Hilti UH 700 Operating Instructions Manual
Hammer drill
Hide thumbs
Also See for UH 700:
- Operating instructions manual (16 pages) ,
- Operating instructions manual (53 pages) ,
- Manual (57 pages)
Table of Contents
Advertisement
Quick Links
Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00
UH 700
Bedienungsanleitung
Operating instructions
Mode d'emploi
Manual de instrucciones
Istruzioni d'uso
Gebruiksaanwijzing
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Manual de instruções
Οδηγιες χρησεως
Instrukcja obsługi
Инструкция по зксплуатации
de
en
fr
es
it
nl
da
no
sv
fi
pt
el
pl
ru
ja
Advertisement
Table of Contents
Related Manuals for Hilti UH 700
Summary of Contents for Hilti UH 700
- Page 1 UH 700 Bedienungsanleitung Operating instructions Mode d’emploi Manual de instrucciones Istruzioni d’uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Οδηγιες χρησεως Instrukcja obsługi Инструкция по зксплуатации Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00...
- Page 2 Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the UH 700 hammer drill. gether with the power tool. Operating controls and parts 1 Ensure that the operating instructions are... -
Page 6: Description
To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 7 TE‑MP 80 Recommended cement mortar, tile adhesive and TE‑MP 110 Recommended plaster with mixing paddles 2.7 Items supplied as standard Power tool with side handle Depth gauge Dust shield Chuck key (with keyed chuck) Operating instructions Hilti toolbox or cardboard box...
-
Page 8: Accessories
7.5 A 6.9 A 3.5 A 3.1 A 3.1 A input Power tool UH 700 Mains frequency 50…60 Hz Weight of tool without side handle 2.4 kg Weight in accordance with EPTA procedure 01/2003 2.6 kg Dimensions (L x W x H) -
Page 9: Safety Instructions
Power tool UH 700 Speed in 1st gear under no load 900/min Speed in 2nd gear under no load 2,500/min Hammering speed 40,000/min Chuck ∅ 1.5…13 mm Maximum torque, 1st gear 80 Nm Maximum torque, 2nd gear 29 Nm Speed control... - Page 10 b) Avoid body contact with earthed or grounded controlled with the switch is dangerous and must be surfaces, such as pipes, radiators, ranges and repaired. refrigerators. There is an increased risk of electric c) Disconnect the plug from the power source shock if your body is earthed or grounded.
- Page 11 Contact with or inhalation of the dust may should be checked at regular intervals at a Hilti cause allergic reactions and/or respiratory diseases Service Center. Under unfavorable circumstances, to the operator or bystanders.
-
Page 12: Before Use
Release the side handle clamping band by turning the handle counterclockwise. 6.2 Use of extension cords and generators or CAUTION With the UH 700 it is essential to ensure transformers that the sleeve is fitted in the grip section of the side handle. - Page 13 7.2 Operation NOTE Use the key supplied to open the chuck and to tighten it after inserting a tool. 7.2.2.1 Opening the key chuck 6 Insert the chuck key in one of the three holes CAUTION provided in the chuck. Working on the material may cause it to splinter.
- Page 14 Press the control switch slowly (drill at a low speed Press the control switch slowly until the screw grips until the drill bit centers itself in the hole). and is guided by the material into which it is being Press the control switch fully to continue working at driven.
-
Page 15: Care And Maintenance
Do not use clean- damaged or when the controls do not function faultlessly. ing agents which contain silicone. If necessary, the power tool should be repaired by Hilti Service. The outer casing of the power tool is made from impact- resistant plastic. -
Page 16: Disposal
Retighten the chuck. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. -
Page 17: Ec Declaration Of Conformity (Original)
We declare, on our sole responsibility, that this product Deutschland complies with the following directives and standards: 2004/108/EC, 2006/42/EC, 2011/65/EU, EN ISO 12100, EN 60745‑1, EN 60745‑2‑1. Hilti Corporation, Feldkircherstrasse 100, FL‑9494 Schaan Paolo Luccini Jan Doongaji Head of BA Quality and Process Man-... - Page 18 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3242 | 0313 | 00-Pos. 1 | 1 Printed in China © 2013 Right of technical and programme changes reserved S. E. & O 273761 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5138076 / 000 / 00...