Ellington E-SBF58AN5LKRCR2 Installation Manual
  1. Manuals
  2. Brands
  3. Ellington Manuals
  4. Fan
  5. E-SBF58AN5LKRCR2
  6. Installation manual

Ellington E-SBF58AN5LKRCR2 Installation Manual

Fans
Hide thumbs
Table of Contents

Advertisement

Quick Links

Federal regulations require all ceiling
fans with light kits manufactured or
imported after January 1, 2009, to limit
total wattage consumed by the light kit
to 190W. Therefore, this fan is equipped
with a wattage limiting device.
Installation Guide
For Model:
E-SBF58AN5LKRCR2
E192641
net weight of fan: 26.46 lb. (12 kg)
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE

Table of Contents:

Wiring. pg. 5
Warranty. pg. 10
PRINTED IN CHINA

Advertisement

Table of Contents
loading

Related Manuals for Ellington E-SBF58AN5LKRCR2

Summary of Contents for Ellington E-SBF58AN5LKRCR2

  • Page 1: Table Of Contents

    190W. Therefore, this fan is equipped with a wattage limiting device. Installation Guide For Model: E-SBF58AN5LKRCR2 Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation.

  • Page 2: Safety Tips

    SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.

  • Page 3: Unpacking Your Fan

    1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.

  • Page 4: Installation Preparation

    3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet (76cm) that the hanging location allows the blades a (2.13m) clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. 12ft.

  • Page 5: Fan Assembly. Pgs

    5. Fan Assembly. set screw hole If you wish to extend the hanging length of your set screw fan, you must remove the hanging ball from the stop pin 6in. downrod provided to use with an extended downrod (sold separately). [If you wish to use the 6in.

  • Page 6: Wiring

    5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket tab hanging bracket and let hanging ball rest on the hanging bracket.

  • Page 7: Canopy Assembly

    7. Canopy Assembly. antenna Locate 2 screws on underside of hanging receiver bracket and remove screw closest to the open hanging bracket end of of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy screw over loosened screw in hanging bracket and push up.

  • Page 8: Light Kit Assembly

    9. Light Kit Assembly. Remove 1 screw from the fitter plate on the underside of the motor and partially loosen the motor other 2 screws. Align the slotted holes in the housing shade fitter with the loosened screws in the fitter plate, making sure that molex connections come through the hole in the middle of the shade fitter.

  • Page 9: Automated Learning Process./Activating Code

    10. Automated Learning Process./Activating Code. CAUTION: The remote control transmitter can be TRANSMITTER code (back) programmed to multiple receivers or fans. If this is not switches desired, turn wall switch off to any other programmable receiver or fan. This remote control transmitter is equipped with 16 code combinations to prevent possible interference from or to other remote units such as garage door openers, car alarms or security systems.

  • Page 10: Remote Control Operation

    11. Remote Control Operation. HI button - turns fan to HIGH speed MED button - turns fan to MEDIUM speed LOW button - turns fan to LOW speed OFF button - turns fan OFF REV button - used to REVERSE blade direction (fan must be turned low before reversing blade direction) button - pushing button turns light ON/OFF;...

  • Page 11: Troubleshooting

    Return fan, shipping prepaid, to 3. Verify that receiver is wired properly. Craftmade/Ellington. We will repair or ship you a 4. Verify that fan is wired properly. replacement fan, and we will pay the return shipping cost.

Table of Contents