Removing The Wiring Harness - Hunter Ceiling fans Installation And Operation Manual

NOTE: Both plug connectors are polarized and will only fit to-
gether one way. Make sure that both connectors are properly
aligned before connecting them together. Incorrect connec-
tion could cause improper operation and damage to the prod-
uct.
Lower Plug
Connector
Housing
Assembly
Screw
F F F F F i i i i i g g g g g ur ur ur ur ure 27 - C e 27 - Co o o o o nn e 27 - C e 27 - C e 27 - C nn nn nne e e e e c c c c c t t t t t in in in in ing t nn
2. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the up-
per switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 27.
TM
installing the Easy Lock
1. Insert the glass shade into the cup around the bulb socket as
shown in Figure 28.
2. While holding the fitter with one hand, twist the glass shade
clockwise to lock in place.
3. Install max 60 Watt medium base incandescent bulbs.
NOTE: To remove the glass shade, first remove the bulb then
twist the shade counterclockwise.
Cup
Neck of
Glass Shade
F F F F F i i i i i g g g g g ur ur ur ur ure 28 - I e 28 - I e 28 - I e 28 - In n n n n s s s s s t t t t t a a a a a llin e 28 - I
© 2003 Hunter Fan Company
Upper Switch
Housing
Upper Plug
Connector
Lower
Switch
Housing
g t g t g th h h h h e p g t e p e plu lu lu lu lug c e p e p g c g c g c g co o o o o nn nn nn nne e e e e c c c c c t t t t t o o o o o r r r r r s s s s s nn
glass shades
lling t llin llin llin g t g t g t g th h h h h e g e g e g e g e gl l l l l a a a a a s s s s s s s s s s s s s s sh h h h h a a a a a d d d d d e e e e e s s s s s
installing without the light fixture
Your Hunter fan comes with an integrated light fixture assembly
and an optional switch housing. This feature gives you the option
of installing the fan with or without the included light fixture.
If you decide to install the fan without the integrated light fixture
please complete the following instructions to install the optional
switch housing.
attaching the upper switch housing
1. Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 25.
2. Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 25.
3. Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.
4. Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 26. Install the one re-
maining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.
C C C C C A A A A A U U U U U T T T T T I I I I I O O O O O N: M N: M N: M N: Ma a a a a k k k k k e s e s e sur ur ur ur ure t e s
N: M e s
c c c c c ur ur ur ur ure e e e e l l l l l y a y a y a y a y at t t t t t t t t t a a a a a c c c c c h h h h h e e e e e d t d to t d t d t d t o t o th h h h h e s e s e s e s e sw w w w w i i i i i t t t t t c c c c c h h o t o t
ur ur ur ur ure t e t e t e to p o p o pr r r r r o o o o o p p p p p e e e e e r r r r r l l l l l y a o p y at t t t t t t t t t a a a a a c c c c c h a y a y a h a h an n n n n d t h a
e t o p y a h a
s s s s s e e e e e mb mb mb mbl l l l l y s mb y s y s y s y sc c c c c r r r r r e e e e e w w w w w s c s c s c s c s co o o o o ul ul ul ul uld r d r d r d re e e e e s s s s s ul ul ul ul ult in t d r
f f f f f i i i i i x x x x x t t t t t ur ur ur ur ure f e f e f e f e fa a a a a llin llin lling g g g g . . . . . llin
llin
attaching the lower switch housing

removing the wiring harness

Before you can install the optional switch housing, you must re-
move the wiring harness and its components from the integrated
light fixture. You must then install the wiring harness into the op-
tional switch housing.
Refer to Figure 29.
1. Locate the reversing switch and carefully remove the two screws
holding the reversing switch to the light fixture housing. The
reversing switch can now be removed from the light fixture
housing.
2. Remove the patented breakaway connector from the fan pull
chain.
3. Carefully loosen the bellmouth nut from the fan pull chain
and remove the fan pull chain switch from the light fixture
housing.
4. Locate and carefully remove the two capacitors from the light
fixture assembly.
5. In the light fixture assembly you will find two different plug
connectors: One multi-wire connector and two two-wire con-
nectors. Unplug the two-wire connectors; one connector will
have a black with white stripes wire and a white wire coming
from the multi-wire connector.
6. You have now disconnected the wiring harness and its com-
ponents from the light fixture housing and are ready to install
them into the optional switch housing.
e th h h h h e up e t e t e up e upp p p p p e e e e e r s r s r s e up r s r sw w w w w i i i i i t t t t t c c c c c h h h h h ho o o o o u u u u u sin h h sin sin g i g i g i g is s
e t e up h h sin sing i
h h h h h ho o o o o u u u u u sin h h sin sin sing m sin g m g mo o o o o un g m g m un unt t t t t in in in in ing p un un g p g p g p g pl l l l l a a a a a t t t t t e e e e e . F . F . F . F . Fa a a a a il- il- il- il- il-
d t d ti i i i i g g g g g h h h h h t t t t t e e e e e n a d t n a n all t n a ll thr hr hr hr hre e e e e e h ll t ll t e ho o o o o u u u u u sin e h e h sin sin sing a
d t n a ll t e h sin
t in t t in th h h h h e s t in t t in t e s e sw w w w w i i i i i t t t t t c c c c c h h e s e s h h h h h h h ho o o o o u u u u u sin sin sin sin sing a g a g a g an n n n n d li g a
41822-01 10/22/2003
9 9 9 9 9
s s s se- e- e- e- e- s s s s
g a g as s s s s - - - - - g a
g a
d lig g g g g h h h h h t t t t t d li d li d li