Wegener UNITY4000 Instruction Manual page 72

DEFAULT CUSTOMER CONFIGURATION SHEET
( When customer supplied, WCI must receive this information at least two weeks before delivery to avoid additional processing
charges to the customer.)
Model Number:_UTY4000________________________________ Release: __________
Customer:___________________________________
Sales Order Number:_____________________________________________________________
Uplink Encoder Make/Model: _____________________________ Video Format: ___________
Customer Approval:________________________________ Date:________________________
(only required for nonstandard configuration)
Special Instructions or
Clarifications:____________________________________________________________________________________________
___________________________________________________
(Circle or write-in requirements, default values are shown bold and underlined. Consult Wegener Engineering about changes to
1.0 MODE DIP Switch: Position 1, 2: Reserved
2.0 LNB DC (on RF-In jack) ( Yes --jumper J22 , No -- no jumper on J22 )
3.0 Alarm Relay-contact Polarity [Note: Relay is in "alarm" state when unit power is off] (Close-on-alarm--J17 non-dot ,
Open-on-alarm--J17 dot)
4.0 Initial Carrier Settings:
4.1 Carrier Frequency: ________________MHz ( 3700.00 to 14000.00) 12000.00 MHz
4.2 Feed Port (if RF switch option is installed) ( 1, 2, 3, 4)
4.3 Transport Rate: ____________Mbps (2.500 to 48.382 in 0.001 Mbps steps) 6.000 Mbps *
4.4 Program Number: ___________ (default is * for lowest found)
4.5 FEC Rate: ( ½ , 2/3, 3/4, 5/6, 7/8 )
4.6 Tag Site Number: ______ (0 -15) 0 -- Tag Site 15 designates no--COMPEL or tags
4.7 SNR (Eb/No) Alarm Level ________dB (2 to 7 dB) 4 dB
4.8 Margin Warning Offset ________dB 2 dB -- sum of this and SNR Alarm level <12 dB
* Check product spec for legal upper limits on aggregate Transport rate vs. FEC Rate.
5.0 LNB LO Settings (std. domestic Ku-band is 10750 MHz, C-band is 5150 MHz)
5.1 LNB LO Frequency (if no RF Switch is installed): ________________MHz 10750 MHz !
5.2 LNB LO Freq. (for Feed Port 1 only if RF switch installed): ________________MHz 10750 MHz !
5.3 LNB LO Freq. (for Feed Port 2 only if RF switch installed): ________________MHz 10750 MHz !
5.4 LNB LO Freq. (for Feed Port 3 only if RF switch installed): ________________MHz 10750 MHz !
5.5 LNB LO Freq. (for Feed Port 4 only if RF switch installed): ________________MHz 10750 MHz !
6.0 Initial Audio Settings
6.1 Ch 1 Audio Routing: ( Stereo, Reverse Stereo, Orig L to both, Orig R to both)*
6.2 Ch 2 Audio Routing: ( Stereo, Reverse Stereo, Orig L to both, Orig R to both)*
6.3 Ch 1 Program: ____________ ( need three-character code, default is * for lowest found)
6.4 Ch 2 Program: ____________ ( need three-character code, default is * for lowest found)
* "Orig L or R" designates orginal L or R inputs to the MPEG encoder unit.
UTY4000-003
Equipment Settings
default settings shown with '!' exclamation mark.)
Position 3: Test Mode (leave in UP position to disable)
Position 4: LNB Power off (up) / LNB Power on (down)
Header: ___ ___ ___ ___ (WXXX)