Desa VVF36 Owner's Operation And Installation Manual page 22

You.may.test.blower.for.operation.by.turning.
control. knob. clockwise. just. until. it. clicks. on.
which.is.the.full.on.position..Adjust.fan.speed.
to.lowest.setting.(this.should.be.no.more.than.
1/4.of.a.turn.clockwise).
For.Optional.
Fan.Kit
From.Blower.
Assembly
Figure 37 - Connecting Blower
Accessory to Power Supply
OPTIONAL WIRELESS HAND-HELD
REMOTE CONTROL INSTALLATION
Note: If using an optional wireless hand-
held remote control, wall switch is no longer
operational.
NOTICE: Only use alkaline bat-
teries (not included).
Installing HRC100 Model Remote Control
(Millivolt Models Only)
1.. Remove. lower. louver. access. panel. in.
fireplace (see step 1 of Wall Switch Instal-
lation, page 21).
.. Disconnect.wall.switch.wires.from.termi-
nals. marked.TH. and.TPTH. (see. Figure.
35, page 21).
3.. Slide. 9-volt. battery. into. clip. on. back. of.
remote.receiver.and.connect.battery.termi-
nals.to.battery..Mount.receiver.onto.bracket.
with.clips.provided.(see.Figure.38).
9-Volt.Battery
Receiver.Clip
Gas.
Valve
Terminal.
Wires
16AI
E A
To.Thermopoile
Figure 38 - Installing Remote Receiver
(HRC100)

FIREPLACE INSTALLATION
Continued
Plastic.Mounting.Clips
White
Red
FRONT
www.desatech.com
4.. Connect. white. wire. to. control. valve. ter-
minal. TH. and. red. wire. to. TPTH.. Move.
remote. select. switch. to. the. REMOTE.
position.
5.. Replace.louvered.access.panel.by.follow-
ing.reverse.steps.on.page.1.
6.. Remove.battery.cover.on.back.of.hand-
held.remote.(see.Figure.39)..Remove.and.
discard.sensor.tag.
7.. Attach. terminal. wires. to. 9-volt. battery..
Place.battery.into.housing.
8.. Replace. battery. cover. onto. hand-held.
remote.
9.. Set.selector.switch.on.receiver.to.the.OFF.
position.if.you.will.be.away.from.unit.for.
an.extended.period.of.time.
Battery.
Cover
Terminal.
Wires
9-Volt.Battery
Figure 39 - Installing Battery in Hand-
Held Remote Control Unit (HRC100)
Installing SKYTECH/WRC Model Remote
Control (Electronic Models Only)
1.. Remove. lower. louver. access. panel. in.
fireplace (see step 1 of Wall Switch Instal-
lation, page 21).
2. If a wall switch was installed, it must be
removed. from. ignition. control. circuit. for.
remote. to. work. properly.. Remove. wire.
nuts. from. switch. connection. at. ignition.
control module. Using wire nut, connect
transformer.(blue).wire.to.remaining.wire.
connected. to. control. terminal. marked.
P.SW (see Figure 34, page 21).
3. The receiver does not require a battery.
To install, plug extension cord into one of
the.outlet.receptacles.on.outlet.box..Plug.
receiver.unit.into.extension.cord.and.igni-
tion.module.into.receiver.unit.(see.Figure.
40, page 23).
4.. Replace.louvered.access.panel.by.follow-
ing.reverse.steps.on.page.1.
5.. Activate. handset. battery. by. removing.
insulating tab on back (see Figure 41,
page.3).
Remote.Control.Unit
Sensor.
Tag
Battery.
Housing
56131H