43 74-27 BRACKET MOUNT CABLE
70 532 44 20-68 CONSOLE CENTER
CUPHOLDER
71 532 43 78-57 THROTTLE ASM
72 532 19 51-61 STUD FASTNER
73 873 90 05-00 NUT LOCK HEX FLANGE 5/16-
18
76 877 10 08-12 PIN CLEVIS
77 876 02 02-08 PIN COTTER 1/16 X 1/2
78 532 43 70-56 BRACKET SUPPORT ROD
79 532 43 70-57 BRAKE WELDMENT
80 532 42 96-93 BRAKE PEDAL COVER
81 532 43 73-74 WELDMENT LINK CONNECTING
82 532 16 94-84 RETAINER CLIP
83 532 43 93-68 STEERING BOOT REAR
84 532 43 92-91 STEERING BOOT FRONT
85 532 43 76-60 PARKING BRAKE HANDLE
86 532 43 87-62 ACTUATOR PARKING BRAKE
87 532 16 54-92 SHOULDER BOLT
88 532 42 81-10 CROSS BRACE
91 532 43 74-01 TRACK CLUTCH BRKT
94 874 49 05-48 BOLT
95 532 43 67-02 BRACKET
97 532 43 64-72 PULLEY ENGINE
98 817 49 04-08 SCREW 1/4-20 X 1/2
104 818 10 10-08 SCREW #10-14 X 1/2
105 532 44 21-34 ENGINE COVER
106 532 43 68-34 STRAP BATTERY
108 532 43 71-68 COVER REAR TRANSAXLE
109 532 43 90-08 RETAINER BRAKE
110 532 42 21-45 CONTROL HINGE PIN
111 532 43 81-71 SHIELD, BRAKE CABLE
112 817 72 04-08 SCREW THD CUT
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
33