Hilti DD EC-1 Operating Instructions Manual
Diamond core drilling machine
Hide thumbs
Also See for DD EC-1:
- Operating instructions manual (17 pages) ,
- Operating instructions manual (74 pages) ,
- Operating instructions manual (39 pages)
Subscribe to Our Youtube Channel
Related Manuals for Hilti DD EC-1
Summary of Contents for Hilti DD EC-1
- Page 1 DD EC-1 Operating instructions Mode d’emploi Manual de instrucciones Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
- Page 2 DD EC-1 Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
- Page 3 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
- Page 4 DD EC-1 DD EC-1 Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
- Page 5 DD EC-1 DD EC-1 > 0.5 mm 0,5mm ″ > DD EC-1 DD EC-1 DD EC-1 Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
- Page 6 Pos. 1 Pos. 2 DD EC-1 Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
-
Page 7: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS DD EC-1 diamond core drilling machine In these operating instructions, this symbol indi- It is essential that the operating cates points of particular importance to safety. The instructions at these points must always be observed instructions are read before the in order to reduce risk of serious injury. -
Page 8: General Safety Rules
General safety rules 4.2 Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, 1. WARNING! jewelry, or long hair can be caught in moving parts. Read and understand all instructions. -
Page 9: Specific Safety Rules And Symbols
According- ly, if necessary, have the tool repaired at a Hilti service Drilling through reinforcing bars center or authorized Hilti repair workshop. -
Page 10: Description
......volts Description ......alternating current ......hertz The DD EC-1 is an electrically-powered diamond core ......watts drilling machine for wet drilling......amperes Items supplied: The following items are supplied: electric ......no load speed tool, water collector holder including water collector, ...... -
Page 11: Main Features Of The Tool
Main features of the tool The position and dimensions of the holes drilled must be approved by the design engineer, architect or person in charge of the building project (building statics). – Drilling machine with TOPSPIN kinematics, i.e. delib- erate orbital movement of the core bit and chuck –... -
Page 12: Assembly
If the indicator continues to light, further operation of housing the machine ist not permissible. Have the machine repair - ed by a qualified specialist using genuine Hilti spare parts. Inserting the core bit – After the test, switch on the GFCI again by pressing -DANGER- the ON button. - Page 13 – The water recycling unit continues to run for a few – Before beginning drilling, adjust the flow control knob seconds after switching off the DD EC-1. Keep the to the middle position of its range. water collector pressed against the base material –...
-
Page 14: Care And Maintenance
For safety reasons and for optimum transmission of the TOPSPIN action, only DD-C core bits may be used with the DD EC-1. When drilling using special core bits with an effective core depth of 24″, the hole must be pre- drilled using a shorter core bit and water collector. -
Page 15: Disposal
Additional claims are excluded, unless stringent national rules prohibit such exclusion. In particular, Hilti is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inabil- ity to use the tool for any purpose. -
Page 16: Troubleshooting
Water leaks from the gear Water swivel shaft seal defective The machine should be repaired at a Hilti housing service center. The core bit cannot be inserted Chuck operating lever not fully Open the lever as far as it will go. - Page 17 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2518 | 1013 | 0,6-Pos. 3 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 337335 / A3 Printed: 02.12.2013 | Doc-Nr: PUB / 5163253 / 000 / 01...
Need help?
Do you have a question about the DD EC-1 and is the answer not in the manual?
Questions and answers