Table of Contents
Advertisement
22 electrolux e:line ovens maintenance and cleaning
Maintenance and cleaning
warning
• Do not use steam cleaners.
• D o not line the bottom of the oven with foil
or cookware.
Stainless steel
• A ll grades of stainless steel can stain, discolour or become
greasy. You must clean these areas regularly by following
the procedures below, if you want your appliance to look
its best, perform well and have a long life.
• C are must be taken when wiping exposed stainless
steel edges, they can be sharp!
• T he front frame around the oven can be cleaned
with stainless steel cleaners if it becomes soiled or
discoloured.
• A suitable cleaner can be purchased from Electrolux
Customer Care Centres.
caution
• T he oven door and control panel is decorated with a
special stainless steel that resists finger marks and should
only be cleaned with warm water and a mild detergent.
• D O NOT use stainless steel cleaners, abrasive cleaners
or harsh solvents.
Note:
• M ake sure you follow the polish or brushing lines in the steel.
Glass
• G lass surfaces on doors and control panels are best
cleaned immediately after soiling.
• A damp cloth may help remove baked on food deposits.
• O ven cleaners can be used to remove stubborn marks
and stains.
caution
The door glass on this appliance is made from a tough,
durable material that withstands heating and cooling
without breaking.
However, it must be remembered that it is GLASS, it may
break. Treat it accordingly! Should you have any questions
about the glass in your new appliance, please contact the
customer care centre by dialling 1300 363 640.
Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door since they can scratch
the surface, which may result in shattering of the glass.
Oven
• A lways keep your appliance clean. Ensure fats and oils
do not accumulate around elements, burners or fans.
• A lways keep the oven dish, bake trays and grill dish
inserts clean, as any fat deposits may catch fire.
• A lways wrap your meats in foil or an oven roasting bag
to minimise cleaning. Any polyunsaturated fats can leave
a varnish-like residue which is very difficult to remove.
Note:
• R efer also to Pyrolitic oven cleaning on page 28.
((EPEE63CS & EPEE63CK models only)
Grill
• A lways keep the grill dish and grill insert clean, as any
fat deposits may catch fire.
Cleaning your accessories
Removing the trays and shelves from your appliance
• S lide the dish and shelves towards you until they reach
the front stop.
• T ilt them up at the front to clear the side supports,
taking care not to spill the contents.
• Lift them clear.
• W ash the dish and insert the shelves in hot soapy water.
• R everse the above steps to put the grill dish and shelves
back again.
• E nsure that they are placed between two support wires.
• To remove a tray from a sliding position:
– Pull tray towards you until it stops.
– Lift the tray clear.
Removing the side racks
1. Grasp the middle wire at the front.
2. Pull firmly inwards.
removing and replacing the oven top light (EPEE63CS & EPEE63CK models only) electrolux e:line ovens 23
warning
IMPORTANT: Make sure the appliance is turned off
before you remove or replace parts, to avoid the
possibility of electric shock.
Removing and replacing the oven back light and
side light
• T urn oven light glass anticlockwise to remove it for
globe replacement.
• T o remove side light, place a spoon under the light glass
and lever off. Replace globe and snap glass cover back
into position.
• A special high temperature resistant globe should be
used. This can be purchased from Electrolux Customer
Care Centre.
Releasing the grill element
We have designed the upper element with a rotating latch
to help you reach your oven roof for cleaning.
• R otate latch until the element drops down freely.
Replacing the oven top light
(EPEE63CS & EPEE63CK models only)
• The top light is positioned behind the grill deflector at the
top of the oven.
• To remove the globe the shelves should first be removed
from the oven and the top element dropped down.
• Insert a small screwdriver into the glass cutout between
the two metal clips on the left hand side, as shown in
the diagram.
• G ently lever the glass cover off, by pushing the screw
driver in and moving it upwards, whilst holding the glass
cover with the other hand. (If not supported, the glass
cover may fall and break).
• Remove the faulty globe by pulling it directly out of
its holder.
• Replace the old globe with a new one, ensuring not to
directly touch the surface of the globe with your fingers,
(A tissue or soft cloth is best for this.)
• P ick up the glass cover and place short edge into right
side of housing; push up opposite end of glass cover
until it snaps into position.
• Resecure the top element in place.
Hide quick links:
Advertisement
Table of Contents
