Backlight; Dive.main; Chrono.status; Dive.alt - Aeris F11 Operating Manual

DIVE MODE
Prior to the first dive of a new series, if Wet Activation is set Off, Dive Mode will not activate during operation in any Watch Mode.
It must to be in FREE Mode prior to activating Dive Mode.
If Wet Activation is set On, Dive Mode will activate from any operating surface mode including Watch modes when it senses the
DSD (Dive Start Depth) set for 5 seconds.
Once the first dive of a series is completed, repetitive dives will be activated regardless of what surface operating mode it is in.
Dives start upon descent to the DSD (Dive Start Depth) set (2, 4, or 6 FT; or 0.6, 1.2, or 1.8 M) for 1 second and end upon ascent
to a Depth < 2 FT (0.6 M)** for the BDSI (Between Dive Surface Interval) time set, thus descending before the BDSI time elapses is
the same dive and descending at => the BDSI is a new repetitive dive.
**Upon ascent to < 2 FT (0.6 M), the Dive Main will display 0 FT (0.0 M) until you surface, or descent is made to the DSD
set during the BDSI.

backlight

• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
> If Auto Glo is set On, the Backlight will turn On upon descent to the DSD set and remain on until you surface and the BDSI time
set has elapsed.
When Alarms strike, the Backlight will come On, if Off, and remain On until it is turned Off by L (< 2 sec), or it turns Off automati-
cally after 10 seconds. If it is already On, it will remain On for 10 seconds from the time that the Alarm strikes unless you turn it Off
during that 10 second time.
DIVE MAIN, information includes (Fig. 62A/B):
> CDT (Countdown Timer, min:sec) with min_sec and CDT icons, if set On. Blank if Off.
> Current Depth with FT (or M) icon. 0 FT (0.0 M) when on the surface during the BDSI time set (Fig. 63).
> Elapsed Dive Time (min:sec) with DIVE and min_sec icons.
• A (< 2 sec) - to access ALT.
• S (< 2 sec) - to start/stop the CDT. If set for Auto, the countdown will repeat each time it counts down to 0:00.
• S (2 sec) - to reset the CDT to the time (min:sec) set.
• M (< 2 sec) - to replace the Dive Main with Chrono (Run Timer) Status which will remain on display until S (2 sec) to replace
Chrono with the Dive Main.
CHRONO STATUS, information includes (Fig. 64):
When the Chrono is displayed, it will remain on the display until M (< 2 sec) to replace it with the Dive Main.
> Graphic CHRO with min_sec icons.
> Elapsed run time counting up to 199:59_99 (min:sec_ .01 sec).
> Graphic LAP1 (up to 9).
• S (< 2 sec) - to start the Timer which counts up from 0:00_00 (min:sec_ .01 sec) in increments of .01 sec. After the first 4.99
seconds, the .01 sec digits display 2 dashes ( - - ).
• S (< 2 sec) - to save Lap 1's time and display the graphic LAP2 with the Timer continuing to count up. Total Run Time is always
displayed until stopped.
• S (< 2 sec) - to save/display other Laps up to # 9.
>> After 9 Laps, subsequent Laps continue to be recorded with the earliest being discarded, starting with #1.
>> If the Chrono continues to run and total time reaches 199:59_99, it will Stop and record that as a Lap. Subsequent presses
of S then to have no effect.
• A (< 2 sec) - to stop the Timer, save the lap in progress (the final lap) and total elapsed run time*, then recall Lap 1, displaying
the graphic LAP1 flashing and the Lap 1 time.
*Total elapsed run time is the entire time from S (< 2 sec) that first started Lap 1 until A (< 2 sec) that stopped the timer and
final lap.
>> Subsequent presses of A (< 2 sec) will recall the other Laps.
>> When Laps are recalled, the .01 sec numerics are displayed.
• A (2 sec) - to Reset the Timer to 0:00_00 (Fig. 65).
• M (< 2 sec) - to replace the Chrono screen with the Dive Main, the Chrono will continue in the background if running.
DIVE ALT, information includes (Fig. 66):
> Day of the Week graphic (MON, TUE, etc.).
> Time of Day (hr:min_sec) with AM (or PM) icon.
> Temperature with °F (or °C).
• A (< 2 sec) - to revert to Dive Main.
• Revert to Dive Main after 10 seconds if A is not pressed.
© 2002 Design, 2013 25
F11 OPERATING MANUAL
Fig. 62A - DIVE MAIN
(CDT OFF)
Fig. 62B - DIVE MAIN
(CDT ON)
Fig. 63 - DIVE MAIN
(on surface < BDSI set)
Fig. 64 - CHRONO
(On, running)
Fig. 65 - CHRONO
(reset)
Fig. 66 - DIVE ALT
Doc. No. 12-7285-r01 (5/3/13)