Hilti UH 700 Operating Instructions Manual
Hammer drill
Hide thumbs
Also See for UH 700:
- Operating instructions manual (18 pages) ,
- Operating instructions manual (53 pages) ,
- Manual (57 pages)
Related Manuals for Hilti UH 700
Summary of Contents for Hilti UH 700
- Page 1 UH 700 Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 07.07.2013 | Doc-Nr: PUB / 5138090 / 000 / 00...
- Page 2 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado Printed: 07.07.2013 | Doc-Nr: PUB / 5138090 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5138090 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5138090 / 000 / 00...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the UH 700 hammer drill. gether with the power tool. Operating controls and parts 1 Ensure that the operating instructions are... -
Page 6: Description
To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 7 Recommended ment mortar, tile adhesive and plas- TE‑MP 110 Recommended ter with mixing paddles 2.6 Items supplied as standard Power tool with side handle Depth gauge Dust shield Chuck key (with keyed chuck) Operating instructions Hilti toolbox or cardboard box...
-
Page 8: Accessories
Chuck key (with keyed chuck) 274081 Dust removal system TE DRS‑S 340602 4 Technical data Right of technical changes reserved. Power tool UH 700 Rated voltage 120 V Rated current input 8.0 A Mains frequency 50…60 Hz Weight of tool without side handle 2.4 kg (5.2 lbs) -
Page 9: Safety Instructions
Power tool UH 700 Speed control Electronic, by way of the control switch Forward / reverse Switching lever with interlock to prevent switching while running Tightening torque when changing the chuck 120 Nm (89 lb/ft) Information about the power tool and its applications... - Page 10 Improve the blood circulation in your fingers by Hilti Customer Service. Check extension cords relaxing your hands and exercising your fingers at regular intervals and replace them if found to during breaks between working.
-
Page 11: Before Use
Release the side handle clamping band by turning the handle counterclockwise. 6.2 Use of extension cords and generators or CAUTION With the UH 700 it is essential to ensure transformers that the sleeve is fitted in the grip section of the side handle. -
Page 12: Operation
7 Operation NOTE The keyless chuck may have to be rotated slightly by hand before the built-in drive spindle lock engages. NOTE DANGER Depending on the type of chuck fitted, either the broad Use auxiliary handle(s), if supplied with the tool. Loss adjusting ring or the rear gripping ring on the chuck must of control can cause personal injury. - Page 13 Remove the chuck key. Position the power tool and drill bit at the point where the hole is to be drilled. 7.2.3 Possible applications Press the control switch slowly (drill at a low speed until the drill bit centers itself in the hole). CAUTION Press the control switch fully to continue working at In accordance with the applications for which it is de-...
-
Page 14: Care And Maintenance
Do not use clean- damaged or when the controls do not function faultlessly. ing agents which contain silicone. If necessary, the power tool should be repaired by Hilti Service. The outer casing of the power tool is made from impact- resistant plastic. -
Page 15: Troubleshooting
Retighten the chuck. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. - Page 16 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3242 | 0313 | 00-Pos. 3 | 1 Printed in China © 2013 Right of technical and programme changes reserved S. E. & O 273762 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5138090 / 000 / 00...