Table of Contents
Advertisement
a. Vacuum thoroughly - For carpet, use
a HOOVER vacuum cleaner with an agi-
tator for best results. Vacuum upholstery
tool attachments. Use a crevice tool to
reach Into tufts and folds. Do not use
the 'SteamVac' deep cleaner as a dry
vacuum cleaner.
b. For upholstery, check cleaning
code - Use your HOOVER 'SteamVac'
'Widepath' deep cleaner only if the
upholstery fabric is marked with a "w"
(for "wet" clean) or "SW (for
"solvent/dry" or "wet" clean). Do not
clean fabric marked "S" ("solvent/dry"
clean only). If your upholstery does not
have a code, seek professional assis-
tance.
and water according to the instructions
a. Allow carpet or upholstery to dry. To
help prevent matting and resoiling the
carpet, keep children and pets away
from surface until it is completely dry. If
it is necessary to walk on damp car-
pet, place towels or white cloths on the
traffic areas.
If furniture must be replaced before the
carpet is dry, place plastic or aluminum
foil under legs of furniture so metal
slides or wood finishes will not stain the
e. Remove lint from filter screen located
on bottom of cleaner as follows.
When brushes seem to be rotating
slowly, disconnect deep cleaner from
this screen.
Tilt cleaner back so handle rests on floor.
Squeeze frame, lift and pull it out. Wipe
off screen and push frame back into
place
under "Fill clean solution tank", Figs. 2-8 to
solution. In a small, hidden area, gently rub
the surface with the dampened cloth. Wait
ten minutes and check for color removal or
bleed with white paper towel or cloth. If sur-
face has more than one color, check all col-
ors.
d. When cleaning entire floor, move
furniture out of area to be cleaned
(may not be necessary if only high traffic
areas are to be cleaned). For furniture
too heavy to move, place aluminum foil
or wax paper under legs. This will pre-
vent wood finishes from staining carpet.
Pin up furniture skirts and draperies.
e. Pretreat spots and heavy traffic
areas with HOOVER@ PreCleaner-
Test PreCleaner for colorfastness by first
spraying it on a hidden area; wait ten
minutes and blot with white paper towels
or cloth.
If no color change is visible, spray
PreCleaner onto spots and traffic areas.
Wait at least ten minutes. Use your
'SteamVac' 'Widepath' deep cleaner to pick
up PreCleaner and spot. Repeat until spot
is removed; carefully scrub with a house-
hold scrub brush if necessary
b. If desired, the carpet may be rinsed.
Rinsing is not necessary for cleaning,
but it may improve the surface's appear-
ance after it is dry.
If rinsing is desired, be careful not to
over-wet the carpet or upholstery.
Allow time for carpet or upholstery to
dry completely between cleaning and
rinsing. To rinse, follow the same proce-
dure for cleaning only using hot tap
water with no detergent in the upper
clean solution tank.
c. Empty tanks, rinse with clear water
and let air dry. Rinse the solution tank
cap and recovery tank lid and let air dry.
Return cleaner to upright position.
f. If desired, vacuum thoroughly after
carpet has completely dried. This will
help reduce any shading left by the
deep cleaner's brushes.
If lint or other debris becomes lodged in
nozzle, do not attempt to remove
nozzle cover.
Pour one to two cups of clear water on a
non-carpeted floor. Do not pour water
Note:
onto a wood floor.
Pick up the water with your deep clean-
er. Repeat as necessary until debris Ls
flushed out of nozzle.
Do not saturate carpet or upholstery with
PreCleaner.
If you do not have access to the
PreCleaner Spray, double the amount
of HOOVER Detergent (use 2 capfuls
or 10 oz. per 1 gallon) in the clean
solution tank.
No cleaning solution removes all stains from
all carpets. Stain removal varies with the
type of spill, time elapsed before removal.
carpet material, and carpet type
f.To prevent staining, use plastic or alu-
minum foil to protect wood or metal sur-
faces from possible water spray
g. To avoid wetting and possible damage
to wood floors underneath area rugs/car-
pet, either move area rugs/ carpet to a non-
wood bare floor surface or place waterproof
material (e.g. plastic) underneath them
before cleaning.
See pages lo-13 for instructions on various
cleaning tasks.
d. Remove lint from filter screen located
inside recovery tank.
To clean the outside of the machlne,
wipe off dirt with a cloth dampened In
warm water and mild detergent. Do not
use solvent or petroleum based prod-
Hide quick links:
Advertisement
Table of Contents
