Related Manuals for Hilti DD 350
Summary of Contents for Hilti DD 350
- Page 1 DD 350/ DD 500 Operating instructions Mode d’emploi Manual de instrucciones Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...
- Page 2 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...
- Page 3 4 / 6 9 11 Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...
- Page 4 2 / 4 2 / 4 Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...
- Page 5 3/4/6 Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...
-
Page 6: Table Of Contents
) Gear selector Water flow indicator + Water flow regulator L Water flow indicator § Chuck Water collector system / Supply cord with GFCI (DD 350)/supply cord Ö Water collector holder (DD 500) Ä Water collector : Carrying grips (2x) † Seal ·... - Page 7 Keep these pages open while studying the oper- ing instructions before use. ating instructions. In these operating instructions, the designation “the machine” refers to the DD 350 or DD 500 core drilling /min machine. Amps Volts Watts Hertz...
-
Page 8: General Safety Rules
2. General safety rules WARNING! Read and understand all instructions. c) Avoid accidental starting. Be sure switch is off Failure to follow all instructions listed below may before plugging in. Carrying tools with your fin- result in electric shock, fire and/or serious personal ger on the switch or plugging in tools that have injury. -
Page 9: Specific Safety Rules And Symbols
WARNING: Some dust created by grinding, sand- intended could result in a hazardous situation. ing, cutting and drilling contains chemicals known f) Use only the genuine Hilti accessories or ancil- to cause cancer, birth defects or other reproductive lary equipment listed in the operating instruc- harm, or serious and permanent respiratory or tions. - Page 10 Damaged or faulty switches must be replaced at (e.g. during breaks between working), before a Hilti service center. Do not use the machine if making adjustments, before carrying out care it cannot be switched on and off correctly.
-
Page 11: Functional Description
4.1 Use of the equipment as intended tions concerning operation, care and maintenance. The DD 350 or DD 500 with the DD HD-30 drill stand, Observe the safety precautions and operating instruc- form drilling rigs designed for wet core drilling in min- tions for the accessories used. -
Page 12: Assembly
Under certain conditions it may be necessary to use an alternative fastening method. Please contact Hilti Technical Service if you have any questions about secure fastening. 1. Set the anchor, of a type suitable for the material on which you are working, ideally at a distance of 330 mm (13") - Page 13 tate access. This part, however, must be refitted and fas- 11. Once the drill stand has been positioned correctly, tened securely to the column before operating the machine. remove your finger from the vacuum release valve and press the base plate against the work surface. 7.
- Page 14 1. Lock the carriage in position on the column (activate 5.1.12 Fitting a diamond core bit (machine with the carriage locking mechanism). Hilti BL chuck) 2. Pull out the machine locking bolt. 3. Fit the machine onto the carriage or spacer.
-
Page 15: Operation
Have the machine repair - -CAUTION- ed by a qualified specialist using genuine Hilti spare parts. The core drilling operation may cause hazardous frag- ments to fly off. Wear eye protection and a hard hat. - Page 16 DD 500 Gear Core bit diameter Speed under no load 82–92 mm / 3 ˝ – 3 ˝ 102–112 mm / 4˝ – 4 ˝ 122–132 mm / 4 ˝ – 5 ˝ 142–172 mm / 5 ˝–6 ˝ 182–202 mm / 7˝–8˝ 225–250 mm / 9˝–10˝...
- Page 17 The wet-type vacuum cleaner must be switched on man- 6.7 Switching off ually before beginning drilling and switched off manu- 1. Switch off the machine. ally at the end of the drilling operation. 2. Withdraw the diamond core bit from the hole. -CAUTION- -CAUTION- Check that the core bit and water collector are centered...
-
Page 18: Maintenance
Remove any dirt adhering to parts and rub the core bits or when the controls do not function faultlessly. If nec- and the chuck with an oily cloth from time to time to pro- essary, the machine should be repaired at a Hilti repair tect their surfaces from corrosion. center. -
Page 19: Troubleshooting
305540 Cross-column adaptor 202992 Drainage hose Connector (for dry drilling) 46938 000000 Vacuum cleaner (for dry drilling, e.g. Hilti VCU 40, VCD 50) 9. Troubleshooting Remedy Fault Possible cause Plug in another electric appliance and check The machine doesn’t start Fault in the electric supply whether it works. - Page 20 Free the core bit. Switch the motor off and (stalled) for too long. then on again. Electric power failure. Check the plug connections, electric supply, GFCI (DD 350) and fuse in the electric supply. Electronics defective. Have the machine repaired at a Hilti service center.
-
Page 21: Disposal
10. Disposal Recycle waste material Most of the materials from which Hilti tools or machines are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools for recycling. - Page 22 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3074 | 0613 | 00-Pos. 3 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 401008 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5145291 / 000 / 01...