Adjusting The Graphic Equalizer Curve; Adjusting The Time Correction; Adjusting The Crossover Settings - Alpine CDA-9886 Quick Reference Manual

Adjusting the Graphic Equalizer Curve
You can modify the equalizer sellings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve.
set the EQ MODE to GRAPHIC EQ. For details. refer to "Selling EQ
mode" (page 28).
Adjusting the Time Correction
Before performing the following procedures. refer to "About Time
Correction" (page 31).
1
After selecting T.CORRECTION from the SOUND
ADJUST mode, press BAND to select a speaker to
be adjusted.
1
After selecting GRAPHIC EQ from the SOUND
ADJUST mode, press
BAND
to select the band to be
adjusted.
B 1
-7
B 2
-7
B 3
-7
B 4
-7
B 5
-7
B 6
-7
B 7
-7
B 1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (63 kHz) /
Band-7 (17.5 kHz)
2
Turn the
Rotary encoder
to adjust the level.
Adjustable output level: -6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and
then adjust all bands.
20 Hz-200 Hz
20 Hz-20 kHz
(1 kHz-20 kHz)*I/(20 Hz-20 kHz),.]
2.2ch (3WAY) System
setting items:
LOW / M-L
M-H
HIGH
Press SOURCEI<!> to adjust the slope.
Adjustable slope: FLAT*. 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
3
2.2ch (3WAY) System' NORMAL (L=R)
setting items:
LOW / M-L / M-H / HIGH
*1
When Maker's is selected, refer to "Setting the Response Slope for
the High Range Speaker (TW SETUP)" (page 27).
*2 When User's is selected, refer to "Setting the Response Slope for the
High Range Speaker (TW SETUP)" (page 27).
2.2ch (3WAY) System 'INDIVIDUAL (UR)
Setting items:
L-L / L-R / ML-L / ML-R / MH-L / MH-R / H-L / H-R
2
Press ... or .. to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
1
After selecting CROSSOVER from the SOUND
ADJUST mode, press
BAND
to select the band to be
adjusted.
Adjusting the Crossover Settings
Before performing the following procedures. refer to "About the
Crossover" (page 32).
R-L
-7
R-R
-7
(High-L) (High-R)
2.2ch (3WAY) System
F-L (Initial setting)
-7
F-R
-7
(Mid-L) (Mid-R)
SW-L
-7
SW-R
-7
F-L
(Mid-L)
4.2ch (FRONT'REARISUBW.) System
F·L (Initial setting)
-7
F-R
-7
R-L
-7
R-R
-7
(Front-L) (Front-R) (Rear·L) (Rear-R)
SW-L
-7
SW-R
-7
F-L
(Front-L)
2
Turn the
Rotary encoder
to adjust the distance
correction value. (0.0 to 336.6cm).
L
=
(distance to farthest speaker) - (distance to other
speakers)
Refer to "Time Correction Value List" on page 31.
3
Repeat steps 1 and 2 to set another speaker.
By
setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
*
FLAT can be setfor the HIGH slope only when USER'S is selected in
"Setting the Response Slope for the High Range Speaker (TW
SETUP)" (page 27). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to
FLAT.
4
Turn the Rotary encoder to adjust the output level.
Adjustable output level -12 to 0 dB.
5
Repeat steps 1 to 4 to make adjustment to the other
bands.
29-EN
Adjusting the Graphic Equalizer Curve
You can modify the equalizer sellings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve.
set the EQ MODE to GRAPHIC EQ. For details. refer to "Selling EQ
mode" (page 28).
Adjusting the Time Correction
Before performing the following procedures. refer to "About Time
Correction" (page 31).
1
After selecting T.CORRECTION from the SOUND
ADJUST mode, press BAND to select a speaker to
be adjusted.
1
After selecting GRAPHIC EQ from the SOUND
ADJUST mode, press
BAND
to select the band to be
adjusted.
B 1
-7
B 2
-7
B 3
-7
B 4
-7
B 5
-7
B 6
-7
B 7
-7
B 1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (63 kHz) /
Band-7 (17.5 kHz)
2
Turn the
Rotary encoder
to adjust the level.
Adjustable output level: -6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and
then adjust all bands.
20 Hz-200 Hz
20 Hz-20 kHz
(1 kHz-20 kHz)*I/(20 Hz-20 kHz),.]
2.2ch (3WAY) System
setting items:
LOW / M-L
M-H
HIGH
Press SOURCEI<!> to adjust the slope.
Adjustable slope: FLAT*. 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
3
2.2ch (3WAY) System' NORMAL (L=R)
setting items:
LOW / M-L / M-H / HIGH
*1
When Maker's is selected, refer to "Setting the Response Slope for
the High Range Speaker (TW SETUP)" (page 27).
*2 When User's is selected, refer to "Setting the Response Slope for the
High Range Speaker (TW SETUP)" (page 27).
2.2ch (3WAY) System 'INDIVIDUAL (UR)
Setting items:
L-L / L-R / ML-L / ML-R / MH-L / MH-R / H-L / H-R
2
Press ... or .. to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
1
After selecting CROSSOVER from the SOUND
ADJUST mode, press
BAND
to select the band to be
adjusted.
Adjusting the Crossover Settings
Before performing the following procedures. refer to "About the
Crossover" (page 32).
R-L
-7
R-R
-7
(High-L) (High-R)
2.2ch (3WAY) System
F-L (Initial setting)
-7
F-R
-7
(Mid-L) (Mid-R)
SW-L
-7
SW-R
-7
F-L
(Mid-L)
4.2ch (FRONT'REARISUBW.) System
F·L (Initial setting)
-7
F-R
-7
R-L
-7
R-R
-7
(Front-L) (Front-R) (Rear·L) (Rear-R)
SW-L
-7
SW-R
-7
F-L
(Front-L)
2
Turn the
Rotary encoder
to adjust the distance
correction value. (0.0 to 336.6cm).
L
=
(distance to farthest speaker) - (distance to other
speakers)
Refer to "Time Correction Value List" on page 31.
3
Repeat steps 1 and 2 to set another speaker.
By
setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
*
FLAT can be setfor the HIGH slope only when USER'S is selected in
"Setting the Response Slope for the High Range Speaker (TW
SETUP)" (page 27). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to
FLAT.
4
Turn the Rotary encoder to adjust the output level.
Adjustable output level -12 to 0 dB.
5
Repeat steps 1 to 4 to make adjustment to the other
bands.
29-EN