Related Manuals for scope SCPUHF
Summary of Contents for scope SCPUHF
- Page 1 SCOPE COMMUNICATIONS UK LTD SCPUHF Four Zone POCSAG Paging Transmitter User Manual Scope Communications UK Ltd Quantum House, Totnes, Devon TQ9 5AL England. Tel: 01803 860700 Email: sales@scope-uk.com SCPUHF Issue 2...
- Page 2 Important Installation Information It is the purchasers’ responsibility to determine the suitability of this equipment and its derivatives for any given application, Scope cannot give specific advice in this manual, as each use will require independent evaluation. Scope has, wherever possible, employed extra safeguards to monitor the system’s performance.
- Page 3 This product complies with the essential requirements of the R&TTE Directive 1999/5/EC Copies of the Declaration of Conformity covering this product can be obtained from Scope at Quantum House, Steamer Quay, Totnes TQ9 5AL United Kingdom.
-
Page 4: System Overview
SCPUHF Paging Transmitter System System Overview The SCPUHF is a simple flexible UHF POCSAG radio paging transmitter designed to interface with almost any control equipment. It has four “change of state” input zones, three of which are dry contact and one which has either a 12V or 0V trigger input. It is normally supplied with one numeric radio pager, which is matched to the system serial number and base transmitter identity code. -
Page 5: Section 2: Installation
SCPUHF Paging Transmitter System d) Mode Setting There are 3 modes available. These are set on switches 7 and 8 on the 8-way bank (SW2). The following modes are available: Switches FUNCTION Mode 1 1 PAGER NUMBER, INDICATING 4 INDIVIDUAL ZONES... - Page 6 Damage caused by incorrect connection is the responsibility of the installer! The following procedure must be adhered to when installing the SCPUHF paging system. Ensure you have taken into consideration all of the above information before selecting the location for your transmitter.
- Page 7 Applying voltage to these inputs will cause irreparable damage. Zone 4 requires either a +12V or 0V dc input. If in doubt, check with Scope before proceeding; incorrect connection may cause permanent damage. For the SCPUHFTX unit, connect the power input lead to the + and – terminals provided (see diagram 3).
- Page 8 SCPUHF Paging Transmitter System Installation The Transcoder PCB contains static sensitive components. Care should be taken to avoid contact wherever possible and anti-static precautions should be observed during installation. Diagram 1: SCPUHFTX SCPUHF Issue 2...
- Page 9 SCPUHF Paging Transmitter System Diagram 2: PSCPETX Case Top Panel View Case Securing Screws (slacken to remove cover) Case Bottom Panel View SCPUHF Issue 2...
-
Page 10: Section 3: Operation
SCPUHF Paging Transmitter System Section 3: Operation The controller is in the sleep mode for most of the time, and will wake up every 1.2 seconds to read the inputs. If the RESET input is closed, the inputs are effectively disarmed and no pages will be sent, regardless of the input states. - Page 11 SCPUHF Paging Transmitter System Check that the power source is the correct type (12 to 14V dc) and correctly wired to the terminals provided (see diagram 3). Check that the green LED lights for the duration of the transmission. If not, go back to the cabling and re-check the terminal connections.
- Page 12 SCPUHF Paging Transmitter System Diagram 3: Transcoder PCB terminal connections SCPUHF Issue 2...
-
Page 13: Other Antennas
Pagers returned with flat, incorrectly installed or leaking batteries will be charged for! In the event that a pager requires service, return it directly to Scope in the pre-addressed service bag supplied with your system by registered post. Ensure that you carefully fill out the service form provided. -
Page 14: System Specification
PSCPETX: 328 (L) x 190 (W) x 75 (D) max SCPUHFTX: 184 (L) x 138 (W) x 45 (D) max excluding aerial Scope’s policy is one of continuous development and specifications are subject to change without prior notice SCPUHF Issue 2...