HPS500/1000 OM 10/25/99 2:40 PM ABLE OF ONTENTS Page 2 Caution...3 Important Safety Instructions...4 Introduction...5 About This Product...5 Unpacking the Subwoofer...5 A Few Suggestions ...5 Volume Control ...5 Positioning...6–7 Identification of Front Panel Control ...8 Controls...8 Connecting Your Subwoofer ...9–11 Operation ...12 Set Controls ...12 Power On ...12...
DO NOT REMOVE COVER (0R BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL THIS INFINITY PRODUCT IS DESIGNED FOR 120-VOLT USE ONLY! FOR DETAILED SAFETY PRECAUTIONS, PLEASE SEE FOLLOWING PAGE IN THIS OWNER ’ S MANUAL FOR “IMPORTANT SAFETY INSTRUCTIONS.”...
HPS500/1000 OM 10/25/99 2:40 PM 1) Read Instructions – All the safety and operating instructions should be read before the product is oper- ated. 2) Retain Instructions – The safety and operating instructions should be retained for future reference. 3) Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
Page 5 NTRODUCTION Infinity’ s HPS-500 and HPS-1000 subwoofers have been designed to enhance the bass frequencie of any audio system. Both subwoofers may be used with speakers of any size. Obviously, th greatest bass enhancement will be achieved when the subwoofer is connected to speakers that d not have the capability to create deep bass.
Should you have questions relating to your installation, it is advisabl to call either your dealer or Infinity’ s Customer Service Department for advice. The performance of the subwoofer is directly related to its placement in the listening room an how you align the subwoofer with its satellite speakers.
Page 7
As a starting point, initially place the subwoofe behind your right-channel satellite speaker, six inches from the wall. We suggest trying this loca tion first because, in an orchestra, the bass instruments are usually located in the back and to th right (see Figure 1).
2. Crossover: Controls the frequency below which the subwoofer will begin working. 3. Phase: Reverse/normal switch changes audio-signal polarity. 4. Gain: Controls subwoofer volume level. 5. Input: Switches between the normal line/speaker inputs and the direct-LFE input. Figure 2. 0˚...
HPS500/1000 OM 10/25/99 2:40 PM Page 9 ONNECTING UBWOOFER If your receiver/processor does not have subwoofer outputs for the left and right channel — — — — B-LINK ™ OUTPUTS INPUTS...
Page 10
HPS500/1000 OM 10/25/99 2:40 PM NOTE: Some receivers have a single subwoofer output (do not confuse this with a single LFE output as described below). In that case, it is recommended that you use a Y connector (not included) to maximize performance. NOTE: In this case, you do not need to use a Y connector.
Page 11
HIGHPASS OUTPUT 120Hz 160Hz 80Hz RECEIVER/AMPLIFIER OR PROCESSOR/AMPLIFIER LEFT RIGHT LEVEL LEVEL MAIN RIGHT LOUDSPEAKER MAIN SPEAKER OUTPUT RIGHT LEFT LEFT LOUDSPEAKER...
(Figure 2) up to the “5” position (half way). If no soun (Figure 2) until you obtain a pleasing blend of bass. Bas (Figure 2) – The Low-Pass control determines the highest frequenc (Figure 2) determines whether the subwoofer speaker’ s piston-lik...
This may indicate an unbalanced condition in your system (too much bass), that th system is in an especially large room, or that speaker placement may be incorrect. Try sever other locations before concluding that the Volume control must be set at maximum.
If everything seems to be in good working order and the subwoofer still malfunction DO NOT ATTEMPT ANY REPAIRS! Contact your Infinity dealer and get the name of th authorized Infinity service center near you. If there is no facility near you, contact Infinity Customer Service Department at (800) 553-3332, or write: Infinity Systems, Inc.
Need help?
Do you have a question about the HPS-1000 and is the answer not in the manual?
Questions and answers